The OMAP wrapper allows us to either control internal
OTG signals via SW or HW. Different boards might wish
to use one or the other mode of operation. Let's have
have that information passed via platform_data for now.
After DT conversion is finished for OMAP, we can easily
convert this to a DT attribute.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We need to have actual HW in order to implement
and test that part of the code anyway. Until then
it's best to remove it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
this field will hold the next expected event.
In certain cases, host might fall into some error
condition and ask from us the wrong Control phase.
On such situations, we should stall and restart.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Whenever we issue a Set Stall command on EP0,
the state machine will be restarted and Stall
is cleared automatically, when core receives
the next SETUP packet.
There's no need to track that EP0_STALL state.
Signed-off-by: Felipe Balbi <balbi@ti.com>
when we're going to issue Set Stall command,
we should clear DWC3_EP_STALL flag, but also
we should clear BUSY, HALTED and all others.
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are two spots where we wait until the HW finishes processing a
certain command. Initially we had a few problems and we used 500ms as a
limit to be on a the safe side. Paul Zimmerman mentioned this is little too
much. After a debugging session, we noticed that we hardly ever go over 20us
and didn't pass 30usec so far. Using mdelay() seems way overloaded.
Giving the current numbers 500usec as the upper limit is more than enough.
Should it ever timeout then something is definitely wrong.
While here, also replace the type with u32 since long does not really
fit here.
Cc: Paul Zimmerman <paul.zimmerman@synopsys.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- since a while we are disabling an endpoint and purging every requests on
RESET and DISCONNECT which leads to a warning since the endpoint was
disabled twice (once by the UDC, and second time by the gadget). I
think UDC should nuke all requests because all those requests
become invalid. It's gadget driver's responsability, though, to disable
its used endpoints. This is done by merging dwc3_stop_active_transfer()
and dwc3_gadget_nuke_reqs() into dwc3_remove_requests().
- dwc3_stop_active_transfer() is now no longer called unconditionaly.
This has the advantage that it is always called to disable an active
transfer which means if res_trans_idx 0 than something went wrong and
it is an error condition because we can't clean up the requests.
- Remove the DWC3_EP_WILL_SHUTDOWN which was introduced while
introducing the command complete part for dequeue. All requests on
req_queued list should be removed during the dwc3_cleanup_done_reqs()
callback so there is no reason to go through the list again.
We consider it an error condition if requests are still on this
list since we never queue TRB without LST=1 (the last requests has
always LST=1, there are no requests with LST=0 behind it).
[ balbi@ti.com : reworked commit log a bit, made patch apply ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We read the DWC3_GSNPSID register to make sure we got the correct
register offset passed. One of the recent commits moved the soft reset
before this so in case of the wrong offset we end up with "reset timed
out". This patch moves the "id" check before the reset again.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are some issues around for enabling/disabling this mode and
handling it. It does not work perfectly (yet). However we have a few
gadgets tested successfuly so far. That means we are quite confident
that we won't need this in near future.
So I'm for removing it and bringing a working version back once there is
a need for it.
Thanks to Dan Carpenter who spotted the wrong memory handling here.
[ balbi@ti.com : made it actually apply ]
Cc: Dan Carpenter <error27@gmail.com>
Cc: wharms@bfs.de
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The DesignWare USB3 core tells us which phase
of a control transfer should be started, it
also tells us which physical endpoint needs
that transfer.
With these two informations, we have all we
need to simply EP0 handling quite a lot and
get rid rid of the SW state machine tracking
ep0 states.
For achieving this perfectly, we needed to
add support for situations where we get
XferNotReady while endpoint is still busy
and XferNotReady while gadget driver still
hasn't queued a request.
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case we have transfers which aren't aligned
to wMaxPacketSize, we need to be careful with
how we start the transfer with the HW. OUT
transfers _must_ be aligned with wMaxPacketSize
and in order to guarantee that, we use a bounce
buffer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This core cannot handle OUT transfers which aren't
aligned to wMaxPacketSize, but that can happen at
least on control endpoint with the USB Audio Class.
This patch adds a bounce buffer to be used on the
case of a non-aligned ep0out request is queued.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The status field of the Transfer Not Read event
is different on Control Endpoints. On this patch
we are just adding the defines to be used on a
later patch which will re-work the control endpoint
handling.
Signed-off-by: Felipe Balbi <balbi@ti.com>
the previous message had too little meaning. Make
it more human readable and use the macro we already
had for extracting the command completion status out
of DEPCMDn register.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if we don't set DMA address to invalid when unmapping,
we might fall in a situation where request buffer
can't be mapped to DMA again.
Signed-off-by: Felipe Balbi <balbi@ti.com>
We may as well fix this potential leak so we don't have to listen to
the static checkers complain.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Without this patch we won't clear that bit and instead will
clear all other bits on our endpoint flag.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Felipe Balbi
Sebastian Andrzej Siewior
Dan Carpenter