Due to commit cdda911c34, evdev only
becomes readable when the buffer contains an EV_SYN/SYN_REPORT event. If
we get a repeat or a scancode we don't have a mapping for, we never call
input_sync, and thus those events don't get reported in a timely
fashion.
For example, take an mceusb transceiver with a default rc6 keymap. Press
buttons on an rc5 remote while monitoring with ir-keytable, and you'll
see nothing. Now press a button on the rc6 remote matching the keymap.
You'll suddenly get the rc5 key scancodes, the rc6 scancode and the rc6
key spit out all at the same time.
Pressing and holding a button on a remote we do have a keymap for also
works rather unreliably right now, due to repeat events also happening
without a call to input_sync (we bail from ir_do_keydown before getting
to the point where it calls input_sync).
Easy fix though, just add two strategically placed input_sync calls
right after our input_event calls for EV_MSC, and all is well again.
Technically, we probably should have been doing this all along, its just
that it never caused any functional difference until the referenced
change went into the input layer.
input_sync once per IR signal. There was another hidden bug in the code
where we were calling input_report_key using last_keycode instead of our
just discovered keycode, which manifested with the reordering of calling
input_report_key and setting last_keycode.
Reported-by: Stephan Raue <sraue@openelec.tv>
CC: Stephan Raue <sraue@openelec.tv>
CC: Mauro Carvalho Chehab <mchehab@redhat.com>
CC: Jeff Brown <jeffbrown@android.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While 0xffdc devices have their IR protocol hard-coded into the firmware
of the device, we have no known way of telling what it is if we don't
have the device's config byte already in the driver. Unknown devices
default to the imon native protocol, but might actually be rc6, so we
should set the driver up such that the user can load the rc6 keytable
from userspace and still have a working device ahead of its config byte
being added to the driver.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Another device with the 0xffdc device id, this one with 0x7e in the
config byte. Its an iMON VFD + RC6 IR, in a CoolerMaster 260 case.
Reported-by: Filip Streibl <filip@streibl.cz>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The comment says "wait 15ms", but the code says jiffies_to_msecs(15)
instead of msecs_to_jiffies(15). Fix that. Tested, works fine with both
rc5 and rc6 decode, in-kernel and via lirc userspace, with an HVR-1150.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With hardware that has to use ir_raw_event_store_edge to collect IR
sample durations, we were not doing an event reset unless
IR_MAX_DURATION had passed. That's around 4 seconds. So if someone
presses up, then down, with less than 4 seconds in between, they'd get
the initial up, then up and down upon pressing down.
To fix this, I've lowered the "send a reset event" logic's threshold to
the input device's REP_DELAY (defaults to 500ms), and with an
saa7134-based GPIO-driven IR receiver in a Hauppauge HVR-1150, I get
*much* better behavior out of the remote now. Special thanks to Devin
for providing the hardware to investigate this issue.
CC: stable@kernel.org
CC: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There's really no good reason not to just grab the desired IRQ at driver
init time, instead of every time the lirc device node is accessed. This
also improves the speed and reliability with which a serial transmitter
can operate, as back-to-back transmission attempts (i.e., channel change
to a multi-digit channel) don't have to spend time acquiring and then
releasing the IRQ for every digit, sometimes multiple times, if lircd
has been told to use the min_repeat parameter.
CC: devel@driverdev.osuosl.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We were calling schedule_timeout with the rx thread's task state still
at TASK_RUNNING, which it shouldn't be. Make sure we call
set_current_state(TASK_INTERRUPTIBLE) *before* schedule_timeout, and
we're all good here. I believe this problem was mistakenly introduced in
commit 5bd6b0464b, and I'm not sure how I
missed it before, as I swear I tested the patchset that was included in,
but alas, stuff happens...
Acked-by: Andy Walls <awalls@md.metrocast.net>
CC: stable@kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Both consumers of RC_MAP_PINNACLE_PCTV_HD send along full RC-5
scancodes, so this update makes this keymap actually *have* full
scancodes, heisted from rc-dib0700-rc5.c. This should fix out of the box
remote functionality for the Pinnacle PCTV HD 800i (cx88 pci card) and
PCTV HD Pro 801e (em28xx usb stick).
CC: stable@kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to the intrepid testing and debugging of Matthijs van Drunen, it
was uncovered that at least some variants of the ITE8709 need to use pnp
resource 2, rather than 0, for things to function properly. Resource 0
has a length of only 1, and if you try to bypass the pnp_port_len check
and use it anyway (with either a length of 1 or 2), the system in
question's trackpad ceased to function.
The circa lirc 0.8.7 lirc_ite8709 driver used resource 2, but the value
was (amusingly) changed to 0 by way of a patch from ITE themselves, so I
don't know if there may be variants where 0 actually *is* correct, but
at least in this case and in the original lirc_ite8709 driver author's
case, it sure looks like 2 is the right value.
This fix should probably be applied to all stable kernels with the
ite-cir driver, lest we nuke more people's trackpads.
Tested-by: Matthijs van Drunen
CC: Juan Jesús García de Soria <skandalfo@gmail.com>
CC: stable@kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
mx1_camera_add_device() can return an uninitialized value of ret.
Signed-off-by: Andre Bartke <andre.bartke@gmail.com>
[g.liakhovetski@gmx.de: modified the fix to remove "ret" completely]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The usecase where, user allocates small size of buffer
through bootargs (video1_bufsize/video2_bufsize) and later from application
tries to set the format which requires larger buffer size, driver doesn't
check for insufficient buffer size and allows application to map extra buffer.
This leads to kernel crash, when user application tries to access memory
beyond the allocation size.
Added check in both mmap and reqbuf call back function,
and return error if the size of the buffer allocated by user through
bootargs is less than the S_FMT size.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With addition of media-controller framework, now we have various
device nodes (/dev/videoX) getting created, so hardcoding
minor number in video_register_device() is not recommended.
So let V4L2 framework choose free minor number for the device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The omap_vout_new_crop() function has possible bug, uses uninitialized
variable "crop.width/height" which is actually output of the function.
Instead we should be using "try_crop.width/height" to calculate the
resizer value.
Signed-off-by: Vladimir Pantelic <vladoman@gmail.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When failing to start the camera we should disable the queue again, to
rollback into the same initial state. Otherwise re-trying will always
hit -EBUSY
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When freeing memory for the video buffers also remove them from the
irq & main queues.
This fixes an oops when doing the following:
open ("/dev/video", ..)
VIDIOC_REQBUFS
VIDIOC_QBUF
VIDIOC_REQBUFS
close ()
As the second VIDIOC_REQBUFS will cause the list entries of the buffers
to be cleared while they still hang around on the main and irc queues
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If a streaming interface has no supported format, the driver won't
create a video device for the associated terminal. Fix an oops by
ignoring that terminal when creating links between entities.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Entities associated with video device nodes are unregistered in
video_unregister_device(). This destroys the entity even though it can
still be accessed through open video device nodes.
Move the media_device_unregister_entity() call from
video_unregister_device() to v4l2_device_release() to ensure that the
entity isn't unregistered until the last reference to the video device
is released.
Also remove the media_entity_get()/put() calls from v4l2-dev.c. Those
functions were designed for subdevs, to avoid a parent module from being
removed while still accessible through board code. They're not currently
needed for video device nodes, and will oops when a hotpluggable device
is disconnected during streaming, as media_entity_put() called in
v4l2_device_release() tries to access entity->parent->dev->driver which
is set to NULL when the device is disconnected.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a potential NULL pointer dereference by skipping registration of
external entities in case none are provided.
This is useful at least when testing mere memory-to-memory scenarios.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
__vb2_queue_alloc function returns the number of successfully allocated
buffers. There is no point in checking if the returned value is negative.
If this function returns 0, videobuf2 should just return -ENOMEM to
userspace, because no driver can work without memory buffers.
Reported-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
queued_count variable was left untouched during the queue reinitialization
in __vb2_queue_cancel, what might lead to mismatch between the real number
of queued buffers and queued_count variable.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit 31901a078a.
Queue should be reinitialized on each REQBUFS() call even if the memory
access method and buffer count have not been changed. The user might have
changed the format and if we go the short path introduced in that commit,
the memory buffer will not be reallocated to fit with new format.
The previous patch was just over-engineered optimization, which just
introduced a bug to videobuf2.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add __GFP_NOWARN parameter to videobuf2 dma-sg allocator to prevent
kernel warning and stack dump if there is not enough memory available.
Videobuf2 and drivers should correctly handle no memory case, so there
is no need for stack dump and extensive log.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Unplugging a pwc cam while an app has the /dev/video# node open leads
to an oops in pwc_video_close when the app closes the node, because
the disconnect handler has free-ed the pdev struct pwc_video_close
tries to use. Instead of adding some sort of bandaid for this.
fix it properly using the v4l2 core's new(ish) behavior of keeping the
v4l2_dev structure around until both unregister has been called, and
all file handles referring to it have been closed:
Embed the v4l2_dev structure in the pdev structure and define a v4l2 dev
release callback releasing the pdev structure (and thus also the embedded
v4l2 dev structure.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Jarod Wilson
Andre Bartke
Vaibhav Hiremath
Vladimir Pantelic
Sjoerd Simons
Laurent Pinchart
Ohad Ben-Cohen
Marek Szyprowski
Hans de Goede
HeungJun, Kim