When operating in a mode that initiates communication and using
HT40 we should fail if we cannot use both primary and secondary
channels to initiate communication. Our current ht40 allowmap
only covers STA mode of operation, for beaconing modes we need
a check on the fly as the mode of operation is dynamic and
there other flags other than disable which we should read
to check if we can initiate communication.
Do not allow for initiating communication if our secondary HT40
channel has is either disabled, has a passive scan flag, a
no-ibss flag or is a radar channel. Userspace now has similar
checks but this is also needed in-kernel.
Reported-by: Jouni Malinen <jouni.malinen@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9287 based PCI & USB devices are differed in eeprom start offset.
So set proper the offset for HTC devices to read nvram correctly.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update pm_qos before removing it in deinit_device to prevent this
warning:
pm_qos_update_request() called for unknown object.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
usb_wait_anchor_empty_timeout's @timeout
wants milliseconds and not jiffies.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When b43legacy is compiled on the arm platform, the following errors are seen:
CC [M] drivers/net/wireless/b43legacy/xmit.o
In file included from include/net/dst.h:11,
from drivers/net/wireless/b43legacy/xmit.c:31:
include/net/dst_ops.h:28: error: expected ':', ',', ';', '}' or '__attribute__'
before '____cacheline_aligned_in_smp'
include/net/dst_ops.h: In function 'dst_entries_get_fast':
include/net/dst_ops.h:33: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_get_slow':
include/net/dst_ops.h:41: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_add':
include/net/dst_ops.h:49: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_init':
include/net/dst_ops.h:55: error: 'struct dst_ops' has no member named
'pcpuc_entries'
include/net/dst_ops.h: In function 'dst_entries_destroy':
include/net/dst_ops.h:60: error: 'struct dst_ops' has no member named
'pcpuc_entries'
make[4]: *** [drivers/net/wireless/b43legacy/xmit.o] Error 1
make[3]: *** [drivers/net/wireless/b43legacy] Error 2
make[2]: *** [drivers/net/wireless] Error 2
make[1]: *** [drivers/net] Error 2
make: *** [drivers] Error 2
The cause is a missing include of <linux/cache.h>, which is present for
i386 and x86_64 architectures, but not for arm.
Signed-off-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to use build-in debugging macro, pci_dev in priv need to be
assigned first.
This fix iwl3945 driver oopsed at boot with 2.6.37-rc1
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This cause 'No Bonding' to be used if userspace has not yet been paired
with remote device since the l2cap socket used to create the rfcomm
session does not have any security level set.
Signed-off-by: Luiz Augusto von Dentz <luiz.dentz-von@nokia.com>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In function l2cap_get_conf_opt() and l2cap_add_conf_opt() the address of
opt->val sometimes is not at the edge of 2-bytes/4-bytes, so 2-bytes/4 bytes
access will cause data misalignment exeception. Use get_unaligned_le16/32
and put_unaligned_le16/32 function to avoid data misalignment execption.
Signed-off-by: steven miao <realmz6@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We've done this for a while in Fedora without any obvious problems other
than some interaction with input devices. Those should be fixed now, so
let's try this in mainline.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When initiating dedicated bonding a L2CAP raw socket with HIGH security
level is used. The kernel is supposed to trigger the authentication
request in this case but this doesn't happen currently for non-SSP
(pre-2.1) devices. The reason is that the authentication request happens
in the remote extended features callback which never gets called for
non-SSP devices. This patch fixes the issue by requesting also
authentiation in the (normal) remote features callback in the case of
non-SSP devices.
This rule is applied only for HIGH security level which might at first
seem unintuitive since on the server socket side MEDIUM is already
enough for authentication. However, for the clients we really want to
prefer the server side to decide the authentication requrement in most
cases, and since most client sockets use MEDIUM it's better to be
avoided on the kernel side for these sockets. The important socket to
request it for is the dedicated bonding one and that socket uses HIGH
security level.
The patch is based on the initial investigation and patch proposal from
Andrei Emeltchenko <endrei.emeltchenko@nokia.com>.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Since the endpoint descriptors (EP3 & EP4) were changed from Interrupt
to Bulk type by firmware, the urb submission done on Bulk pipes.
And the recent commit "check the endpoint type against the pipe type"
added aditional error checking against pipe types under CONFIG_USB_DEBUG.
So bmAttribute has to be updated for both EP3 & EP4 before submitting
urbs on that pipe. This patch resolves the following failure.
[ 2215.710936] usb 1-1: usb_probe_device
[ 2215.710945] usb 1-1: configuration #1 chosen from 1 choice
[ 2215.711152] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 2215.711252] ath9k_hif_usb 1-1:1.0: usb_probe_interface
[ 2215.711255] ath9k_hif_usb 1-1:1.0: usb_probe_interface - got id
[ 2215.712780] usb 1-1: BOGUS urb xfer, pipe 3 != type 1
[ 2215.713782] usb 1-1: ath9k_htc: Unable to allocate URBs
[ 2215.713801] ath9k_hif_usb: probe of 1-1:1.0 failed with error -22
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for USB dongle with device ID 3346 from IMC Networks.
Signed-off-by: Haitao Zhang <minipanda@linuxrobot.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bit 22 of AR_WA should be set to fix the situation where chip reset
is asynchronous to clock of analog shift registers, such that when
reset is released, it could mess up the values of analog shift registers
and cause some hw issue on AR9280.
This bit is write only, but the driver does a read-modify-write
on AR_WA without setting bit 22 in ar9002_hw_configpcipowersave()
during radio disable. This causes surprise removal of hw. It can
never recover from this state and the hw will become usable only
after a power on/off cycle, and sometimes only during a cold reboot.
This issue can be triggered by doing frequent roaming with the
simple/test-roam script available from the wifi-test project [1]
when roaming between APs quickly. When roaming there is a is a high
possibility that the device being put into idle (radio disable) state
by mac80211 during AUTH->ASSOC. A device hardware reset would fail
and the kernel would output:
[40251.363799] ath: AWAKE -> FULL-SLEEP
[40251.363815] ieee80211 phy17: device no longer idle - working
[40251.363817] ath: Marking phy17 as not-idle
[40251.363819] ath: FULL-SLEEP -> AWAKE
[40251.415978] pciehp 0000:00:1c.3:pcie04: Card not present on Slot(3)
[40251.419896] ath: ah->misc_mode 0x4
[40251.428138] pciehp 0000:00:1c.3:pcie04: Card present on Slot(3)
[40251.532247] ath: timeout (100000 us) on reg 0x9860: 0xffffffff & 0x00000001 != 0x00000000
[40251.532250] ath: Unable to reset channel (2462 MHz), reset status -5
[40251.532422] ath: Set channel: 5745 MHz
[40251.540639] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.548826] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.557023] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.565211] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.573415] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.581603] ath: Failed to stop TX DMA in 100 msec after killing last frame
[40251.581606] ath: Failed to stop TX DMA. Resetting hardware!
[40251.592679] ath: DMA failed to stop in 10 ms AR_CR=0xffffffff AR_DIAG_SW=0xffffffff
[40251.703330] ath: timeout (100000 us) on reg 0x7000: 0xffffffff & 0x00000003 != 0x00000000
[40251.703333] ath: RTC stuck in MAC reset
[40251.703334] ath: Chip reset failed
[40251.703335] ath: Unable to reset hardware; reset status -22
This is currently only reproducible with some HB92 (Half Mini-PCIE)
cards but the fix applies to all AR9280 cards. This patch fixes this
issue by setting bit 22 during radio disable.
This patch has fixes for all kernels that has ath9k.
[1] http://wireless.kernel.org/en/developers/Testing/wifi-test
Cc: kyungwan.nam@atheros.com
Cc: amod.bodas@atheros.com
Cc: david.quan@atheros.com
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are currently no provisions in place to ensure that the scanning
task has been stopped when the interface is stopped or removed.
This can result in a WARNING at net/wireless/core.c:643 and other badness
when you remove the module while a scan is happening.
Terminate the scanning task during interface stop.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For client STA interfaces, ieee80211_do_stop unsets the relevant
interface's SDATA_STATE_RUNNING state bit prior to cancelling an
interrupted scan. When ieee80211_offchannel_return is invoked as
part of cancelling the scan, it doesn't bother unsetting the
SDATA_STATE_OFFCHANNEL bit because it sees that the interface is
down. Normally this doesn't matter because when the client STA
interface is brought back up, it will probably issue a scan. But
in some cases (e.g., the user changes the interface type while it
is down), the SDATA_STATE_OFFCHANNEL bit will remain set. This
prevents the interface queues from being started. So we
cancel the scan before unsetting the SDATA_STATE_RUNNING bit.
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_ps_wakeup() clears the cycle counters after waking up the
hardware using ath9k_hw_setpower, however if power save is disabled,
then the counters will contain useful data, which then gets discarded.
Fix this by checking the old power mode before discarding any data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IS_ERR and PTR_ERR were called with the wrong pointer, leading to a
crash when cfg80211_get_dev_from_ifindex fails.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch includes the following updates:
* add D-Link DWA-130 Rev D
* Netgear has three WNDA3100 versions.
the original WNDA3100 is now called WNDA3100v1.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis R. Rodriguez
Rajkumar Manoharan
Vivek Natarajan
Christian Lamparter
Jussi Kivilinna
Arnd Hannemann
Wey-Yi Guy
Edgar (gimli) Hucek
Luiz Augusto von Dentz
Gustavo F. Padovan
steven miao
Matthew Garrett
Johan Hedberg
Randy Dunlap
Haitao Zhang
Vasanthakumar Thiagarajan
Daniel Drake
Brian Cavagnolo
Felix Fietkau