This adds an soc-camera / v4l2-subdev driver for the RJ54N1CB0C CMOS camera
sensor from Sharp. The sensor is very picky about initialisation and
configuration sequences. The driver limits artificially maximum window size by
800x600, although the sensor supports 1600x1200. Sizes above 800x600 don't seem
to work correctly, besides, examples from the system integrator use sizes above
640x480 only for still photography. Unfortunately, I had to use "magic"
register-value pairs for undocumented and "reserved" registers. This version of
the driver also omits some functionality, like cropping, which hasn't been
sufficiently tested yet and will be added later.
create mode 100644 drivers/media/video/rj54n1cb0c.c
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If CEU driver can not receive data from camera,
CETCR has VBP error state.
Then, CEU is stopped and cure operation is needed.
This patch add VBP error cure operation.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add comment about the meaning of the fixed JPEG header bytes used to
create each image.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The length check in reg_w_var() function is because the buffer contents
is copied to gspca_dev->usb_buf which has the size of USB_BUF_SZ bytes as
defined in drivers/media/video/gspca/gspca.h. Replace the number with
symbol for better readability and maintainability.
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert tda18271_rf_tracking_filter_cal.rf_[ab][12] from int to s32.
Convert tda18271_priv.tm_rfcal from unsigned int to u8.
Cast subtractions between u32 values as s32.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use temporary variables for signed calulations between unsigned values
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This adds a forgotten module_param macro needed to set a deemphasis of 50us.
It is the standard setting for commercial FM radio broadcasts outside the US.
Signed-off-by: Henk Vergonet <Henk.Vergonet@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
override set_frontend to allow rf input path switching on the HVR1275
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This changes adds IR Rx keypress input event handling to the CX23885 module.
This change specifically only adds input handling for IR devices implemented as
v4l2_subdevices, using only the pulse width mode (for now), and only with
RC-5 remotes. The V4L-DVB infrastructure is missing too much to support RC-6
mode 6A as used in many media center remotes. The grey Hauppauge RC-5 remote
and HVR-1850 IR receiver work now.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add integrated IR subdevice interrupt and notification handling. This is in
preparation of input keypress handling changes for the cx23885 module.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change completes the v4l2_subdev implementation for IR receive for the
IR controller built into the CX23888.
This changes almost completes the IR transmit side also, but doesn't. Instead
notes in the comments describe what needs to be done for IR Tx to work in the
subdevice implementation.
The current Tx behavior is skeletal and benign. If left alone, it does nothing.
It will only ever generate a Tx interrupt on Tx init by a caller or when the
tx_write() method is called. The ISR, when called, will then disable the Tx
FIFO service interrupt.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add v4l2_subdev_ir_ops and IR notify defines for v4l2_device. This change
is specifically needed at this time to support the integrated IR controller in
the CX2388[58] chips.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The prior mechanism wasn't reliable with the cx23887. This new mechanism
tests correctly against cx23885, 7 and 8 based products.
Signed-off-by: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For the IR controller on the CX23888 to work for the HVR-1850 and in
general, the A/V core must be initialized to get the VID_CLK going.
The VID_CLK is the timing reference for the CX23888's integrated
IR controller.
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Guennadi Liakhovetski
Kuninori Morimoto
Marton Nemeth
Rafal Milecki
Jean-Francois Moine
Michael Krufky
Henk Vergonet
Andy Walls
Steven Toth