Pull KVM fixes from Paolo Bonzini:
"Miscellaneous bugfixes.
The ARM and s390 fixes are for new regressions from the merge window,
others are usual stable material"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
compiler-gcc: disable -ftracer for __noclone functions
kvm: x86: make lapic hrtimer pinned
s390/mm/kvm: fix mis-merge in gmap handling
kvm: set page dirty only if page has been writable
KVM: x86: reduce default value of halt_poll_ns parameter
KVM: Hyper-V: do not do hypercall userspace exits if SynIC is disabled
KVM: x86: Inject pending interrupt even if pending nmi exist
arm64: KVM: Register CPU notifiers when the kernel runs at HYP
arm64: kvm: 4.6-rc1: Fix VTCR_EL2 VS setting
Pull spi fixes from Mark Brown:
"A couple of driver specific fixes here that came in since the merge
window plus one core fix for locking in cases where a client driver
grabs a lock on the whole bus for an extended series of operations
that was introduced by the changes to support accelerated flash
operations"
* tag 'spi-fix-v4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: rockchip: fix probe deferral handling
spi: omap2-mcspi: fix dma transfer for vmalloced buffer
spi: fix possible deadlock between internal bus locks and bus_lock_flag
spi: imx: Fix possible NULL pointer deref
spi: imx: only do necessary changes to ECSPIx_CONFIGREG
spi: rockchip: Spelling s/divsor/divisor/
Pull pin control fixes from Linus Walleij:
"Here is a set of pin control fixes for the v4.6 series.
A bit bigger than what I hoped for, but all fixes are confined to
drivers, a few of them also targeted to stable.
Summary:
- On Super-H PFC (Renesas) controllers: only use dummies on legacy
systems. This fixes a serious ethernet regression on a Renesas
board.
- Pistachio: Fix errors in the pin table.
- Allwinner SunXi: fix the external interrupts to work.
- Intel: fix so the high level interrupts start working, and fix a
spurious interrupt issue.
- Qualcomm ipq4019: fix the number of GPIOs provided (bump to 100),
correct register offsets and handle GPIO mode properly.
- Revert the revert on the revert so that Xway has a .to_irq()
callback again.
- Minor fixes to errorpaths and debug info.
- A MAINTAINERS update"
* tag 'pinctrl-v4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
Revert "Revert "pinctrl: lantiq: Implement gpio_chip.to_irq""
pinctrl: qcom: ipq4019: fix register offsets
pinctrl: qcom: ipq4019: fix the function enum for gpio mode
pinctrl: qcom: ipq4019: set ngpios to correct value
pinctrl: nomadik: fix pull debug print inversion
MAINTAINERS: pinctrl: samsung: Add two new maintainers
pinctrl: intel: implement gpio_irq_enable
pinctrl: intel: make the high level interrupt working
pinctrl: freescale: imx: fix bogus check of of_iomap() return value
pinctrl: sunxi: Fix A33 external interrupts not working
pinctrl: pistachio: fix mfio84-89 function description and pinmux.
pinctrl: sh-pfc: only use dummy states for non-DT platforms
Pull media fixes from Mauro Carvalho Chehab:
"Some bug fixes on au0828 and snd-usb-audio:
- the au0828+snd-usb-audio MC patch broke several things and produced
some race conditions. Better to revert the patches, and re-work on
them for a next version
- fix a regression at tuner disable links logic
- properly handle dev_state as a bitmask"
* tag 'media/v4.6-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] Revert "[media] media: au0828 change to use Managed Media Controller API"
[media] Revert "[media] sound/usb: Use Media Controller API to share media resources"
[media] au0828: Fix dev_state handling
[media] au0828: fix au0828_v4l2_close() dev_state race condition
[media] media: au0828 fix to clear enable/disable/change source handlers
[media] v4l2-mc: cleanup a warning
[media] au0828: disable tuner links and cache tuner/decoder
-ftracer can duplicate asm blocks causing compilation to fail in
noclone functions. For example, KVM declares a global variable
in an asm like
asm("2: ... \n
.pushsection data \n
.global vmx_return \n
vmx_return: .long 2b");
and -ftracer causes a double declaration.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Marek <mmarek@suse.cz>
Cc: stable@vger.kernel.org
Cc: kvm@vger.kernel.org
Reported-by: Linda Walsh <lkml@tlinx.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When a vCPU runs on a nohz_full core, the hrtimer used by
the lapic emulation code can be migrated to another core.
When this happens, it's possible to observe milisecond
latency when delivering timer IRQs to KVM guests.
The huge latency is mainly due to the fact that
apic_timer_fn() expects to run during a kvm exit. It
sets KVM_REQ_PENDING_TIMER and let it be handled on kvm
entry. However, if the timer fires on a different core,
we have to wait until the next kvm exit for the guest
to see KVM_REQ_PENDING_TIMER set.
This problem became visible after commit 9642d18ee. This
commit changed the timer migration code to always attempt
to migrate timers away from nohz_full cores. While it's
discussable if this is correct/desirable (I don't think
it is), it's clear that the lapic emulation code has
a requirement on firing the hrtimer in the same core
where it was started. This is achieved by making the
hrtimer pinned.
Lastly, note that KVM has code to migrate timers when a
vCPU is scheduled to run in different core. However, this
forced migration may fail. When this happens, we can have
the same problem. If we want 100% correctness, we'll have
to modify apic_timer_fn() to cause a kvm exit when it runs
on a different core than the vCPU. Not sure if this is
possible.
Here's a reproducer for the issue being fixed:
1. Set all cores but core0 to be nohz_full cores
2. Start a guest with a single vCPU
3. Trace apic_timer_fn() and kvm_inject_apic_timer_irqs()
You'll see that apic_timer_fn() will run in core0 while
kvm_inject_apic_timer_irqs() runs in a different core. If
you get both on core0, try running a program that takes 100%
of the CPU and pin it to core0 to force the vCPU out.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
commit 1e133ab296 ("s390/mm: split arch/s390/mm/pgtable.c") dropped
some changes from commit a3a92c31bf ("KVM: s390: fix mismatch
between user and in-kernel guest limit") - this breaks KVM for some
memory sizes (kvm-s390: failed to commit memory region) like
exactly 2GB.
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull kselftest fixes from Shuah Khan:
"This update for Kselftest contains seccomp fixes"
* tag 'linux-kselftest-4.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftest/seccomp: Fix the seccomp(2) signature
selftest/seccomp: Fix the flag name SECCOMP_FILTER_FLAG_TSYNC
Pull MIPS fixes from Ralf Baechle:
"This is the first round of MIPS fixes for 4.6:
- Fix spelling mistakes all over arch/mips
- Provide __bswapsi2 so XZ kernel compression will build with older GCC
- ATH79 clock fixes.
- Fix clock-rated copy-paste erros in ATH79 DTS.
- Fix gisb-arb compatible string for 7435 BMIPS
- Enable NAND and UBIFS support in CI20.
- Fix BUG() assertion caused by inapropriate smp_processor_id() use.
- Fix exception handling issues for the sake of debuggers
- Fix the last remaining instance of irq_to_gpio in the db1xxx_ss PCMCIA code
- Fix MSA unaligned load failures
- Panic if kernel is configured for a not TLB-supported page size
- Bail out on unsupported relocs in modules.
- Partial fix for Qemu breakage after recent IPI rewrite
- Wire up the preadv2 and pwrite2 syscalls
- Fix the ar724x clock calculation"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: traps.c: Verify the ISA for microMIPS RDHWR emulation
MIPS: BMIPS: Fix gisb-arb compatible string for 7435
MIPS: Bail on unsupported module relocs
MIPS: dts: qca: ar9132_tl_wr1043nd_v1.dts: use "ref" for reference clock name
MIPS: ath79: Fix the ar913x reference clock rate
MIPS: ath79: Fix the ar724x clock calculation
dt-bindings: clock: qca,ath79-pll: fix copy-paste typos
MIPS: traps: Correct the SIGTRAP debug ABI in `do_watch' and `do_trap_or_bp'
FIRMWARE: Broadcom: Fix grammar of warning messages in bcm47xx_sprom.c.
MIPS: ci20: Enable NAND and UBIFS support in defconfig.
MIPS: Fix misspellings in comments.
MIPS: tlb-r4k: panic if the MMU doesn't support PAGE_SIZE
MIPS: zboot: Remove copied source files on clean
MIPS: zboot: Fix the build with XZ compression on older GCC versions
MIPS: Wire up preadv2 and pwrite2 syscalls.
MIPS: cpu_name_string: Use raw_smp_processor_id().
pcmcia: db1xxx_ss: fix last irq_to_gpio user
MIPS: Fix MSA ld unaligned failure cases
MIPS: Fix broken malta qemu
Pull xen fixes from David Vrabel:
"Regression and bug fixes for 4.6-rc2:
- safely migrate event channels between CPUs
- fix CPU hotplug
- maintainer changes"
* tag 'for-linus-4.6-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: xen: Konrad to step down and Juergen to pick up
xen/events: Mask a moving irq
Xen on ARM and ARM64: update MAINTAINERS info
xen/x86: Call cpu_startup_entry(CPUHP_AP_ONLINE_IDLE) from xen_play_dead()
xen/apic: Provide Xen-specific version of cpu_present_to_apicid APIC op
Pull quota fixes from Jan Kara:
"Fixes for oopses when the new quotactl gets used with quotas disabled"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ocfs2: Fix Q_GETNEXTQUOTA for filesystem without quotas
quota: Handle Q_GETNEXTQUOTA when quota is disabled
Pull f2fs fixes from Jaegeuk Kim.
* tag 'f2fs-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs:
f2fs: retrieve IO write stat from the right place
f2fs crypto: fix corrupted symlink in encrypted case
f2fs: cover large section in sanity check of super
In commit e45708976a ("drm/dp-helper: Move the legacy helpers to
gma500") the legacy i2c helpers were moved to the only remaining user of
them, the gma500 driver. Together with that move, i2c_dp_aux_add_bus()
was marked deprecated and started warning about its remaining use.
It's now been a year and a half of annoying warning, and apparently
nobody cares enough about gma500 to try to move it along to the more
modern models.
Get rid of the warning - if even the gma500 people don't care enough,
then they should certainly not spam other innocent developers with a
warning that might hide other, much more real issues.
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge PAGE_CACHE_SIZE removal patches from Kirill Shutemov:
"PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
Let's stop pretending that pages in page cache are special. They are
not.
The first patch with most changes has been done with coccinelle. The
second is manual fixups on top.
The third patch removes macros definition"
[ I was planning to apply this just before rc2, but then I spaced out,
so here it is right _after_ rc2 instead.
As Kirill suggested as a possibility, I could have decided to only
merge the first two patches, and leave the old interfaces for
compatibility, but I'd rather get it all done and any out-of-tree
modules and patches can trivially do the converstion while still also
working with older kernels, so there is little reason to try to
maintain the redundant legacy model. - Linus ]
* PAGE_CACHE_SIZE-removal:
mm: drop PAGE_CACHE_* and page_cache_{get,release} definition
mm, fs: remove remaining PAGE_CACHE_* and page_cache_{get,release} usage
mm, fs: get rid of PAGE_CACHE_* and page_cache_{get,release} macros
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure it's the microMIPS rather than MIPS16 ISA before emulating
microMIPS RDHWR. Mostly needed as an optimisation for configurations
where `cpu_has_mmips' is hardcoded to 0 and also a good measure in case
we add further microMIPS instructions to emulate in the future, as the
corresponding MIPS16 encoding is ADDIUSP, not supposed to trap.
Signed-off-by: Maciej W. Rozycki <macro@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/12282/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I've lately been concentrating on other projects and haven't been
doing much of Xen core maintainership for the last year.
I am quite thrilled that Juergen is willing to help out!
P.S.
I am still the maintainer of Xen-SWIOTLB, Xen PCI-[front|backend],
and co-maintainer of Xen block-[front|backend]; amongst others.
Acked-by: Juergen Gross <jgross@suse.com>
Acked-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Moving an unmasked irq may result in irq handler being invoked on both
source and target CPUs.
With 2-level this can happen as follows:
On source CPU:
evtchn_2l_handle_events() ->
generic_handle_irq() ->
handle_edge_irq() ->
eoi_pirq():
irq_move_irq(data);
/***** WE ARE HERE *****/
if (VALID_EVTCHN(evtchn))
clear_evtchn(evtchn);
If at this moment target processor is handling an unrelated event in
evtchn_2l_handle_events()'s loop it may pick up our event since target's
cpu_evtchn_mask claims that this event belongs to it *and* the event is
unmasked and still pending. At the same time, source CPU will continue
executing its own handle_edge_irq().
With FIFO interrupt the scenario is similar: irq_move_irq() may result
in a EVTCHNOP_unmask hypercall which, in turn, may make the event
pending on the target CPU.
We can avoid this situation by moving and clearing the event while
keeping event masked.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Jerome Marchand
Linus Torvalds
Paolo Bonzini
Luiz Capitulino
Christian Borntraeger
Kirill A. Shutemov
Mark Brown
Maciej W. Rozycki
Florian Fainelli
Konrad Rzeszutek Wilk
Boris Ostrovsky