This is to allow number of commands reserved for use by SCSI tape drives
and medium changers to be adjusted at driver load time via the kernel
parameter cciss_tape_cmds, with a default value of 6, and a range
of 2 - 16 inclusive. Previously, the driver limited the number of
commands which could be queued to the SCSI half of the the driver
to only 2. This is to fix the problem that if you had more than
two tape drives, you couldn't, for example, erase or rewind them all
at the same time.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
It causes NMIs which are undesirable at best, unsurvivable at worst.
Prefer the soft reset instead.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
on driver load, if reset_devices is set, and the hard reset
attempts fail, try to bring up the controller to the point that
a command can be sent, and send it a soft reset command, then
after the reset undo whatever driver initialization was done to get
it to the point to take a command, and re-do it after the reset.
This is to get kdump to work on all the "non-resettable" controllers
(except 64xx controllers which can't be reset due to the potentially
shared cache module.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The bit-2-doorbell reset method seemed to cause (survivable) NMIs
on some systems and (unsurvivable) IOCK NMIs on some G7 servers.
Firmware guys implemented a new doorbell method to alleviate these
problems triggered by bit 5 of the doorbell register. We want to
use it if it's available.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When waiting for the board to become "not ready"
don't print a message saying "waiting for board to
become ready" (possibly followed by a message saying
"failed waiting for board to become not ready". Instead,
it should be "waiting for board to reset" and "failed
waiting for board to reset."
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
"
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Detect failure of controller reset by noticing if the 32 bytes of
"driver version" we store on the hardware in the config table
fail to get zeroed out. Previously we noticed if the controller
did not transition to "simple mode", but this did not detect reset
failure if the controller was already in simple mode prior to
the reset attempt (e.g. due to module parameter hpsa_simple_mode=1).
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is to ensure the board interrupts are really off when
these functions return.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
After the anticipatory scheduler was dropped, there was no need to
special-case the request_module string. As such, drop the redundant
sprintf and stack variable.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
unplug is replaced with blk_run_queue now in blk_execute_rq_nowait,
so change the comment accordingly.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Disk event code automatically blocks events on excl write. This is
primarily to avoid issuing polling commands while burning is in
progress. This behavior doesn't fit other types of devices with
removeable media where polling commands don't have adverse side
effects and door locking usually doesn't exist.
This patch introduces new genhd flag which controls the auto-blocking
behavior and uses it to enable auto-blocking only on optical devices.
Note for stable: 2.6.38 and later only
Cc: stable@kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
__blkdev_get() doesn't rescan partitions if disk->fops->open() fails,
which leads to ghost partition devices lingering after medimum removal
is known to both the kernel and userland. The behavior also creates a
subtle inconsistency where O_NONBLOCK open, which doesn't fail even if
there's no medium, clears the ghots partitions, which is exploited to
work around the problem from userland.
Fix it by updating __blkdev_get() to issue partition rescan after
-ENOMEDIA too.
This was reported in the following bz.
https://bugzilla.kernel.org/show_bug.cgi?id=13029
Note for stable: 2.6.38 and later only
Cc: stable@kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: David Zeuthen <zeuthen@gmail.com>
Reported-by: Martin Pitt <martin.pitt@ubuntu.com>
Reported-by: Kay Sievers <kay.sievers@vrfy.org>
Tested-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cdrom_open() called check_disk_change() after the rest of open path
succeeded which leads to the following bizarre behavior.
* After media change, if the device opened without O_NONBLOCK,
open_for_data() naturally fails with -ENOMEDIA and
check_disk_change() is never called. The media is known to be gone
and the open failure makes it obvious to the userland but device
invalidation never happens.
* But if the device is opened with O_NONBLOCK, all the checks are
bypassed and cdrom_open() doesn't notice that the media is not there
and check_disk_change() is called and invalidation happens.
There's nothing to be gained by avoiding calling check_disk_change()
on open failure. Common cases end up calling check_disk_change()
anyway. All we get is inconsistent behavior.
Fix it by moving check_disk_change() invocation to the top of
cdrom_open() so that it always gets called regardless of how the rest
of open proceeds.
Note for stable: 2.6.38 and later only
Cc: stable@kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Amit Shah <amit.shah@redhat.com>
Tested-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: xen-kbdfront - fix mouse getting stuck after save/restore
Input: estimate number of events per packet
Input: evdev - indicate buffer overrun with SYN_DROPPED
Input: document event types and codes and their intended use
Input: add KEY_IMAGES specifically for AL Image Browser
Input: twl4030_keypad - fix potential NULL dereference in twl4030_kp_probe()
Input: h3600_ts - fix error handling at connect
Input: twl4030_keypad - avoid potential NULL-pointer dereference
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: add blk_run_queue_async
block: blk_delay_queue() should use kblockd workqueue
md: fix up raid1/raid10 unplugging.
md: incorporate new plugging into raid5.
md: provide generic support for handling unplug callbacks.
md - remove old plugging code.
md/dm - remove remains of plug_fn callback.
md: use new plugging interface for RAID IO.
block: drop queue lock before calling __blk_run_queue() for kblockd punt
Revert "block: add callback function for unplug notification"
block: Enhance new plugging support to support general callbacks
Stephen M. Cameron
Kees Cook
Tao Ma
Tejun Heo
Linus Torvalds