This patch moves v3 pinnacle code for trackstick detection from
alps_hw_init_v3() to alps_set_protocol() so ALPS_DUALPOINT flag can be
cleared before registering trackstick input device in kernel.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds detection of trackstick for v7 protocol devices. Code in
this patch is used in official Dell touchpad linux drivers for Dell models:
Dell Latitude E5250/5250, E5450/5450, E5550/5550
Detection code and base reg for alps v3 rushmore and v7 devices is exacly
same.
Also user in bug https://bugzilla.kernel.org/show_bug.cgi?id=94801 reported
that Toshiba Sattellite Z30-A-1DG has only alps v7 touchpad device without
trackstick and kernel reports to userspace also redundant trackstick
device.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bma150_cfg structure is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We didn't check input_allocate_device() for failures so it could lead to
a NULL deref.
Fixes: 6b0f8f9c52 ('Input: add eGalaxTouch serial touchscreen driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently the user can set ff_effects_max to zero with the EV_FF bit (and
the FF_GAIN and/or FF_AUTOCENTER bits) set, in this case the uninitialized
methods ff->set_gain and/or ff->set_autocenter can be dereferenced,
resulting in a kernel oops.
Check in uinput_create_device() and print a helpful message and return
-EINVAL in case the check fails.
Signed-off-by: Elias Vanderstuyft <elias.vds@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rework the uinput ABS validation to check passed absinfo data immediately,
but do ABS initialization as last step in UI_DEV_CREATE. The behavior
observed by user-space is not changed, as ABS initialization was never
checked for errors.
With this in place, the order of device initialization and abs
configuration is no longer fixed. Userspace can initialize the device and
afterwards set absinfo just fine.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds two new ioctls, UINPUT_DEV_SETUP and UI_ABS_SETUP, that replaces
the old device setup method (by write()'ing "struct uinput_user_dev" to the
node). The old method is not easily extendable and requires huge payloads.
Furthermore, overloading write() without properly versioned objects is
error-prone.
Therefore, we introduce two new ioctls to replace the old method. These
ioctls support all features of the old method, plus a "resolution" field
for absinfo. Furthermore, it's properly forward-compatible to new ABS codes
and a growing "struct input_absinfo" structure.
UI_ABS_SETUP also allows user-space to skip unknown axes if not set. There
is no need to copy the whole array temporarily into the kernel, but instead
the caller issues several ioctl where we copy each value manually.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The goodix touchscreen driver uses a "rotated_screen" flag for
systems on which the touchscreen is mounted rotated by 180
degrees with respect to the display. With the addition of
support for the dt properties "touchscreen-inverted-x" and
"touchscreen-inverted-y", a separate "rotated_screen" flag
is not necessary anymore. This patch replaces it by setting
the inverted_x and inverted_y flags instead.
Signed-off-by: Karsten Merker <merker@debian.org>
Reviewed-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement support for the following device-tree and ACPI 5.1 DSD
properties in the goodix touchscreen driver:
- touchscreen-inverted-x: X axis is inverted (boolean)
- touchscreen-inverted-y: Y axis is inverted (boolean)
- touchscreen-swapped-x-y: X and Y axis are swapped (boolean)
These are necessary on tablets which have a display in portrait
format while the touchscreen is in landscape format, such as e.g.
the MSI Primo 81.
Signed-off-by: Karsten Merker <merker@debian.org>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Irina Tirdea <irina.tirdea@intel.com> (with ACPI DSD properties)
Tested-by: Aleksei Mamlin <mamlinav@gmail.com> (with device-tree properties)
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement suspend/resume for goodix driver.
The suspend and resume process uses the gpio pins. If the device ACPI/DT
information does not declare gpio pins, suspend/resume will not be
available for these devices.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel trees for
various devices).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Goodix devices can be configured by writing custom data to the device at
init. The configuration data is read with request_firmware from
"goodix_<id>_cfg.bin", where <id> is the product id read from the device
(e.g.: goodix_911_cfg.bin for Goodix GT911, goodix_9271_cfg.bin for
GT9271).
The configuration information has a specific format described in the Goodix
datasheet. It includes X/Y resolution, maximum supported touch points,
interrupt flags, various sensitivity factors and settings for advanced
features (like gesture recognition).
Before writing the firmware, it is necessary to reset the device. If
the device ACPI/DT information does not declare gpio pins (needed for
reset), writing the firmware will not be available for these devices.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After power on, it is recommended that the driver resets the device.
The reset procedure timing is described in the datasheet and is used
at device init (before writing device configuration) and
for power management. It is a sequence of setting the interrupt
and reset pins high/low at specific timing intervals. This procedure
also includes setting the slave address to the one specified in the
ACPI/device tree.
This is based on Goodix datasheets for GT911 and GT9271 and on Goodix
driver gt9xx.c for Android (publicly available in Android kernel
trees for various devices).
For reset the driver needs to control the interrupt and
reset gpio pins (configured through ACPI/device tree). For devices
that do not have the gpio pins properly declared, the functionality
depending on these pins will not be available, but the device can still
be used with basic functionality.
For both device tree and ACPI, the interrupt gpio pin configuration is
read from the "irq-gpios" property and the reset pin configuration is
read from the "reset-gpios" property. For ACPI 5.1, named properties
can be specified using the _DSD section. This functionality will not be
available for devices that use indexed gpio pins declared in the _CRS
section (we need to provide backward compatibility with devices
that do not support using the interrupt gpio pin as output).
For ACPI, the pins can be specified using ACPI 5.1:
Device (STAC)
{
Name (_HID, "GDIX1001")
...
Method (_CRS, 0, Serialized)
{
Name (RBUF, ResourceTemplate ()
{
I2cSerialBus (0x0014, ControllerInitiated, 0x00061A80,
AddressingMode7Bit, "\\I2C0",
0x00, ResourceConsumer, ,
)
GpioInt (Edge, ActiveHigh, Exclusive, PullNone, 0x0000,
"\\I2C0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0
}
GpioIo (Exclusive, PullDown, 0x0000, 0x0000,
IoRestrictionOutputOnly, "\\I2C0", 0x00,
ResourceConsumer, ,
)
{
1
}
})
Return (RBUF)
}
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package (2) {"irq-gpios", Package() {^STAC, 0, 0, 0 }},
Package (2) {"reset-gpios", Package() {^STAC, 1, 0, 0 }},
...
}
}
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Each of the Goodix devices supported by this driver has a fixed size for
the configuration information registers. The size varies depending on the
device and is specified in the datasheet.
Use the proper configuration length as specified in the datasheet for
each device model, so we do not read more than the actual size of the
configuration registers.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Bastien Nocera <hadess@hadess.net>
Tested-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
PS/2 protocol is slow, and using it with pass-through port (where we
encapsulate PS/2 into PS/2) is slower yet so it takes quite a bit of time
to do full protocol discovery for device attached to a pass-through port.
However, so far we have not see anything but trackpoints or basic PS/2
mice on pass-through ports, so let's limit protocols that we probe there
to Trackpoint, IntelliMouse Explorer, IntelliMouse, and bare PS/2 protocol,
and avoid other extended protocols, such as Synaptics, ALPS, etc.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation of limiting protocols that we try on pass-through ports,
let's rework initialization code and factor common code into
psmouse_try_protocol() that accepts protocol type (instead of detec()
function pointer) and can, for most protocols, perform both detection and
initialization.
Note that this removes option of forcing Lifebook protocol on devices that
are not recognized by lifebook_detect() as having the hardware, but I do
not recall anyone using this option.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When Cypress protocol support is disabled cypress_init() is a stub that
always returns -ENOSYS, so there is not point in testing for
CONFIG_MOUSE_PS2_CYPRESS after we decided that we are dealing with a
Cypress device. Also, we should only be calling cypress_detect() when
set_properties argument is "true", like with other protocols.
There is a slight change in behavior to make follow-up patches more
uniform: when we detect Cypress but its initialization fails, instead of
immediately returning PSMOUSE_PS2 protocol we now continue trying
IntelliMouse [Explorer]. Given that Cypress devices only have issue with
Sentelic probes probing Imtellimouse should be safe.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The fact that we were calling focaltech_init() even when Focaltech support
is disabled was confusing. Rearrange the code so that if support is
disabled we continue to fall through the rest of protocol probing code
until we get to full reset that Focaltech devices need to work properly.
Also, replace focaltech_init() with a stub now that it is only called when
protocol is enabled.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Marcin Sochacki <msochacki+kernel@gmail.com>
Tested-by: Till <till2.schaefer@uni-dortmund.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dan Carpenter
Dmitry Torokhov
Pali Rohár
Geliang Tang
Julia Lawall
Elias Vanderstuyft
David Herrmann
Benjamin Tissoires
Karsten Merker
Irina Tirdea