Introduce a general config option for kernel debugger hooks so that both
gdbstub and kgdb can use it and add a header file for both debuggers to use.
Signed-off-by: David Howells <dhowells@redhat.com>
The icache invalidate functions should disable the icache on AM33 and wait for
it to quiesce before attempting to invalidate it, and should then wait for it
to quiesce again before reenabling it, but on AM34 they should invalidate
directly. The same goes for the dcache invalidation, but this isn't used much.
Whilst we're at it, this can be wrapped in assembler macros to remove duplicate
code.
The AM33 manual states that:
An operation that invalidates the cache, switches the writing mode, or
changes the way mode must be performed after disabling the cache,
checking the busy bit, and confirming that the cache is not in
operation.
for the dcache [sec 2.8.3.2.1]. This is not stated so for the icache [sec
2.8.3.1.1] but the example code there suggests that it is.
Whilst the AM34 manual states that the cache must be disabled for both the
icache [sec 1.8.3.2.1] and the dcache [sec 1.8.3.2.1], the Panasonic hardware
engineers say the manual is wrong and that disabling the caches for
invalidation is wrong.
Furthermore, they say that disabling the caches on the AM34 whilst running an
SMP kernel can lead to incoherency between the various CPU caches and should
thus be avoided.
Signed-off-by: David Howells <dhowells@redhat.com>
Restrict single-stepping through the kernel using gdbstub to non-preemptable
non-SMP configs as gdbstub has to do software single-stepping by means of
temporary breakpoints. Hardware single-stepping is unavailable as Panasonic
have not sufficiently documented the interface to it.
Software single-stepping through preemptable or SMP kernels runs into problems
as it makes it much more likely that the wrong thread will hit the temporary
breakpoints. It seems impractical to work around the problem for the most
part. It could be possible to make a UP preemptable kernel switch temporary
breakpoints in and out in switch_to().
Signed-off-by: David Howells <dhowells@redhat.com>
Clear the interrupt mask registers of ASB2364 peripherals before enabling
interrupts so that any peripherals that weren't dealt with by the bootloader
after a reboot (if there was one) won't cause an interrupt storm when
interrupts are first enabled before the drivers are initialised.
Also, attempt to reset the peripherals attached to the FPGA.
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the ASB2364 gdbport UART register definitions. These registers are
actually 2 bytes apart, not 4 (which the ASB2303 and ASB2305 are).
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the definition of the ASB2364 FPGA IRQ detect registers. They accidentally
got defined to be the same as the mask registers when the patches were being
ported to the upstream kernel.
Signed-off-by: David Howells <dhowells@redhat.com>
Select HAVE_GENERIC_HARDIRQS rather than GENERIC_HARDIRQS in MN10300's main
Kconfig file to avoid this warning:
warning: (MN10300) selects GENERIC_HARDIRQS which has unmet direct dependencies (HAVE_GENERIC_HARDIRQS)
Signed-off-by: David Howells <dhowells@redhat.com>
irq_chip.end is obsolete with the removal of __do_IRQ().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Howells <dhowells@redhat.com>
mn10300 implements clocksource and clockevents and selects them
unconditionally in Kconfig. Remove the stale code which seems to be a
leftover of the conversion. Cleanup the configuration switches as well.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (27 commits)
arch/tile: support newer binutils assembler shift semantics
arch/tile: fix deadlock bugs in rwlock implementation
drivers/edac: provide support for tile architecture
tile on-chip network driver: sync up with latest fixes
arch/tile: support 4KB page size as well as 64KB
arch/tile: add some more VMSPLIT options and use consistent naming
arch/tile: fix some comments and whitespace
arch/tile: export some additional module symbols
arch/tile: enhance existing finv_buffer_remote() routine
arch/tile: fix two bugs in the backtracer code
arch/tile: use extended assembly to inline __mb_incoherent()
arch/tile: use a cleaner technique to enable interrupt for cpu_idle()
arch/tile: sync up with <arch/sim.h> and <arch/sim_def.h> changes
arch/tile: fix reversed test of strict_strtol() return value
arch/tile: avoid a simulator warning during bootup
arch/tile: export <asm/hardwall.h> to userspace
arch/tile: warn and retry if an IPI is not accepted by the target cpu
arch/tile: stop disabling INTCTRL_1 interrupts during hypervisor downcalls
arch/tile: fix __ndelay etc to work better
arch/tile: bug fix: exec'ed task thought it was still single-stepping
...
Fix up trivial conflict in arch/tile/kernel/vmlinux.lds.S (percpu
alignment vs section naming convention fix)
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (258 commits)
omap: zoom: host should not pull up wl1271's irq line
arm: plat-omap: iommu: fix request_mem_region() error path
OMAP2+: Common CPU DIE ID reading code reads wrong registers for OMAP4430
omap4: mux: Remove duplicate mux modes
omap: iovmm: don't check 'da' to set IOVMF_DA_FIXED flag
omap: iovmm: disallow mapping NULL address when IOVMF_DA_ANON is set
omap2+: mux: Fix compile when CONFIG_OMAP_MUX is not selected
omap4: board-omap4panda: Initialise the serial pads
omap3: board-3430sdp: Initialise the serial pads
omap4: board-4430sdp: Initialise the serial pads
omap2+: mux: Add macro for configuring static with omap_hwmod_mux_init
omap2+: mux: Remove the use of IDLE flag
omap2+: Add separate list for dynamic pads to mux
perf: add OMAP support for the new power events
OMAP4: Add IVA OPP enteries.
OMAP4: Update Voltage Rail Values for MPU, IVA and CORE
OMAP4: Enable 800 MHz and 1 GHz MPU-OPP
OMAP3+: OPP: Replace voltage values with Macros
OMAP3: wdtimer: Fix CORE idle transition
Watchdog: omap_wdt: add fine grain runtime-pm
...
Fix up various conflicts in
- arch/arm/mach-omap2/board-omap3evm.c
- arch/arm/mach-omap2/clock3xxx_data.c
- arch/arm/mach-omap2/usb-musb.c
- arch/arm/plat-omap/include/plat/usb.h
- drivers/usb/musb/musb_core.h
* 'for-linus' of git://codeaurora.org/quic/kernel/davidb/linux-msm: (46 commits)
msm: scm: Check for interruption immediately
msm: scm: Fix improper register assignment
msm: scm: Mark inline asm as volatile
msm: iommu: Enable HTW L2 redirection on MSM8960
msm: iommu: Don't read from write-only registers
msm: iommu: Remove dependency on IDR
msm: iommu: Use ASID tagging instead of VMID tagging
msm: iommu: Rework clock logic and add IOMMU bus clock control
msm: iommu: Clock control for the IOMMU driver
msm: mdp: Set the correct pack pattern for XRGB/ARGB
msm_fb: Fix framebuffer console
msm: mdp: Add support for RGBX 8888 image format.
video: msmfb: Put the partial update magic value into the fix_screen struct.
msm: clock: Migrate to clkdev
msm: clock: Remove references to clk_ops_pcom
msm: headsmp.S: Fix section mismatch
msm: Use explicit GPLv2 licenses
msm: iommu: Enable IOMMU support for MSM8960
msm: iommu: Generalize platform data for multiple targets
msm: iommu: Create a Kconfig item for the IOMMU driver
...
* 'devel-stable' of master.kernel.org:/home/rmk/linux-2.6-arm: (289 commits)
davinci: DM644x EVM: register MUSB device earlier
davinci: add spi devices on tnetv107x evm
davinci: add ssp config for tnetv107x evm board
davinci: add tnetv107x ssp platform device
spi: add ti-ssp spi master driver
mfd: add driver for sequencer serial port
ARM: EXYNOS4: Implement Clock gating for System MMU
ARM: EXYNOS4: Enhancement of System MMU driver
ARM: EXYNOS4: Add support for gpio interrupts
ARM: S5P: Add function to register gpio interrupt bank data
ARM: S5P: Cleanup S5P gpio interrupt code
ARM: EXYNOS4: Add missing GPYx banks
ARM: S3C64XX: Fix section mismatch from cpufreq init
ARM: EXYNOS4: Add keypad device to the SMDKV310
ARM: EXYNOS4: Update clocks for keypad
ARM: EXYNOS4: Update keypad base address
ARM: EXYNOS4: Add keypad device helpers
ARM: EXYNOS4: Add support for SATA on ARMLEX4210
plat-nomadik: make GPIO interrupts work with cpuidle ApSleep
mach-u300: define a dummy filter function for coh901318
...
Fix up various conflicts in
- arch/arm/mach-exynos4/cpufreq.c
- arch/arm/mach-mxs/gpio.c
- drivers/net/Kconfig
- drivers/tty/serial/Kconfig
- drivers/tty/serial/Makefile
- drivers/usb/gadget/fsl_mxc_udc.c
- drivers/video/Kconfig
* 'defcfg' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6647/1: add Versatile Express defconfig
ARM: 6644/1: mach-ux500: update the U8500 defconfig
* 'drivers' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6764/1: pl011: factor out FIFO to TTY code
ARM: 6763/1: pl011: add optional RX DMA to PL011 v2
ARM: 6758/1: amba: support pm ops
ARM: amba: make amba_driver id_table const
ARM: amba: make internal ID table handling const
ARM: amba: make probe() functions take const id tables
ARM: 6662/1: amba: make amba_bustype non-static
ARM: mmci: add dmaengine-based DMA support
ARM: mmci: no need for separate host->data_xfered
ARM: mmci: avoid unnecessary switch to data available PIO interrupts
ARM: mmci: no need to call flush_dcache_page() with sg_miter API
ARM: mmci: avoid reporting too many completed bytes on fifo overrun
ALSA: AACI: make fifo variables more explanitory
ALSA: AACI: no need to call snd_pcm_period_elapsed() for each period
ALSA: AACI: use snd_pcm_lib_period_bytes()
ALSA: AACI: clean up AACI announcement printk
ALSA: AACI: fix channel mask selection
ALSA: AACI: fix number of channels for record
ALSA: AACI: fix multiple IRQ claiming
* 'cyberpro-next' of master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: cyberpro: remove unused cyber2000fb_get_fb_var()
VIDEO: cyberpro: remove useless function extreg pointers
VIDEO: cyberpro: update handling of device structures
VIDEO: cyberpro: add support for video capture I2C
VIDEO: cyberpro: make 'reg_b0_lock' always present
VIDEO: cyberpro: add I2C support
VIDEO: cyberpro: select lowest multipler/divisor for PLL
* 'kvm-updates/2.6.39' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (55 commits)
KVM: unbreak userspace that does not sets tss address
KVM: MMU: cleanup pte write path
KVM: MMU: introduce a common function to get no-dirty-logged slot
KVM: fix rcu usage in init_rmode_* functions
KVM: fix kvmclock regression due to missing clock update
KVM: emulator: Fix permission checking in io permission bitmap
KVM: emulator: Fix io permission checking for 64bit guest
KVM: SVM: Load %gs earlier if CONFIG_X86_32_LAZY_GS=n
KVM: x86: Remove useless regs_page pointer from kvm_lapic
KVM: improve comment on rcu use in irqfd_deassign
KVM: MMU: remove unused macros
KVM: MMU: cleanup page alloc and free
KVM: MMU: do not record gfn in kvm_mmu_pte_write
KVM: MMU: move mmu pages calculated out of mmu lock
KVM: MMU: set spte accessed bit properly
KVM: MMU: fix kvm_mmu_slot_remove_write_access dropping intermediate W bits
KVM: Start lock documentation
KVM: better readability of efer_reserved_bits
KVM: Clear async page fault hash after switching to real mode
KVM: VMX: Initialize vm86 TSS only once.
...
* 'stable/xen.pm.bug-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: use freeze/restore/thaw PM events for suspend/resume/chkpt
xen: xenbus PM events support
* 'stable/irq.fairness' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: events: Remove redundant clear of l2i at end of round-robin loop
xen: events: Make round-robin scan fairer by snapshotting each l2 word once only
xen: events: Clean up round-robin evtchn scan.
xen: events: Make last processed event channel a per-cpu variable.
xen: events: Process event channels notifications in round-robin order.
* 'stable/irq.ween_of_nr_irqs' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: events: Fix compile error if CONFIG_SMP is not defined.
xen: events: correct locking in xen_irq_from_pirq
xen: events: propagate irq allocation failure instead of panicking
xen: events: do not workaround too-small nr_irqs
xen: events: remove use of nr_irqs as upper bound on number of pirqs
xen: events: dynamically allocate irq info structures
xen: events: maintain a list of Xen interrupts
xen: events: push setup of irq<->{evtchn,ipi,virq,pirq} maps into irq_info init functions
xen: events: turn irq_info constructors into initialiser functions
xen: events: use per-cpu variable for cpu_evtchn_mask
xen: events: refactor GSI pirq bindings functions
xen: events: rename restore_cpu_pirqs -> restore_pirqs
xen: events: remove unused public functions
xen: events: fix xen_map_pirq_gsi error return
xen: events: simplify comment
xen: events: separate two unrelated halves of if condition
Fix up trivial conflicts in drivers/xen/events.c
David Howells
Thomas Gleixner
Linus Torvalds