A little class that keeps track of the volume of io that is in flight,
and the length of time that a device has been idle for.
FIXME: rather than jiffes, may be best to use ktime_t (to support faster
devices).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There is a race between a policy deciding to replace a cache entry,
the core target writing back any dirty data from this block, and other
IO threads doing IO to the same block.
This sort of problem is avoided most of the time by the core target
grabbing a bio prison cell before making the request to the policy.
But for a demotion the core target doesn't know which block will be
demoted, so can't do this in advance.
Fix this demotion race by introducing a callback to the policy interface
that allows the policy to grab the cell on behalf of the core target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
A crypto driver can process requests synchronously or asynchronously
and can use an internal driver queue to backlog requests.
Add some comments to clarify internal logic and completion return codes.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Currently if there is a leg failure, the bio will be put into the hold
list until userspace does a remove/replace on the leg. Doing so in a
cluster config (clvmd) is problematic because there may be a temporary
path failure that results in cluster raid1 remove/replace. Such
recovery takes a long time due to a full resync.
Update dm-raid1 to optionally ignore these failures so bios continue
being issued without interrupton. To enable this feature userspace
must pass "keep_log" when creating the dm-raid1 device.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Tested-by: Liuhua Wang <lwang@suse.com>
Acked-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
On 32-bit:
drivers/md/dm-log-writes.c: In function ‘log_super’:
drivers/md/dm-log-writes.c:323: warning: integer constant is too large for ‘long’ type
Add a ULL suffix to WRITE_LOG_MAGIC to fix this.
Also add a ULL suffix to WRITE_LOG_VERSION as it's stored in a __le64
field.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add dm-raid access to the MD RAID0 personality to enable single zone
striping.
The following changes enable that access:
- add type definition to raid_types array
- make bitmap creation conditonal in super_validate(), because
bitmaps are not allowed in raid0
- set rdev->sectors to the data image size in super_validate()
to allow the raid0 personality to calculate the MD array
size properly
- use mdddev(un)lock() functions instead of direct mutex_(un)lock()
(wrapped in here because it's a trivial change)
- enhance raid_status() to always report full sync for raid0
so that userspace checks for 100% sync will succeed and allow
for resize (and takeover/reshape once added in future paches)
- enhance raid_resume() to not load bitmap in case of raid0
- add merge function to avoid data corruption (seen with readahead)
that resulted from bio payloads that grew too large. This problem
did not occur with the other raid levels because it either did not
apply without striping (raid1) or was avoided via stripe caching.
- raise version to 1.7.0 because of the raid0 API change
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- ensure maximum device limit in superblock
- rename DMPF_* (print flags) to CTR_FLAG_* (constructor flags)
and their respective struct raid_set member
- use strcasecmp() in raid10_format_to_md_layout() as in the constructor
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Remove comment above parse_raid_params() that claims
"devices_handle_discard_safely" is a table line argument when it is
actually is a module parameter.
Also, backfill dm-raid target version 1.6.0 documentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Reviewed-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Leverage the block manager's read_only flag instead of duplicating it;
access with new dm_bm_is_read_only() method.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The overwrite has only ever about optimizing away the need to zero a
block if the entire block was being overwritten. As such it is only
relevant when zeroing is enabled.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Introduce a single common method for cleaning up a DM device's
mapped_device. No functional change, just eliminates duplication of
delicate mapped_device cleanup code.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
More often than not a request that is requeued _is_ mapped (meaning the
clone request is allocated and clone->q is initialized). Rename
dm_requeue_unmapped_original_request() to avoid potential confusion due
to function name containing "unmapped".
Also, remove dm_requeue_unmapped_request() since callers can easily call
the dm_requeue_original_request() directly.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Do not allocate the io_pool mempool for blk-mq request-based DM
(DM_TYPE_MQ_REQUEST_BASED) in dm_alloc_rq_mempools().
Also refine __bind_mempools() to have more precise awareness of which
mempools each type of DM device uses -- avoids mempool churn when
reloading DM tables (particularly for DM_TYPE_REQUEST_BASED).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm_merge_bvec() was originally added in f6fccb ("dm: introduce
merge_bvec_fn"). In that commit a value in sectors is converted to
bytes using << 9, and then assigned to an int. This code made
assumptions about the value of BIO_MAX_SECTORS.
A later commit 148e51 ("dm: improve documentation and code clarity in
dm_merge_bvec") was meant to have no functional change but it removed
the use of BIO_MAX_SECTORS in favor of using queue_max_sectors(). At
this point the cast from sector_t to int resulted in a zero value. The
fallout being dm_merge_bvec() would only allow a single page to be added
to a bio.
This interim fix is minimal for the benefit of stable@ because the more
comprehensive cleanup of passing a sector_t to all DM targets' merge
function will impact quite a few DM targets.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.19+
dm-multipath accepts 0 path mapping.
# echo '0 2097152 multipath 0 0 0 0' | dmsetup create newdev
Such a mapping can be used to release underlying devices while still
holding requests in its queue until working paths come back.
However, once the multipath device is created over blk-mq devices,
it rejects reloading of 0 path mapping:
# echo '0 2097152 multipath 0 0 1 1 queue-length 0 1 1 /dev/sda 1' \
| dmsetup create mpath1
# echo '0 2097152 multipath 0 0 0 0' | dmsetup load mpath1
device-mapper: reload ioctl on mpath1 failed: Invalid argument
Command failed
With following kernel message:
device-mapper: ioctl: can't change device type after initial table load.
DM tries to inherit the current table type using dm_table_set_type()
but it doesn't work as expected because of unnecessary check about
whether the target type is hybrid or not.
Hybrid type is for targets that work as either request-based or bio-based
and not required for blk-mq or non blk-mq checking.
Fixes: 65803c2059 ("dm table: train hybrid target type detection to select blk-mq if appropriate")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When stacking request-based dm device on non blk-mq device and
device-mapper target could not map the request (error target is used,
multipath target with all paths down, etc), the WARN_ON_ONCE() in
free_rq_clone() will trigger when it shouldn't.
The warning was added by commit aa6df8d ("dm: fix free_rq_clone() NULL
pointer when requeueing unmapped request"). But free_rq_clone() with
clone->q == NULL is valid usage for the case where
dm_kill_unmapped_request() initiates request cleanup.
Fix this false warning by just removing the WARN_ON -- it only generated
false positives and was never useful in catching the intended case
(completing clone request not being mapped e.g. clone->q being NULL).
Fixes: aa6df8d ("dm: fix free_rq_clone() NULL pointer when requeueing unmapped request")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use BLK_MQ_RQ_QUEUE_BUSY to requeue a blk-mq request directly from the
DM blk-mq device's .queue_rq. This cleans up the previous convoluted
handling of request requeueing that would return BLK_MQ_RQ_QUEUE_OK
(even though it wasn't) and then run blk_mq_requeue_request() followed
by blk_mq_kick_requeue_list().
Also, document that DM blk-mq ontop of old request_fn devices cannot
fail in clone_rq() since the clone request is preallocated as part of
the pdu.
Reported-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When stacking request-based DM on blk_mq device, request cloning and
remapping are done in a single call to target's clone_and_map_rq().
The clone is allocated and valid only if clone_and_map_rq() returns
DM_MAPIO_REMAPPED.
The "IS_ERR(clone)" check in map_request() does not cover all the
!DM_MAPIO_REMAPPED cases that are possible (E.g. if underlying devices
are not ready or unavailable, clone_and_map_rq() may return
DM_MAPIO_REQUEUE without ever having established an ERR_PTR). Fix this
by explicitly checking for a return that is not DM_MAPIO_REMAPPED in
map_request().
Without this fix, DM core may call setup_clone() for a NULL clone
and oops like this:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000068
IP: [<ffffffff81227525>] blk_rq_prep_clone+0x7d/0x137
...
CPU: 2 PID: 5793 Comm: kdmwork-253:3 Not tainted 4.0.0-nm #1
...
Call Trace:
[<ffffffffa01d1c09>] map_tio_request+0xa9/0x258 [dm_mod]
[<ffffffff81071de9>] kthread_worker_fn+0xfd/0x150
[<ffffffff81071cec>] ? kthread_parkme+0x24/0x24
[<ffffffff81071cec>] ? kthread_parkme+0x24/0x24
[<ffffffff81071fdd>] kthread+0xe6/0xee
[<ffffffff81093a59>] ? put_lock_stats+0xe/0x20
[<ffffffff81071ef7>] ? __init_kthread_worker+0x5b/0x5b
[<ffffffff814c2d98>] ret_from_fork+0x58/0x90
[<ffffffff81071ef7>] ? __init_kthread_worker+0x5b/0x5b
Fixes: e5863d9ad ("dm: allocate requests in target when stacking on blk-mq devices")
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.0+
Without kicking queue, requeued request may stay forever in
the queue if there are no other I/O activities to the device.
The original error had been in v2.6.39 with commit 7eaceaccab
("block: remove per-queue plugging"), which replaced conditional
plugging by periodic runqueue.
Commit 9d1deb83d4 in v4.1-rc1 removed the periodic runqueue
and the problem started to manifest.
Fixes: 9d1deb83d4 ("dm: don't schedule delayed run of the queue if nothing to do")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Joe Thornber
Milan Broz
Lidong Zhong
Geert Uytterhoeven
Luis Henriques
Heinz Mauelshagen
Mike Snitzer
Junichi Nomura
Julia Lawall
Linus Torvalds