Firmware loading may reset the controller UART speed and needs to set
host UART speed back to init speed.
UART drivers setup is split in 3 parts:
- btbcm_initialize() resets the controller and returns the firmware
name based on controller revision and sub_version.
- btbtcm_patchram() (already existing and public), which takes the
firmware name as parameter, requests the firmware and loads it to
the controller.
- btbcm_finalize() which resets the controller, reads local version
and checks if the controller address is a default one or not.
Remove firmware name retrieval for UART controllers from
btbcm_setup_patchram().
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add initial and operational speeds.
Change to operational speed as soon as possible. If controller
set_baudrate() fails, continue at initial speed.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Move request/release_firmware() out of btbcm_patchram().
This allows a better error management, if request_firmware() returns an
error then the controller will be used without firmware loading and 0 is
returned.
This will imply to change btbcm_patchram() to accept a firmware instead
of firmware name.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch will export the supported commands by the devices
to the userspace. This will be useful to check if HardMAC
drivers can support a specific command or not.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The AF_IEEE802154 sockaddr looks like this:
struct sockaddr_ieee802154 {
sa_family_t family; /* AF_IEEE802154 */
struct ieee802154_addr_sa addr;
};
struct ieee802154_addr_sa {
int addr_type;
u16 pan_id;
union {
u8 hwaddr[IEEE802154_ADDR_LEN];
u16 short_addr;
};
};
On most architectures there will be implicit structure padding here,
in two different places:
* In struct sockaddr_ieee802154, two bytes of padding between 'family'
(unsigned short) and 'addr', so that 'addr' starts on a four byte
boundary.
* In struct ieee802154_addr_sa, two bytes at the end of the structure,
to make the structure 16 bytes.
When calling recvmsg(2) on a PF_IEEE802154 SOCK_DGRAM socket, the
ieee802154 stack constructs a struct sockaddr_ieee802154 on the
kernel stack without clearing these padding fields, and, depending
on the addr_type, between four and ten bytes of uncleared kernel
stack will be copied to userspace.
We can't just insert two 'u16 __pad's in the right places and zero
those before copying an address to userspace, as not all architectures
insert this implicit padding -- from a quick test it seems that avr32,
cris and m68k don't insert this padding, while every other architecture
that I have cross compilers for does insert this padding.
The easiest way to plug the leak is to just memset the whole struct
sockaddr_ieee802154 before filling in the fields we want to fill in,
and that's what this patch does.
Cc: stable@vger.kernel.org
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch make to use the same naming convention that mac802154
tracing follows and fixes the format specifier for extended addr.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch sets the acknowledge request bit inside the 802.15.4 mac
header when frame retries is 0 or above. The other frame retries value
which is -1 indicates that the transmitter doesn't care about an
acknowledge frame which will be ignored after transmitting if the node
sends anyway an ack frame after receiving. This is currently unnecessary
traffic if the max frame retries parameter is -1.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the current channel to 11. This is the default
value on reset.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
CC2520 has the default 0dBm transmit power level on reset.
This patch update initial value of transmit power with 0dBm value.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for seeting tx power values for cc2520
and also for the combination of CC2520-CC2591.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch changes tha way of handling of cc2591-cc2520 combination
by moving amplified variable from platform data to private data.
This will be useful in other sections like tx power support.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Initially we dont have the tx power settings from the user-space.
Now we have the support for seeting the tx power level.
So lets use the default tx power setting for the radio.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Cc: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With this function we can set individual bits in the registers if needed.
With the old SR_VALUE macro we could only set one bit in the register
which was ok for some scenarios but not for all. With this subreg write
function we can now set more bits defined by the mask while not touching
the rest.
We start using it for the current SR_VALUE use case and will use it more
in upcoming patches.
Signed-off-by: Stefan Schmidt <stefan@osg.samsung.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Refuse to allow setting an EUI-64 group address as an interface
address, as those are not valid station addresses.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Currently, ieee802154_random_extended_addr() has a 50% chance of
generating a group (multicast) address, while this function is used
for generating station addresses (which can't be group addresses)
for interfaces that don't have a hardware-provided address.
Also, in case get_random_bytes() generates the EUI-64 address
00:00:00:00:00:00:00:00 (extremely unlikely), which is an invalid
address, ieee802154_random_extended_addr() reacts by changing it
to 01:00:00:00:00:00:00:00, which is an invalid station address as
well, as it is a group address.
This patch changes the address generation procedure to grab eight
random bytes, treat that as an EUI-64, and then clear the Group
address bit and set the Locally Administered bit, which is in
line with how eth_random_addr() generates random EUI-48s.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Antonio Quartulli says:
====================
Included changes:
- checkpatch fixes
- code cleanup
- debugfs component is now compiled only if DEBUG_FS is selected
- update copyright years
- disable by default not-so-user-safe features
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Normally the program attachment place (like sockets, qdiscs) takes
care of rcu protection and calls bpf_prog_put() after a grace period.
The programs stored inside prog_array may not be attached anywhere,
so prog_array needs to take care of preserving rcu protection.
Otherwise bpf_tail_call() will race with bpf_prog_put().
To solve that introduce bpf_prog_put_rcu() helper function and use
it in 3 places where unattached program can decrement refcnt:
closing program fd, deleting/replacing program in prog_array.
Fixes: 04fd61ab36 ("bpf: allow bpf programs to tail-call other bpf programs")
Reported-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
K. Y. Srinivasan says:
====================
hv_netvsc: Implement NUMA aware memory allocation
Allocate both receive buffer and send buffer from the NUMA node assigned to the
primary channel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Frederic Danis
Varka Bhadram
Lennert Buytenhek
Prasanna Karthik
Alexander Aring
Stefan Schmidt
David S. Miller
Alexei Starovoitov
K. Y. Srinivasan