PULL_PIN_DEFAULT is meant for hardware completely hiding any pull
settings from the driver, so that it's really only possible to turn
the pull on or off, but it not being possible to determine any
pull settings from software.
Also the binding-documentation for the pull arguments did not match
the changes to the expected values.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
From the inception ot the pin config API there has been the
possibility to get a handle at a pin directly and configure
its electrical characteristics. For this reason we had:
int pin_config_get(const char *dev_name, const char *name,
unsigned long *config);
int pin_config_set(const char *dev_name, const char *name,
unsigned long config);
int pin_config_group_get(const char *dev_name,
const char *pin_group,
unsigned long *config);
int pin_config_group_set(const char *dev_name,
const char *pin_group,
unsigned long config);
After the introduction of the pin control states that will
control pins associated with devices, and its subsequent
introduction to the device core, as well as the
introduction of pin control hogs that can set up states on
boot and optionally also at sleep, this direct pin control
API is a thing of the past.
As could be expected, it has zero in-kernel users.
Let's delete this API and make our world simpler.
Reported-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a pin control driver for the TZ1090's low power pins via the
powerdown controller SOC_GPIO_CONTROL registers.
These pins have individually controlled pull-up, and group controlled
schmitt, slew-rate, drive-strength, and power-on-start (pos).
The pdc_gpio0 and pdc_gpio1 pins can also be muxed onto the
ir_mod_stable_out and ir_mod_power_out functions respectively. If no
function is set they remain in GPIO mode. These muxes can be overridden
by requesting them as GPIOs.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At several places, return value was not tested
and error output was missing.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- allow to get output GPIO value
- as there is no GPIO0 on ABX500, use correct offset with
abx500_gpio_get_bit()
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Update abx500_pin_config_set() in order to take in
account PIN_CONFIG_BIAS_DISABLE state to disable
pull up or pull down.
- Rework error path.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use the same way to define pin muxing and pin configuration
than for nomadik. So pickup code from pinctrl_nomadik.c to be
able to implement pin multiplexing and pin configuration using
the device tree. Pin configuration uses generic parsing code.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix a compilation error caused by pinconf_generic_parse_dt_config() not
being defined on !CONFIG_OF platforms by guarding the whole DT node
parsing code with #ifdef CONFIG_OF.
Defining a pinconf_generic_parse_dt_config() on !CONFIG_OF would have
been possible as well, but would have resulted in a larger code size on
!CONFIG_OF platforms (such as arch/sh).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for gpio on Intel BayTrail platforms. BayTrail supports 3 banks
of gpios called SCORE, NCORE ans SUS with 102, 28 and 44 gpio pins.
Supports gpio interrupts and ACPI gpio events
Pins may be muxed to alternate function instead of gpio by firmware.
This driver does not touch the pin muxing and expect firmare
to set pin muxing and pullup/down properties properly.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The kerneldoc comment for struct pinconf_ops was missing
pin_config_dbg_parse_modify, and instead described
pin_config_group_dbg_set (which is presumably an old name for the same
function). Rename it in the kerneldoc comment so they match.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the missing unlock before return from function pinctrl_find_gpio_range_from_pin()
in the error handling case.
Introduced by commit 2ff3477efd7086544b9e298fc63afab0645921b4.
(pinctrl: add pin list based GPIO ranges)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A level-triggered interrupt should be acked after the interrupt line
becomes inactive and before it is unmasked, or else another interrupt
will be immediately triggered. Acking before or after calling the
handler is not enough.
Signed-off-by: Luigi Semenzato <semenzato@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Heiko Stübner
Linus Walleij
James Hogan
Sachin Kamat
Axel Lin
Patrice Chotard
Laurent Pinchart
Mathias Nyman
Wei Yongjun
Doug Anderson