PORT_HOTPLUG_EN has allready been setup in i915_driver_irq_postinstall(),
when intel_dp_detect() runs.
Delete the DP[BCD]_HOTPLUG_INT_EN defines, they are not referenced anymore.
I found this while searching for a fix for
https://bugzilla.redhat.com/show_bug.cgi?id=528312
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: Eric Anholt <eric@anholt.net>
This should be a small power savings. Tested on Lenovo T410 (Ironlake), LVDS
VGA and DisplayPort, up to 1920x1200R.
v2: Add Sandybridge support, fix obvious math error.
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Update the self-refresh watermark for display plane/cursor and enable
the memory self-refresh on Ironlake. The watermark is also updated for
the active display plane.
More than 1W idle power is saved on one Ironlake laptop after enabling
memory self-refresh.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Previously, after setting up the Pineview CxSR state, i9xx_update_wm would
get called and overwrite our state.
BTW: We will disable the self-refresh and never enable it any more if we
can't find the appropriate the latency on pineview plaftorm. In such case
the update_wm callback will be NULL.
The bitmask macro is also defined to access the corresponding fifo
watermark register.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
SDVO on Ibexpeak PCH with Ironlake is multiplexed with
HDMIB port, and only has SDVOB port.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The existing code handling the DPMS ON event is much more careful to
ensure that these registers are enabled according to strict sequencing
requirements. Enabling these early in mode_set simply defeats that.
Signed-off-by: Carl Worth <cworth@cworth.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
->dev_private at that point is NULL and is initialied only a few lines
later.
Signed-off-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This reverts commit 6070a4a928.
The quirk for this SDVO device on IBM specific board is just a hack
in old code which showed the broken multifunction SDVO support in
the driver. Multifunction SDVO patch provided the right fix for it.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
With new intel_encoder/intel_connector structure change, each supported
connector type on SDVO device will be created as a new 'intel_connector',
and all attached to one 'intel_encoder' for its SDVO port.
The SDVO encoder will handle SDVO protocol stuff, and each connector does
its own part of work now, like detection is only to check if current active
output is itself, etc.
Update since last submit:
- Fixed SDVO TV property creation failure by incorrect set target output call
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
As all display drivers have been converted, remove the left reference
for connector object in old structure.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Probably only matters for format-converting dongles, but might as well
get it right all the time.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
DP on Cougarpoint has new training pattern definitions, and
new transcoder DP control register is used to determine the mapping
for transcoder and DP digital output. And eDP for Sandybridge has
new voltage and pre-emphasis level definitions.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Karsten Wiese
Adam Jackson
Zhenyu Wang
Zhao Yakui
Carl Worth
Luca Tettamanti