Add some more chip IDs to bcma_pmu_get_alp_clock()
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hard coding these values use the existing constants.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The messages are currently hard coding "1ms", which does not match
the actual timeout being used.
Signed-off-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marco Fonseca reported a issue with his carl9170 device:
"I'm seeing a problem with the carl driver. If I change channels
repeatedly on the 2.4ghz band, monitoring (e.g. tcpdump) will
eventually halt. I've seen this on various versions of the carl
driver/firmware (both from 1.9.4 to 1.9.7)"
<http://marc.info/?l=linux-wireless&m=136381302428113>
The culprit was identified as "fast channel change feature" which
according to Adrian Chadd is: "... notoriously unreliable and
really only fully debugged on some very later chips."
<http://marc.info/?l=linux-wireless&m=136416984531380>
Therefore, this patch removes the fast channel change feature.
The phy will now always have to go through a cold reset when
changing channels, but it should no longer become deaf.
Cc: Marco Fonseca <marco@tampabay.rr.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix settings not being applied when the device is idle and the firmware
gets reloaded (because of changing from STA to AP mode). This caused
the device using the wrong channel (and likely band), e.g. a 5 GHz only
card still defaulted to channel 6 in the 2.4 GHz band when left
unconfigured.
This issue was always present, but only made visible with "mwl8k: Do not
call mwl8k_cmd_set_rf_channel unconditionally" (0f4316b9), since before
that the channel was (re-)configured at the next _config call even when
it did not change from the mac80211 perspective.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible to configure the ucode to automatically send the probe
responses to the clients after they send a probe request. At least for
WPS the userspace needs to answer the probe requests and we do not know
a way to say to the ucode to just handle the normal probe requests, so
for now no probe requests should be handled by the ucode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ucode is able to answer probe response by itself. This writes such
a template into the specific memory. Currently the probe requests are
also send to mac80211 so there are more answers send to a requesting
client. We have to make the ucode stop sending probe requests to the
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To send the correct probe response the hardware needs to know the SSID
when it changed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it possible that a beacon template provided by mac80211 is
written to the hardware for constant beaconing.
This is based on an old version of brcmsmac, on b43 and the spec b43 is
based on.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make brcms_c_set_beacon_period() write the beacon period to the
hardware if a new one is set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was a read only member, replace it with pub->up.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was a read only member. The checks using BSS are replaced by
better fitting checks of the new type member.
The change in brcms_c_tbtt() was based on code from b43, in
brcms_c_ps_allowed() the same happens with BSS being true or false,
beaconing and probe responses are just needed in ap mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it possible to easily check in which mode the device is
currently running. This also adds a function to start station mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
setting the tsf is needed to start a timer to make beaconing in AP mode
work.
This is based on older versions of brcmsmac and b43.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of defining the magic values in the code use constants.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FW can be woken up even by accessing device registers; we need
not explicitily enable interrupts for doing this. Future PCIe
devices will not be woken up by writing to host registers.
This patch enables driver to wake up device by reading FW status
register.
Also devices with sleep cookie enabled need some more time before
proceeding with processing. Handle this by adding a delay loop.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have received interrupt from device means FW is not sleeping.
In this case make sure wakeup handler for PCIe is not invoked by
setting adapter->pm_wakeup_fw_try to false.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hauke Mehrtens
Robert Shade
Christian Lamparter
Jonas Gorski
Avinash Patil