Add a function to map a given resource number to a corresponding
register so drivers can get the offset and type of device specific BARs.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Allow pci_alloc_child_bus() to allocate buses without bridge devices.
Some SR-IOV devices can occupy more than one bus number, but there is no
explicit bridges because that have internal routing mechanism.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Export __pci_read_base() so it can be used by whole PCI subsystem.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Remove the unnecessary number of resources condition checks because
the pci_update_resource() will check availability of the resources.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch moves all definitions of the PCI resource names to an 'enum',
and also replaces some hard-coded resource variables with symbol
names. This change eases introduction of device specific resources.
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This cleanup removes unnecessary argument 'struct resource *res' in
pci_update_resource(), so it takes same arguments as other companion
functions (pci_assign_resource(), etc.).
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change parameter of pci_ari_enabled() from 'pci_dev' to 'pci_bus'.
ARI forwarding on the bridge mostly concerns the subordinate devices
rather than the bridge itself. So this change will make the function
easier to use.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
PCI devices have three settable boolean attributes, enable,
broken_parity_status, and msi_bus.
The store functions for these would silently interpret "0x01" as false,
"1llogical" as true, and "true" would be (silently!) ignored and do
nothing.
This is inconsistent with typical sysfs handling of settable attributes,
and just plain doesn't make much sense.
So, use strict_strtoul(), which was created for this purpose. The store
functions will treat a value of 0 as false, non-zero as true, and return
-EINVAL for a parse failure.
Additionally, is_enabled_store() and msi_bus_store() return -EPERM if
CAP_SYS_ADMIN is lacking, rather than silently doing nothing. This is more
typical behavior for sysfs attributes that need a capability.
And msi_bus_store() will only print the "forced subordinate bus ..."
warning if the MSI flag was actually forced to a different value.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch (as1186) fixes a minor mistake in pci_enable_wake(). When
the routine is asked to disable remote wakeup, it should not return an
error merely because the device is not allowed to do wakeups!
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds pci_swizzle_interrupt_pin(), which implements the
INTx swizzling algorithm specified in Table 9-1 of the "PCI-to-PCI
Bridge Architecture Specification," revision 1.2.
There are many architecture-specific implementations of this
swizzle that can be replaced by this common one.
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Keep "pin" encoded as it is in the "Interrupt Pin" value in PCI config
space, i.e., 0=device doesn't use interrupts, 1=INTA, ..., 4=INTD.
This makes the bridge INTx swizzle match other architectures.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes pci_get_interrupt_pin() return values encoded
the same way as the "Interrupt Pin" value in PCI config space,
i.e., 1=INTA, ..., 4=INTD.
pirq_bios_set() is the only in-tree caller of pci_get_interrupt_pin()
and pci_get_interrupt_pin() is not exported.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch changes cpqphp to use interrupt pin values just as they
come from PCI config space, i.e., 1=INTA, ..., 4=INTD.
pcibios_set_irq_routing() takes pin arguments in the range 0=INTA, ...,
3=INTD, so we'll adjust the pin just before calling it.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Early type 1 accesses can cause problems on some platforms, and
pci=noearly is supposed to prevent them from occurring. However, early
mcfg probing code uses type 1 and isn't protected by a check for
noearly. This patch fixes that problem.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These printks don't contain enough information to be useful. I think it
would be more useful to have a message when a service driver binds to a
root port. That could contain the service type, the interrupt mode and
IRQ, etc.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Yu Zhao
Adam Jackson
Trent Piepho
Andrew Morton
Alan Stern
Bjorn Helgaas
Jacob Pan