Playing with the VLAN map of every port to implement "hardware bridging"
in the 88E6352 driver was a hack until full 802.1Q was supported.
Indeed with 802.1Q port mode "Disabled" or "Fallback", this feature is
used to restrict which output ports an input port can egress frames to.
A Linux bridge is an untagged VLAN. With full 802.1Q support, we don't
need this hack anymore and can use the "Secure" strict 802.1Q port mode.
With this mode, the port-based VLAN map still needs to be configured,
but all the logic is VTU-centric. This means that the switch only cares
about rules described in its hardware VLAN table, which is exactly what
Linux bridge expects and what we want.
Note also that the hardware bridging was broken with the previous
flexible "Fallback" 802.1Q port mode. Here's an example:
Port0 and Port1 belong to the same bridge. If Port0 sends crafted tagged
frames with VID 200 to Port1, Port1 receives it. Even if Port1 is in
hardware VLAN 200, but not Port0, Port1 will still receive it, because
Fallback mode doesn't care about invalid VID or non-member source port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A DSA driver may not provide the port_join_bridge and port_leave_bridge
functions, so don't warn in such case.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we configure a switch chip through a Linux bridge, and a bridge is
implemented as a VLAN, there is no need for per-port FID anymore.
This patch gets rid of this and simplifies the driver code since we can
now directly map all 4095 FIDs available to all VLANs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With 88E6352 and similar switch chips, each port has a map to restrict
which output port this input port can egress frames to.
The current driver code implements hardware bridging using this feature,
and assigns to a bridge group the FID of its first member.
Now that 802.1Q is fully implemented in this driver, a Linux bridge
which is a simple untagged VLAN, already gets its own FID.
This patch gets rid of the per-bridge FID and explicits the usage of the
port based VLAN map feature.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the following "duelling syn" sequence between two peers A and B:
A B
SYN1 -->
<-- SYN2
SYN2ACK -->
Note that the SYN/ACK has already been sent out by TCP before
rds_tcp_accept_one() gets invoked as part of callbacks.
If the inet_addr(A) is numerically less than inet_addr(B),
the arbitration scheme in rds_tcp_accept_one() will prefer the
TCP connection triggered by SYN1, and will send a CLOSE for the
SYN2 (just after the SYN2ACK was sent).
Since B also follows the same arbitration scheme, it will send the SYN-ACK
for SYN1 that will set up a healthy ESTABLISHED connection on both sides.
B will also get a CLOSE for SYN2, which should result in the cleanup
of the TCP state machine for SYN2, but it should not trigger any
stale RDS-TCP callbacks (such as ->writespace, ->state_change etc),
that would disrupt the progress of the SYN2 based RDS-TCP connection.
Thus the arbitration scheme in rds_tcp_accept_one() should restore
rds_tcp callbacks for the winner before setting them up for the
new accept socket, and also make sure that conn->c_outgoing
is set to 0 so that we do not trigger any reconnect attempts on the
passive side of the tcp socket in the future, in conformance with
commit c82ac7e69e ("net/rds: RDS-TCP: only initiate reconnect attempt
on outgoing TCP socket.")
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP address passed to rds_bind() should be vetted by the
transport's ->laddr_check() for a previously bound transport.
This needs to be done to avoid cases where, for example,
the application has asked for an IB transport,
but the IP address passed to bind is only usable on
ethernet interfaces.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only instance of a qlcnic_mbx_ops structure is never modified. Thus
the declaration of the structure and all references to the structure type
can be made const.
In the definition of the qlcnic_mailbox structure, the ops field is no
longer lined up with the other fields. This was left as is, to avoid a lot
of trivial changes on the other lines.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it's possible for someone to send a vlan range to the kernel
with the pvid flag set which will result in the pvid bouncing from a
vlan to vlan and isn't correct, it also introduces problems for hardware
where it doesn't make sense having more than 1 pvid. iproute2 already
enforces this, so let's enforce it on kernel-side as well.
Reported-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a smatch warning:
drivers/atm/iphase.c:1178 rx_pkt() warn: curly braces intended?
The code is correct, the indention is misleading. In case the allocation
of skb fails, we want to skip to the end.
Signed-off-by: Tillmann Heidsieck <theidsieck@leenox.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch complains about returning hard coded error codes, silence this
warning.
drivers/atm/iphase.c:115 ia_enque_rtn_q() warn: returning -1 instead of -ENOMEM is sloppy
Signed-off-by: Tillmann Heidsieck <theidsieck@leenox.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes ip6_route_info_create return err pointer instead of
returning the rt pointer by reference as suggested by Dave
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
timewait or request sockets are small and do not contain sk->sk_tsflags
Without this fix, we might read garbage, and crash later in
__skb_complete_tx_timestamp()
-> sock_queue_err_skb()
(These pseudo sockets do not have an error queue either)
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman says:
====================
net: Pass net into defragmentation
This is the next installment of my work to pass struct net through the
output path so the code does not need to guess how to figure out which
network namespace it is in, and ultimately routes can have output
devices in another network namespace.
In netfilter and af_packet we defragment packets in the output path,
and there is the usual amount of confusion about how to compute which
net we are processing the packets in. This patchset clears that
confusion up by explicitly passing in struct net in ip_defrag,
ip_check_defrag, and nf_ct_frag6_gather.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The function nf_ct_frag6_gather is called on both the input and the
output paths of the networking stack. In particular ipv6_defrag which
calls nf_ct_frag6_gather is called from both the the PRE_ROUTING chain
on input and the LOCAL_OUT chain on output.
The addition of a net parameter makes it explicit which network
namespace the packets are being reassembled in, and removes the need
for nf_ct_frag6_gather to guess.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ip_defrag is called on both the input and the output
paths of the networking stack. In particular conntrack when it is
tracking outbound packets from the local machine calls ip_defrag.
So add a struct net parameter and stop making ip_defrag guess which
network namespace it needs to defragment packets in.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_call_ra_chain is called early in the forwarding chain from
ip_forward and ip_mr_input, which makes skb->dev the correct
expression to get the input network device and dev_net(skb->dev) a
correct expression for the network namespace the packet is being
processed in.
Compute the network namespace and store it in a variable to make the
code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent TCP listener patches exposed a prior af_packet bug :
match_fanout_group() blindly assumes it is always safe
to cast sk to a packet socket to compare fanout with af_packet_priv
But SYNACK packets can be sent while attached to request_sock, which
are smaller than a "struct sock".
We can read non existent memory and crash.
Fixes: c0de08d042 ("af_packet: don't emit packet on orig fanout group")
Fixes: ca6fb06518 ("tcp: attach SYNACK messages to request sockets instead of listener")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Eric Leblond <eric@regit.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
Major changes:
iwlwifi
* some debugfs improvements
* fix signedness in beacon statistics
* deinline some functions to reduce size when device tracing is enabled
* filter beacons out in AP mode when no stations are associated
* deprecate firmwares version -12
* fix a runtime PM vs. legacy suspend race
* one-liner fix for a ToF bug
* clean-ups in the rx code
* small debugging improvement
* fix WoWLAN with new firmware versions
* more clean-ups towards multiple RX queues;
* some rate scaling fixes and improvements;
* some time-of-flight fixes;
* other generic improvements and clean-ups;
brcmfmac
* rework code dealing with multiple interfaces
* allow logging firmware console using debug level
* support for BCM4350, BCM4365, and BCM4366 PCIE devices
* fixed for legacy P2P and P2P device handling
* correct set and get tx-power
ath9k
* add support for Outside Context of a BSS (OCB) mode
mwifiex
* add USB multichannel feature
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows configuring how the source address of ICMP
redirect messages is selected; by default the old behaviour is
retained, while setting icmp_redirects_use_orig_daddr force the
usage of the destination address of the packet that caused the
redirect.
The new behaviour fits closely the RFC 5798 section 8.1.1, and fix the
following scenario:
Two machines are set up with VRRP to act as routers out of a subnet,
they have IPs x.x.x.1/24 and x.x.x.2/24, with VRRP holding on to
x.x.x.254/24.
If a host in said subnet needs to get an ICMP redirect from the VRRP
router, i.e. to reach a destination behind a different gateway, the
source IP in the ICMP redirect is chosen as the primary IP on the
interface that the packet arrived at, i.e. x.x.x.1 or x.x.x.2.
The host will then ignore said redirect, due to RFC 1122 section 3.2.2.2,
and will continue to use the wrong next-op.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers need to implement both switchdev vlan ops and
vid_add/kill ndos. For that to work in bridge code, we need to try
switchdev op first when adding/deleting vlan id.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnx2_init_board, missing free temp_stats_blk on error path when
some operations do failed. Just add the 'kfree' operation.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
tcp: better smp listener behavior
As promised in last patch series, we implement a better SO_REUSEPORT
strategy, based on cpu hints if given by the application.
We also moved sk_refcnt out of the cache line containing the lookup
keys, as it was considerably slowing down smp operations because
of false sharing. This was simpler than converting listen sockets
to conventional RCU (to avoid sk_refcnt dirtying)
Could process 6.0 Mpps SYN instead of 4.2 Mpps on my test server.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Reducing tcp_timewait_sock from 280 bytes to 272 bytes
allows SLAB to pack 15 objects per page instead of 14 (on x86)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One 32bit hole is following skc_refcnt, use it.
skc_incoming_cpu can also be an union for request_sock rcv_wnd.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot
Sowmini Varadhan
Julia Lawall
Nikolay Aleksandrov
Tillmann Heidsieck
Roopa Prabhu
huangdaode
Eric Dumazet
David S. Miller
Eric W. Biederman
Paolo Abeni
Jiri Pirko
wangweidong