Before we start committing a transaction, we call
__journal_clean_checkpoint_list() to cleanup transaction's written-back
buffers.
If this call happens to remove all of them (and there were already some
buffers), __journal_remove_checkpoint() will decide to free the transaction
because it isn't (yet) a committing transaction and soon we fail some
assertion - the transaction really isn't ready to be freed :).
We change the check in __journal_remove_checkpoint() to free only a
transaction in T_FINISHED state. The locking there is subtle though (as
everywhere in JBD ;(). We use j_list_lock to protect the check and a
subsequent call to __journal_drop_transaction() and do the same in the end
of journal_commit_transaction() which is the only place where a transaction
can get to T_FINISHED state.
Probably I'm too paranoid here and such locking is not really necessary -
checkpoint lists are processed only from log_do_checkpoint() where a
transaction must be already committed to be processed or from
__journal_clean_checkpoint_list() where kjournald itself calls it and thus
transaction cannot change state either. Better be safe if something
changes in future...
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The AMD CS5535/CS5536 GPIO has two alternate output modes: AUX-1 and AUX-2.
When either AUX is enabled, the cs5535_gpio driver cannot control the
output.
Some BIOS code for the Geode processor enables AUX-1 for GPIO-1, which
configures it as the PC BEEP output.
This patch will disable AUX-1 and AUX-2 when the user enables output.
Signed-of-by: Ben Gardner <gardner.ben@gmail.com>
Cc: Richard Knutsson <ricknu-0@student.ltu.se>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
register_sysctl_table() can return NULL sometimes, e.g. when kmalloc()
returns NULL or when sysctl check fails.
I've also noticed, that many (most?) code in the kernel doesn't check for
the return value from register_sysctl_table() and later simply calls the
unregister_sysctl_table() with potentially NULL argument.
This is unlikely on a common kernel configuration, but in case we're
dealing with modules and/or fault-injection support, there's a slight
possibility of an OOPS.
Changing all the users to check for return code from the registering does
not look like a good solution - there are too many code doing this and
failure in sysctl tables registration is not a good reason to abort module
loading (in most of the cases).
So I think, that we can just have this check in unregister_sysctl_table
just to avoid accidental OOPS-es (actually, the unregister_sysctl_table()
did exactly this, before the start_unregistering() appeared).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- reconfigure SPI baud from speed_hz of each spi transfer
- according to spi_transfer.bits_per_word to reprogram register and setup
correct SPI operation handlers
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time
- move this static things to the blackfin board file
- add pin_req array to struct bfin5xx_spi_master
- tested on BF537/BF548 with SPI flash
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix SPI driver to work with SPI flash ST M25P16 on bf548
Currently the SPI driver enables the SPI controller and sets the SPI baud
register for each SPI transfer. But they should never be changed within a SPI
message session, in which several SPI transfers are pumped.
This patch moves SPI setting to the begining of a message session, and
never disables SPI controller until an error occurs.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Given the patch which simplifies the spi_sync calling convention, this one
updates the callers of that routine which tried using it according to the
previous specification. (Most didn't.)
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simplify spi_sync calling convention, eliminating the need to check both
the return value AND the message->status. In consequence, this corrects
misbehaviours of spi_read and spi_write (which only checked the former) and
their callers.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexey Dobriyan
Jan Kara
Nick Piggin
Ben Gardner
Pavel Emelyanov
Bryan Wu
Sonic Zhang
Mike Frysinger
Michael Hennerich
Marc Pignat