* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (36 commits)
USB: Driver for Freescale QUICC Engine USB Host Controller
USB: option: add QUANTA HSDPA Data Card device ids
USB: storage: Add another unusual_dev for off-by-one bug
USB: unusual_dev: usb-storage needs to ignore a device
USB: GADGET: fix !x & y
USB: new id for ti_usb_3410_5052 driver
USB: cdc-acm: Add another conexant modem to the quirks
USB: 'option' driver - onda device MT503HS has wrong id
USB: Remove ZTE modem from unusual_devices
USB: storage: support of Dane-Elec MediaTouch USB device
USB: usbmon: Implement compat_ioctl
USB: add kernel-doc for wusb_dev in struct usb_device
USB: ftdi_sio driver support of bar code scanner from Diebold
USB: ftdi_sio: added Alti-2 VID and Neptune 3 PID
USB: cp2101 device
USB: usblp.c: add USBLP_QUIRK_BIDIR to Brother HL-1440
USB: remove vernier labpro from ldusb
USB: CDC-ACM quirk for MTK GPS
USB: cdc-acm: support some gps data loggers
USB: composite: Fix bug: low byte of w_index is the usb interface number not the whole 2 bytes of w_index
...
This patch adds support for the FHCI USB controller, as found
in the Freescale MPC836x and MPC832x processors. It can support
Full or Low speed modes.
Quite a lot the hardware is doing by itself (SOF generation, CRC
generation and checking), though scheduling and retransmission is on
software's shoulders.
This controller does not integrate the root hub, so this driver also
fakes one-port hub. External hub is required to support more than
one device.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the support for the QUANTA Q101 series HSDPA Data Card.
With the vendor and product IDs are set properly,
the data card can be detected and works fine.
Signed-off-by: Alex Cheng <alex.cheng@quantatw.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Argosy has released another device with the off-by-one sector. This is a
harddrive with an internal cardreader which is affected.
Based on a patch written by Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Cc: Martijn Hijdra <martijn.hijdra@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds an unusual_devs entry for a Sony Ericsson modem. Like many
other modems, we have to ignore the storage device in order to access the
modem.
At this time usb_modeswitch does not work with this device.
Reported-by: The Solutor <thesolutor@gmail.com>.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Another Conexant, another device with the same quirk
Signed-off-by: Alan Cox <alan@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While trying to make GSM modem Onda MT503HS working, I found a mismatch
between device id in the driver code (0x0200) and id in the lsusb
output (0x2000).
This patch fixed it for me, but I don't know if the original device id was
also correct and the new ID should be added instead of replacing the
old one.
Signed-off-by: Marcel Sebek <sebek64@post.cz>
Acked-by: Domenico Riccio <domenico.riccio@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ZTE modem entry causes usb-storage to ignore the device, but for some
versions of the device, usb-storage mode is required to get to modem ode. For
both kinds the tool: http://www.draisberghof.de/usb_modeswitch/ should work.
Note that the various versions of the device have the same ProductId,
VendorId, and bcdDevice number, so we cannot have the entry for some and not
others.
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds another unusual_devs.h entry for a device that can't handle more
than 64k reads/writes in a single command.
Signed-off-by: Jean-Baptiste Onofre <jb@nanthrax.net>
Signed-off-by: Phil Dibowitz <phil@ipom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Running a 32-bit usbmon(8) on 2.6.28-rc9 produces the following:
ioctl32(usbmon:28563): Unknown cmd fd(3) cmd(400c9206){t:ffffff92;sz:12} arg(ffd3f458) on /dev/usbmon0
It happens because the compatibility mode was implemented for 2.6.18
and not updated for the fsops.compat_ioctl API.
This patch relocates the pieces from under #ifdef CONFIG_COMPAT into
compat_ioctl with no other changes except one new whitespace.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the product id of bcs(bar code scanner) from Diebold Procomp Brazil.
Signed-off-by: Mhayk Whandson <eu@mhayk.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My girl use modem GSM (EDGE) Commanader 2 on iPlus Polsih provider,
PLEASE add this vendor=0x10C4 and product=0x822B to USB serial driver cp2101.c
From: Tomasz K <eros81@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
My Brother HL-1440 would print one document before CUPS would stop
printing with the error "Printer not connected; will retry in 30
seconds...". I traced this down to the CUPS usb backend getting an EIO
out of usblp on the IOCNR_GET_DEVICE_ID IOCTL. Adding the
USBLP_QUIRK_BIDIR fixes the problem but is it the right solution?
output from strace /usr/lib/cups/backend/usb after printing a document
(Note: SNDCTL_DSP_SYNC == IOCNR_GET_DEVICE_ID):
before patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fff2478cef0) = -1 EIO (Input/output error)
after patch
open("/dev/usb/lp0", O_RDWR|O_EXCL) = 3
ioctl(3, SNDCTL_DSP_SYNC, 0x7fffb8d474c0) = 0
Possibly related bug: https://bugs.launchpad.net/ubuntu/+source/cupsys/+bug/35638
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Labpro device is in both ldusb and vstusb device tables.
Should only be a vstusb device.
Signed-off-by: stephen ware <stephen.ware@eqware.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a device quirk for a MediaTek Inc GPS chipset. The
device implements USB CDC ACM, but is missing the union descriptor, so
the ACM class driver fails to probe the device.
I've tested this patch with an iBlue A+ GPS which uses this chipset
and using kernel 2.6.28-rc9.
Signed-off-by: Andrew Lunn, <andrew@lunn.ch>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Below is a patch which allows a number of GPS loggers to work
under linux. It is known to support the i-Blue 747 (all models),
i-Blue 757, Qstarz BT-Q1000, i.Trek Z1, Konet BGL-32, and the Holux
M-241.
From: James A. Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some usb gadget driver, for example usb audio class device, the high
byte of w_index is the entity id and low byte is the interface number.
If we use the 2 bytes of w_index as the array number, we will get a
wrong pointer or NULL pointer.
This patch fixes this issue.
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Josh Boyer
Stephen Rothwell
Benjamin Herrenschmidt
Linus Torvalds
Anton Vorontsov
Alex.Cheng@quantatw.com
Phil Dibowitz
Roel Kluin
Oliver Neukum
Alan Cox
Marcel Sebek
Jean-Baptiste Onofre
Pete Zaitcev
Inaky Perez-Gonzalez
Mhayk Whandson
Robie Basak
Tomasz K
Brandon Philips
sware
Andrew Lunn
James A. Treacy
Bryan Wu