Phoenix Lite is based on the twl6030 family of PMICs. It has mostly the
same feature set of twl6030 but with small changes. The codec block has
also been removed. It also has a new charger block and new features in
its ADC block. VUSB handling also differs.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Maybe multiple PMIC devices are installed into one board. Static variable
can only make driver logic mess. So remove these variable, and use
platform data from platform driver instead.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In the current code, every time we set a TPS6586x GPIO pin,
the tps6586x_gpio_set function is resetting all other GPIO pins.
We need to update the right GPIOxOUT bit of the GPIOSET2 register instead
of overriding the full value.
Tested by setting sequentially GPIO2 and GPIO3 and verifying the
pins voltage.
Change-Id: I560edde146c5425cce37432c4ee91569eea5adcf
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the irq controller in Qualcomm 8xxx pmic. The 8xxx
interrupt controller provides control for gpio and mpp configured as
interrupts in addition to other subdevice interrupts. The interrupt
controller also provides a way to read the real time status of an
interrupt. This real time status is the only way one can get the
input values of gpio and mpp lines.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the Qualcomm PM8921 PMIC chip. The core driver
will communicate with the PMIC chip via the MSM SSBI bus.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
PCF50633_ADC and PCF50633_GPIO depends on MFD_PCF50633.
Thus group NXP PCF50633* drivers together.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Group TPSxxxxx power management chips together and sort in alphabetical order.
This change makes it easier for users to find config options.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Added API to get the TWL5030 Si version from the IDCODE register.
It is used for enabling the workaround for TWL erratum 27.
Signed-off-by: Lesly A M <leslyam@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Correcting the if condition check for printing the warning,
if wakeup script is not updated before updating the sleep script.
Since the flag 'order' is set to '1' while updating the wakeup script
for P1P2, the condition checking for printing the warning should be
if(!order) (ie: print the warning if wakeup script is not updated before
updating the sleep script)
Signed-off-by: Lesly A M <leslyam@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
WARNING: vmlinux.o(.devinit.text+0x6c4): Section mismatch in reference
from the function device_onkey_init() to the (unknown reference)
.init.data:(unknown)
The function __devinit device_onkey_init() references a (unknown reference)
__initdata (unknown).
If (unknown) is only used by device_onkey_init then annotate (unknown)
with a matching annotation.
It's caused by using __initdata on mfd cell resources. Replace __initdata
with __devinitdata.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The fact that we can't actually raise any interrupts doesn't stop us
setting up the IRQs we're exporting. While this isn't actually going
to do anything it allows us to proceed further through device setup
during board bringup and avoids issues with the MFD core not letting
us suppress the configuration of IRQ resources.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow the GPIO mode of WM831x devices to be configured using platform data.
Users may provide a table of GPIO register values in gpio_defaults[]. In
order to allow 0 to be set explicitly out of range values are accepted and
masked off, with a WM831X_GPIO_CONFIGURE define provided to set an out of
range value.
This can be used to configure higher numbered GPIOs or override values set
in OTP for GPIOs configured using OTP.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cell pointers are passed through device->mfd_cell and platform data
is passed through the MFD cell platform_data pointer.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Graeme Gregory
Haojian Zhuang
Vincent Palatin
Abhijeet Dharmapurikar
Axel Lin
Lesly A M
Wanlong Gao
Mark Brown
Samuel Ortiz