Currently the driver boots only via device tree hence add a
dependency on CONFIG_OF. This leaves with a bunch of unused code
so clean that up. This patch also makes use of probe_new function
in place of the probe function so as to avoid passing i2c_device_id.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Both Bay and Cherry Trail devices may be used together with a Crystal Cove
PMIC. Each platform has its own variant of the PMIC, which both use the
same ACPI HID, but they are not 100% compatible.
This commits makes the intel_soc_pmic_core code check the _HRV of the
ACPI-firmware-node and selects intel_soc_pmic_config_byt_crc resp.
intel_soc_pmic_config_cht_crc based on this.
This fixes the Bay Trail specific ACPI OpRegion code causing problems
on Cherry Trail devices. Specifically this was causing the external
microsd slot on a Dell Venue 8 5855 (Cherry Trail version) to not work
and the eMMC to become unreliable and throw lots of errors.
Fixes: 5165238460 ("mfd: intel_soc_pmic: Core driver")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The PMIC provides ACPI OpRegions which must be available for other
drivers' PS0 / PS3 methods early-on as such it must be builtin as the
Kconfig help text already states.
Somehow its Kconfig option ended up being a tristate though, this fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The TPS68470 device is an advanced power management
unit that powers a Compact Camera Module (CCM),
generates clocks for image sensors, drives a dual
LED for Flash and incorporates two LED drivers for
general purpose indicators.
This patch adds support for TPS68470 mfd device.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the MFD part of the ROHM BD9571MWV-M PMIC driver and MAINTAINERS
entry. The MFD part only specifies the regmap bits for the PMIC and
binds the subdevs together.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MTF_CORE should be enabled when driver is enabled.
Without this patch you can configure:
CONFIG_MFD_CORE is not set
CONFIG_MFD_TPS65086=y
... which ends up with compilation error:
drivers/mfd/tps65086.o: In function `tps65086_probe':
drivers/mfd/tps65086.c:110: undefined reference to `mfd_add_devices'
drivers/mfd/tps65086.c:110:(.text+0x128): relocation truncated to fit: \
R_AARCH64_CALL26 against undefined symbol `mfd_add_devices'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
STM32 Low-Power Timer hardware block can be used for:
- PWM generation
- IIO trigger (in sync with PWM)
- IIO quadrature encoder counter
PWM and IIO timer configuration are mixed in the same registers so
we need a multi fonction driver to be able to share those registers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The RK805 chip is a Power Management IC (PMIC) for multimedia and handheld
devices. It contains the following components:
- Regulators
- RTC
- Clocking
Both RK808 and RK805 chips are using a similar register map,
so we can reuse the RTC and Clocking functionality.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The LP87565 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Configurable Bucks(Single and multi-phase).
- Configurable General Purpose Output Signals (GPO).
The LP87565-Q1 variant device uses two 2-phase outputs configuration,
Buck0 is master for Buck0/1 output and Buck2 is master for Buck2/3
output.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On x86 the AXP288 PMIC provides an ACPI OpRegion handler, which must be
available before other drivers using it are loaded, which can only be
ensured if the MFD, OpRegion and i2c-bus drivers are built-in.
Since the AXP20x MFD code is used on non x86 too we cannot simply change
this into a bool, I've tried some Kconfig magic with if x86 but I could
not get this working correctly, so this commit just documents that this
should be built-in on x86, which fixes errors like these during boot:
mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
ACPI Error: No handler for Region [REGS] (ffff93543b0cc3a8) [UserDefinedRegion]
ACPI Error: Region UserDefinedRegion (ID=143) has no handler (20170119/exfldio-2
ACPI Error: Method parse/execution failed [\_SB.PCI0.I2C7.PMI5.GET] (Node ffff93
ACPI Error: Method parse/execution failed [\_SB.PCI0.SHC1._PS0] (Node ffff93543b
acpi 80860F14:02: Failed to change power state to D0
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add mfd driver for Intel CHT Whiskey Cove PMIC, based on various non
upstreamed CHT Whiskey Cove PMIC patches.
This is a somewhat minimal version which adds irqchip support and cells
for: ACPI PMIC opregion support, the i2c-controller driving the external
charger irc and the pwrsrc/extcon block.
Further cells can be added in the future if/when drivers are upstreamed
for them.
[The above patch caused a build error on some archetectures]
From: Arnd Bergmann <arnd@arndb.de>
I ran into a build error on ARM with a platform that has a non-standard
clk implementation:
drivers/clk/clk.o: In function `clk_disable':
clk.c:(.text.clk_disable+0x0): multiple definition of `clk_disable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_disable+0x0): first defined here
drivers/clk/clk.o: In function `clk_enable':
clk.c:(.text.clk_enable+0x0): multiple definition of `clk_enable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_enable+0x0): first defined here
The problem is a device driver that uses 'select COMMON_CLK', which is
generally a bad idea: selecting a subsystem should only be done from
a platform, otherwise we run into circular dependencies. The same driver
also selects 'GPIOLIB' and 'I2C', which has a similar effect.
This turns all three into 'depends on', as it should be.
Finally, we can limit the build to x86, unless we are compile testing.
First patch:
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix for first patch (squashed):
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Crystal Cove PMIC provides an ACPI OPRegion handler, which must be
available before other drivers using it are loaded, which is why
INTEL_SOC_PMIC is a bool.
Just having the driver is not enough, the driver for the i2c-bus must
also be built in, to ensure this, this patch adds a select for it.
This fixes errors like these during boot:
mmc0: SDHCI controller on ACPI [80860F14:00] using ADMA
ACPI Error: No handler for Region [REGS] (ffff93543b0cc3a8) [UserDefinedRegion] (20170119/evregion-166)
ACPI Error: Region UserDefinedRegion (ID=143) has no handler (20170119/exfldio-299)
ACPI Error: Method parse/execution failed [\_SB.PCI0.I2C7.PMI5.GET] (Node ffff93543b0cde10), AE_NOT_EXIST (20170119/psparse-543)
ACPI Error: Method parse/execution failed [\_SB.PCI0.SHC1._PS0] (Node ffff93543b0b5cd0), AE_NOT_EXIST (20170119/psparse-543)
acpi 80860F14:02: Failed to change power state to D0
While at it this patch also changes the human readable name of the Kconfig
option to make clear the INTEL_SOC_PMIC option selects support for the
Intel Crystal Cove PMIC and documents why this is a bool.
[The above patch caused a build error on some archetectures]
From: Arnd Bergmann <arnd@arndb.de>
I ran into a build error on ARM with a platform that has a non-standard
clk implementation:
drivers/clk/clk.o: In function `clk_disable':
clk.c:(.text.clk_disable+0x0): multiple definition of `clk_disable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_disable+0x0): first defined here
drivers/clk/clk.o: In function `clk_enable':
clk.c:(.text.clk_enable+0x0): multiple definition of `clk_enable'
arch/arm/mach-omap1/clock.o:clock.c:(.text.clk_enable+0x0): first defined here
The problem is a device driver that uses 'select COMMON_CLK', which is
generally a bad idea: selecting a subsystem should only be done from
a platform, otherwise we run into circular dependencies. The same driver
also selects 'GPIOLIB' and 'I2C', which has a similar effect.
This turns all three into 'depends on', as it should be.
Finally, we can limit the build to x86, unless we are compile testing.
First patch:
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix for first patch (squashed):
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Crystal Cove and Whiskey Cove are two different PMICs which are
installed on Intel Atom SoC based platforms.
Moreover there are two independent drivers that by some reason were
supposed (*) to get into one kernel module.
Fix the mess by clarifying Kconfig option for Crystal Cove and split
Whiskey Cove out of it.
(*) It looks like the configuration was never tested with
INTEL_SOC_PMIC=n. The line in Makefile is actually wrong.
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> (supporter:ACPI)
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MFD support for DA9061 is provided as part of the DA9062 device driver.
The registers header file adds two new chip variant IDs defined in DA9061
and DA9062 hardware. The core header file adds new software enumerations
for listing the valid DA9061 IRQs and a da9062_compatible_types enumeration
for distinguishing between DA9061/62 devices in software.
The core source code adds a new .compatible of_device_id entry. This is
extended from DA9062 to support both "dlg,da9061" and "dlg,da9062". The
.data entry now holds a reference to the enumerated device type.
A new regmap_irq_chip model is added for DA9061 and this supports the new
list of regmap_irq entries. A new mfd_cell da9061_devs[] array lists the
new sub system components for DA9061. Support is added for a new DA9061
regmap_config which lists the correct readable, writable and volatile
ranges for this chip.
The probe function uses the device tree compatible string to switch on the
da9062_compatible_types and configure the correct mfd cells, irq chip and
regmap config.
Kconfig is updated to reflect support for DA9061 and DA9062 PMICs.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These new helpers + macro definitions are meant to replace the old ones
which are unpractical to use.
Note that the macros and function prefixes have been intentionally
changed to ATMEL_[H]SMC_XX and atmel_[h]smc_ to reflect the fact that
this IP is also embedded in avr32 SoCs (and not only in at91 ones).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TI LMU (Lighting Management Unit) driver supports lighting devices below.
LM3532, LM3631, LM3632, LM3633, LM3695 and LM3697.
LMU devices have common features.
- I2C interface for accessing device registers
- Hardware enable pin control
- Backlight brightness control
- Notifier for hardware fault monitoring
- Regulators for LCD display bias
It contains fault monitor, backlight, LED and regulator driver.
LMU fault monitor
-----------------
LM3633 and LM3697 provide hardware monitoring feature.
It enables open or short circuit detection.
After monitoring is done, each device should be re-initialized.
Notifier is used for this case.
Separate patch for 'ti-lmu-fault-monitor' will be sent later.
Backlight
---------
It's handled by TI LMU backlight consolidated driver and
chip dependent data. Separate patchset will be sent later.
LED indicator
-------------
LM3633 has 6 indicator LEDs. Programmable dimming pattern is also
supported. Separate patch for 'leds-lm3633' will be sent later.
Regulator
---------
LM3631 has 5 regulators for the display bias.
LM3632 supports 3 regulators. One consolidated driver enables it.
The lm363x regulator driver is already upstreamed.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds the DMI system ID of the Kontron COMe-bBD#, COMe-bKL6,
COMe-cKL6, COMe-bSL6 and COMe-cAL6 boards to the Kontron PLD driver. The
list of supported products in the module description is also updated.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Christian Rauch <christian.rauch@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Many Motorola phones like droid 4 are using a custom PMIC called CPCAP
or 6556002. We can support it's core features quite easily with regmap_spi
and regmap_irq.
The children of cpcap, such as regulators, ADC and USB, can be just regular
device drivers and defined in the dts file. They get probed as we call
of_platform_populate() at the end of our probe, and then the children
can just call dev_get_regmap(dev.parent, NULL) to get the regmap.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Scott <michael.scott@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
MFD_SUN4I_GPADC and TOUCHSCREEN_SUN4I are incompatible (both are drivers
for Allwinner SoCs' ADC). This makes sure TOUCHSCREEN_SUN4I isn't
enabled while MFD_SUN4I_GPADC is enabled.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This hardware block could at used at same time for PWM generation
and IIO timers.
PWM and IIO timer configuration are mixed in the same registers
so we need a multi fonction driver to be able to share those registers.
version 7:
- rebase on v4.10-rc2
version 6:
- rename files to stm32-timers
- rename functions to stm32_timers_xxx
version 5:
- fix Lee comments about detect function
- add missing dependency on REGMAP_MMIO
version 4:
- add a function to detect Auto Reload Register (ARR) size
- rename the structure shared with other drivers
version 2:
- rename driver "stm32-gptimer" to be align with SoC documentation
- only keep one compatible
- use of_platform_populate() instead of devm_mfd_add_devices()
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:
+ DCDC4/DCDC5
+ LDO7-10
+ Slightly different output voltage/currents
+ 32kHz Output
+ RTC
+ USB Charger detection
Signed-off-by: Pierre-Hugues Husson <phh@phh.me>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The new sun4i mfd driver is lacking a dependency, triggering very rarely
int randconfig kernel builds:
drivers/mfd/sun4i-gpadc.o: In function `sun4i_gpadc_probe':
sun4i-gpadc.c:(.text.sun4i_gpadc_probe+0x110): undefined reference to `devm_regmap_add_irq_chip'
This adds a 'select REGMAP_IRQ', as the other drivers with this problem do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver only has runtime but no build time dependency with ARCH_U300 ||
ARCH_U8500 So it can be built for testing purposes if COMPILE_TEST option
is enabled.
This is useful to have more build coverage and make sure that the driver
is not affected by changes that could cause build regressions.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Keerthy
Hans de Goede
Rajmohan Mani
Marek Vasut
Michal Simek
Lee Jones
Fabrice Gasnier
Elaine Zhang
Andy Shevchenko
Steve Twiss
Boris Brezillon
Milo Kim
Ksenija Stanojevic
Michael Brunner
Tony Lindgren
Quentin Schulz
Benjamin Gaignard
Pierre-Hugues Husson
Arnd Bergmann
Javier Martinez Canillas