The user may want to use only some bits of the skb mark in
his skbedit rules because the remaining part might be used by
something else.
Introduce the "mask" parameter to the skbedit actor in order
to implement such functionality.
When the mask is specified, only those bits selected by the
latter are altered really changed by the actor, while the
rest is left untouched.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port_type_set() is been called and the new port type set is the same
as the old one, just return success.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
firewire-net, like the older eth1394 driver, reduced the initial MTU to
less than 1500 octets if the local link layer controller's asynchronous
packet reception limit was lower.
This is bogus, since this reception limit does not have anything to do
with the transmission limit. Neither did this reduction affect the TX
path positively, nor could it prevent link fragmentation at the RX path.
Many FireWire CardBus cards have a max_rec of 9, causing an initial MTU
of 1024 - 16 = 1008. RFC 2734 and RFC 3146 allow a minimum max_rec = 8,
which would result in an initial MTU of 512 - 16 = 496. On such cards,
IPv6 could only be employed if the MTU was manually increased to 1280 or
more, i.e. IPv6 would not work without intervention from userland.
We now always initialize the MTU to 1500, which is the default according
to RFC 2734 and RFC 3146.
On a VIA VT6316 based CardBus card which was affected by this, changing
the MTU from 1008 to 1500 also increases TX bandwidth by 6 %.
RX remains unaffected.
CC: netdev@vger.kernel.org
CC: linux1394-devel@lists.sourceforge.net
CC: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b3e3893e12 ("net: use core MTU range checking in misc drivers")
mistakenly introduced an upper limit for firewire-net's MTU based on the
local link layer controller's reception capability. Revert this. Neither
RFC 2734 nor our implementation impose any particular upper limit.
Actually, to be on the safe side and to make the code explicit, set
ETH_MAX_MTU = 65535 as upper limit now.
(I replaced sizeof(struct rfc2734_header) by the equivalent
RFC2374_FRAG_HDR_SIZE in order to avoid distracting long/int conversions.)
Fixes: b3e3893e1253('net: use core MTU range checking in misc drivers')
CC: netdev@vger.kernel.org
CC: linux1394-devel@lists.sourceforge.net
CC: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This node pointer is returned by of_get_child_by_name() with refcount
incremented in this function. of_node_put() on it before exitting this
function.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer() instead of init_timer(), being the preferred/standard
way to set a timer up.
Also, quoting the mod_timer() function comment:
-> mod_timer() is a more efficient way to update the expire field of an
active timer (if the timer is inactive it will be activated).
Use setup_timer and mod_timer to setup and arm a timer, to make the code
cleaner and easier to read.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENODEV from the DMA is not supported error
handling case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled, spin_lock_irqsave()
make sure always in irq disable context. So the kfree_skb()
should be replaced with dev_kfree_skb_irq().
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -EINVAL from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the function
and data fields.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not necessary to free memory allocated with devm_kzalloc in the
remove path and using kfree leads to a double free.
Fixes: 84640e27f2 ("net: netcp: Add Keystone NetCP core ethernet
driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum MTU is defined via the slave devices of an batman-adv
interface. Thus it is not possible to calculate the max_mtu during the
creation of the batman-adv device when no slave devices are attached. Doing
so would for example break non-fragmentation setups which then
(incorrectly) allow an MTU of 1500 even when underlying device cannot
transport 1500 bytes + batman-adv headers.
Checking the dynamically calculated max_mtu via the minimum of the slave
devices MTU during .ndo_change_mtu is also used by the bridge interface.
Cc: Jarod Wilson <jarod@redhat.com>
Fixes: b3e3893e12 ("net: use core MTU range checking in misc drivers")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xo Wang says:
====================
Broadcom BCM54612E support
This series is based on tip of torvalds/master.
The first patch adds register definitions from Broadcom docs.
The second patch adds the BCM54612E PHY ID, flags, and device-specific
RGMII internal delay initialization.
I tested on a custom board with an Aspeed AST2500 SOC with its second
MAC connected to this PHY.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This PHY has internal delays enabled after reset. This clears the
internal delay enables unless the interface specifically requests them.
Signed-off-by: Xo Wang <xow@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the RXD-to-RXC skew (delay) time bit in the Miscellaneous Control
shadow register and a mask for the shadow selector field.
Remove a re-definition of MII_BCM54XX_AUXCTL_SHDWSEL_AUXCTL.
Signed-off-by: Xo Wang <xow@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I prepared commit d250a5f90e ("pkt_sched: gen_estimator: Dont
report fake rate estimators"), htb still had an implicit rate estimator
for all its classes.
Then later, I made this rate estimator optional in commit 64153ce0a7
("net_sched: htb: do not setup default rate estimators"), but I forgot
to update htb use of gnet_stats_copy_rate_est()
After this patch, "tc -s qdisc ..." no longer report fake rate
estimators for HTB classes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In criu we are actively using diag interface to collect sockets
present in the system when dumping applications. And while for
unix, tcp, udp[lite], packet, netlink it works as expected,
the raw sockets do not have. Thus add it.
v2:
- add missing sock_put calls in raw_diag_dump_one (by eric.dumazet@)
- implement @destroy for diag requests (by dsa@)
v3:
- add export of raw_abort for IPv6 (by dsa@)
- pass net-admin flag into inet_sk_diag_fill due to
changes in net-next branch (by dsa@)
v4:
- use @pad in struct inet_diag_req_v2 for raw socket
protocol specification: raw module carries sockets
which may have custom protocol passed from socket()
syscall and sole @sdiag_protocol is not enough to
match underlied ones
- start reporting protocol specifed in socket() call
when sockets are raw ones for the same reason: user
space tools like ss may parse this attribute and use
it for socket matching
v5 (by eric.dumazet@):
- use sock_hold in raw_sock_get instead of atomic_inc,
we're holding (raw_v4_hashinfo|raw_v6_hashinfo)->lock
when looking up so counter won't be zero here.
v6:
- use sdiag_raw_protocol() helper which will access @pad
structure used for raw sockets protocol specification:
we can't simply rename this member without breaking uapi
v7:
- sine sdiag_raw_protocol() helper is not suitable for
uapi lets rather make an alias structure with proper
names. __check_inet_diag_req_raw helper will catch
if any of structure unintentionally changed.
CC: David S. Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Ahern <dsa@cumulusnetworks.com>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrey Vagin <avagin@openvz.org>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field is initialized by ILA and MPLS but never used. Remove it.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_mutex can be locked for a long time. It may be because many
namespaces are being destroyed or many processes decide to create
a network namespace.
Both these operations are heavy, so it is better to have an ability to
kill a process which is waiting net_mutex.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrei Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
META_COLLECTOR int_vlan_tag() assumes that if the accel tag (vlan_tci)
is zero, then no vlan accel tag is present.
This is incorrect for zero VID vlan accel packets, making the following
match fail:
tc filter add ... basic match 'meta(vlan mask 0xfff eq 0)' ...
Apparently 'int_vlan_tag' was implemented prior VLAN_TAG_PRESENT was
introduced in 05423b2 "vlan: allow null VLAN ID to be used"
(and at time introduced, the 'vlan_tx_tag_get' call in em_meta was not
adapted).
Fix, testing skb_vlan_tag_present instead of testing skb_vlan_tag_get's
value.
Fixes: 05423b2413 ("vlan: allow null VLAN ID to be used")
Fixes: 1a31f2042e ("netsched: Allow meta match on vlan tag on receive")
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: Driver update
Mostly cosmetics and small resource values management rewrite.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the number of resources is going to get much bigger, ease up the
addition by simly defining IDs. Convert the existing structure members
to a set array, one for validity, one for values. Introduce a set of
getters and setters for easy access.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the MLXSW_REG_DEFINE macro to store register name in string form.
Use this string later on instead of hard coded string values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Antonio Quartulli
Elad Raz
Stefan Richter
Wei Yongjun
Sven Eckelmann
David S. Miller
Xo Wang
Eric Dumazet
Cyrill Gorcunov
Thomas Graf
Andrey Vagin
Shmulik Ladkani
Jiri Pirko