We need to synchronize irqs before issuing reset to make sure that the
clients communication is concluded and doesn't leak to the reset flow
and confusing the state machine.
This issue is happening during suspend/resume stress testing.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vme_driver structure currently has a "shutdown" entry. This entry is
never used, it lacks the correct parameter (it should be providing a
pointer to the relevant vme_dev struct to even *look* usable), the VME
subsystem currently doesn't provide support for shutdown functions and no
in-tree drivers use it (hardly surprising, given it'd never be called).
Remove the entry from vme_driver to avoid confusion.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan writes:
fpga: Updates for 4.10
These are:
* Add git url to MAINTAINERS
* Allow write_init to specify how much buffer it needs
* Fixes for ISR state in zynq fpga manager driver
* Other small fixes for zynq
* Add Altera SoCFPGA drivers for COMPILE_TEST
The new driver caused a rare randconfig failure:
drivers/auxdisplay/ht16k33.o:(.data.ht16k33_fb_ops+0xc): undefined reference to `fb_sys_read'
drivers/auxdisplay/ht16k33.o:(.data.ht16k33_fb_ops+0x10): undefined reference to `fb_sys_write'
This selects the respective helper modules.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This interface was designed for streaming, but write_init's buf
argument has an unclear purpose. Define it to be the first bytes
of the bitstream. Each driver gets to set how many bytes (at most)
it wants to see. Short bitstreams will be passed through as-is, while
long ones will be truncated.
The intent is to allow drivers to peek at the header before the transfer
actually starts.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Alan Tull <atull@opensource.altera.com>
It is best practice to clear and mask all interrupts before
associating the IRQ, and this should be done after the clock
is enabled.
This corrects a bad result from zynq_fpga_ops_state on bootup
where left over latched values in INT_STS_OFFSET caused it to
report an unconfigured FPGA as configured.
After this change the boot up operating state for an unconfigured
FPGA reports 'unknown'.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Alan Tull <atull@opensource.altera.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
socfpga uses mgr->dev for debug prints, there should be consistency
here, so standardize on that. The only other use was for dma
which can be replaced with mgr->dev.parent.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Alan Tull <atull@opensource.altera.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Like Zynq the Altera drivers compile fine on x86 and others too,
so make it easier to compile test this stuff.
A10 requires REGMAP_MMIO to compile, so be explicit rather than
relying on it via ARCH_SOCFPGA.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Alan Tull <atull@opensource.altera.com>
pruss_probe() enables gdev->pruss_clk, but there is no clk_disable()
in the driver.
The patch adds clk_disable() to pruss_cleanup() and error handling for
clk_enable().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug is as old as git. We need to be calling spin_unlock_irqrestore()
instead of regular spin_unlock() here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After parport starts using the device model, all pardevice drivers
should decide in their match_port callback function if they want to
attach with that particulatr port. ppdev has been converted to use the
new parport device-model code but pp_attach() tried to attach with all
the ports.
Create a new array of pointer and use that to remember the ports we
have attached. And use that information to skip attaching ports which
we have already attached.
Tested-by: Joe Lawrence <joe.lawrence@redhat.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The variable name was only released if parport_register_dev_model()
fails. Now that we are using the device-model the parport driver
will duplicate the name and use it. So we can release the variable
after the device has been registered with the parport.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pm_runtime_autosuspend can take synchronous or asynchronous
paths, Because we are calling pm_runtime_mark_last_busy just before
this most of the cases it takes the asynchronous way. However,
when the FW or driver resets during already running runtime suspend,
the call will result in calling to the driver's rpm callback and results
in a deadlock on device_lock.
The simplest fix is to replace pm_runtime_autosuspend with
asynchronous pm_request_autosuspend.
Cc: <stable@vger.kernel.org> # 4.4+
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most error branches following the call to alloc_event_data contain a call
to etm_free_aux. This patch add a call to etm_free_aux to an error branch
that does not call it.
This issue was found with Hector.
Signed-off-by: Quentin Lambert <lambert.quentin@gmail.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tmc_etr_enable_hw() fills the buffer with 0's before enabling
the hardware. So, we don't need an explicit memset() in
tmc_enable_etr_sink_sysfs() before calling the tmc_etr_enable_hw().
This patch removes the explicit memset from tmc_enable_etr_sink_sysfs.
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode of operation of the TMC tracked in drvdata->mode is defined
as a local_t type. This is always checked and modified under the
drvdata->spinlock and hence we don't need local_t for it and the
unnecessary synchronisation instructions that comes with it. This
change makes the code a bit more cleaner.
Also fixes the order in which we update the drvdata->mode to
CS_MODE_DISABLED. i.e, in tmc_disable_etX_sink we change the
mode to CS_MODE_DISABLED before invoking tmc_disable_etX_hw()
which in turn depends on the mode to decide whether to dump the
trace to a buffer.
Applies on mathieu's coresight/next tree [1]
https://git.linaro.org/kernel/coresight.git next
Reported-by: Venkatesh Vivekanandan <venkatesh.vivekanandan@broadcom.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tomas Winkler
Martyn Welch
Greg Kroah-Hartman
Robin van der Gracht
Alan Tull
Jason Gunthorpe
Alexey Khoroshilov
Dan Carpenter
Moritz Fischer
Sudip Mukherjee
Alexander Usyskin
Quentin Lambert
Suzuki K Poulose