When sending "SLEEP" command to the controller it ceases scanning
completely and is unable to wake the system up from sleep, so if it is
configured as a wakeup source we should simply configure interrupt for
wakeup and rely on idle logic within the controller to reduce power
consumption while it is not used.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Atmel maxtouch DT binding documents that the compatible string for
the device is "atmel,maxtouch" and the I2C core always reports a module
alias of the form i2c:alias where alias is the compatible string model:
$ grep MODALIAS /sys/devices/platform/12e00000.i2c/i2c-8/8-004b/uevent
MODALIAS=i2c:maxtouch
But there isn't maxtouch entry in the I2C device ID table so when the
i2c:maxtouch MODALIAS uevent is reported, kmod is not able to match the
alias with a module to load:
$ modinfo atmel_mxt_ts | grep alias
alias: of:N*T*Catmel,maxtouch
alias: i2c:mXT224
alias: i2c:atmel_mxt_tp
alias: i2c:atmel_mxt_ts
alias: i2c:qt602240_ts
So add the maxtouch entry to the I2C device ID table to allow the module
to be autoloaded when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Apparently people are installing generic Linux distributions not only on
Pixels but also on other Chromebooks. Unfortunately on all of them Atmel
parts assigned names ATML0000 and ATML0001, and do not carry any other
configuration data. So let's create generic instance of platform data that
should cover most of them (we assume that they will not be using T100
objects, since with those Google mapped BTN_LEFT onto a different GPIO, so
slightly different keymap would be needed, but I think we used parts with
T100 on ARM devices where we thankfully have DTS and can describe the
devices better).
Tested-by: Rich K <rgkirch@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The functions, variables, and defines of the new tsc200x-core.c are
renamed to tsc200x instead of tsc2005 avoid possible confusion.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch separates the SPI functionality from core functionality
that overlaps with the tsc2004.
Prepares kernel for new tsc2004 driver without much redundant code.
Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix build errors due to missing Kconfig dependency.
drivers/built-in.o: In function `sur40_disconnect':
sur40.c:(.text+0x22be6e): undefined reference to `video_unregister_device'
sur40.c:(.text+0x22be77): undefined reference to `v4l2_device_unregister'
drivers/built-in.o: In function `sur40_process_video':
sur40.c:(.text+0x22c1d4): undefined reference to `v4l2_get_timestamp'
drivers/built-in.o: In function `sur40_probe':
sur40.c:(.text+0x22ca82): undefined reference to `v4l2_device_register'
sur40.c:(.text+0x22cb1a): undefined reference to `v4l2_device_unregister'
sur40.c:(.text+0x22cbf7): undefined reference to `video_device_release_empty'
sur40.c:(.text+0x22cc53): undefined reference to `__video_register_device'
sur40.c:(.text+0x22cc90): undefined reference to `video_unregister_device'
drivers/built-in.o: In function `sur40_vidioc_querycap':
sur40.c:(.text+0x22ccb0): undefined reference to `video_devdata'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If common clock framework is configured, the driver generates a warning,
which is fixed by this change:
root@devkit3250:~# cat /dev/input/touchscreen0
------------[ cut here ]------------
WARNING: CPU: 0 PID: 720 at drivers/clk/clk.c:727 clk_core_enable+0x2c/0xa4()
Modules linked in: sc16is7xx snd_soc_uda1380
CPU: 0 PID: 720 Comm: cat Not tainted 4.3.0-rc2+ #199
Hardware name: LPC32XX SoC (Flattened Device Tree)
Backtrace:
[<>] (dump_backtrace) from [<>] (show_stack+0x18/0x1c)
[<>] (show_stack) from [<>] (dump_stack+0x20/0x28)
[<>] (dump_stack) from [<>] (warn_slowpath_common+0x90/0xb8)
[<>] (warn_slowpath_common) from [<>] (warn_slowpath_null+0x24/0x2c)
[<>] (warn_slowpath_null) from [<>] (clk_core_enable+0x2c/0xa4)
[<>] (clk_core_enable) from [<>] (clk_enable+0x24/0x38)
[<>] (clk_enable) from [<>] (lpc32xx_setup_tsc+0x18/0xa0)
[<>] (lpc32xx_setup_tsc) from [<>] (lpc32xx_ts_open+0x14/0x1c)
[<>] (lpc32xx_ts_open) from [<>] (input_open_device+0x74/0xb0)
[<>] (input_open_device) from [<>] (evdev_open+0x110/0x16c)
[<>] (evdev_open) from [<>] (chrdev_open+0x1b4/0x1dc)
[<>] (chrdev_open) from [<>] (do_dentry_open+0x1dc/0x2f4)
[<>] (do_dentry_open) from [<>] (vfs_open+0x6c/0x70)
[<>] (vfs_open) from [<>] (path_openat+0xb4c/0xddc)
[<>] (path_openat) from [<>] (do_filp_open+0x40/0x8c)
[<>] (do_filp_open) from [<>] (do_sys_open+0x124/0x1c4)
[<>] (do_sys_open) from [<>] (SyS_open+0x2c/0x30)
[<>] (SyS_open) from [<>] (ret_fast_syscall+0x0/0x38)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the touchscreen controller ISR, reading the tsc starting from
register 0x2 causes the tsc to infrequently update the detected
finger's x and y coordinate. The irq pin toggles at a fast rate to
indicate touch events are happening. However, the tsc on average
updates the touch point's x and y value every ~100 ms which is much
slower than the advertised rate of 100+ Hz. This leads to multiple reads
within this ~100 ms time window returning the same value.
Example:
X: 10 , Y: 30
X: 10 , Y: 30
X: 10, Y: 30
..
// After 100 ms
X: 300, Y: 300
X: 300, y: 300
..
// After 100 ms
X: 1743, Y: 621
X: 1743, Y: 621
For some reason if instead of starting to read at register 0x2 you
start reading at register 0x0 this issue isn't seen. This seems like
a quirk only seen in the EDT FT5506 so to fix this issue simply
adjust the code to start reading from 0x0. Technically this isn't wrong
so no regressions should be seen with other touchscreen controllers
supported by this driver.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
FT5506 is essentially the same as other FT5x06 devices other than
supporting 10 support points.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Update the code so that the maximum supported points aren't hard coded but
can be changed.
Set the maximum support points based on the data passed along side the
compatible field.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Calculate the amount of data that needs to be read for the specified max
number of support points. If the maximum number of support points changes
then the amount that is read from the touch screen controller should
reflect this.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With commit 3fffd12839 ("i2c: allow specifying separate wakeup
interrupt in device tree") wakeirq is managed by i2c-core, so remove
wakeirq related code from pixcir_i2c_ts driver.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The copyright/license notice says that the code is licensed under GPL v2
only (not GPL v2+), so let's use proper string in MODULE_LICENSE().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the touch controller spec, SPI return a 16 bit value, only 12
bits are valid, they are bit[14-3].
The value of MISO and MOSI can be configured when SPI is in idle mode.
Currently this touch driver assumes the SPI bus sets the MOSI and MISO in
low level when SPI bus is in idle mode. So the bit[15] of the value got
from SPI bus is always 0. But when SPI bus congfigures the MOSI and MISO in
high level during the SPI idle mode, the bit[15] of the value get from SPI
is always 1. If bit[15] is not masked, we may get the wrong value.
Mask the invalid bit to make sure the correct value gets returned.
Regardless of the SPI bus idle configuration.
Signed-off-by: Andrey Gelman <andrey.gelman@compulab.co.il>
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no need to explicitly set .owner for the driver, the core will do
it for us.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since reset and wake pin are optional the gpio structure for those
pins may be null. Therefore, they can't be blindly passed to
desc_to_gpio.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fixes from Dmitry Torokhov:
"Fixes for two recent regressions (in Synaptics PS/2 and uinput
drivers) and some more driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - fix handling of disabling gesture mode"
Input: psmouse - fix data race in __ps2_command
Input: elan_i2c - add all valid ic type for i2c/smbus
Input: zhenhua - ensure we have BITREVERSE
Input: omap4-keypad - fix memory leak
Input: serio - fix blocking of parport
Input: uinput - fix crash when using ABS events
Input: elan_i2c - expand maximum product_id form 0xFF to 0xFFFF
Input: elan_i2c - add ic type 0x03
Input: elan_i2c - don't require known iap version
Input: imx6ul_tsc - fix controller name
Input: imx6ul_tsc - use the preferred method for kzalloc()
Input: imx6ul_tsc - check for negative return value
Input: imx6ul_tsc - propagate the errors
Input: walkera0701 - fix abs() calculations on 64 bit values
Input: mms114 - remove unneded semicolons
Input: pm8941-pwrkey - remove unneded semicolon
Input: fix typo in MT documentation
Input: cyapa - fix address of Gen3 devices in device tree documentation
This adds support for the FT6x06 and the FT6x36 family of capacitive touch
panel controllers, in particular the FT6236.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The PTR_ERR_OR_ZERO() helper function checks if a pointer contains an
errno code and returns it or return 0 if that's not the case. Use the
helper instead of open coding the same logic in the driver. This was
found with make coccicheck that complains with the following warning:
drivers/input/touchscreen/cyttsp4_i2c.c:53:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The PTR_ERR_OR_ZERO() helper function checks if a pointer contains an
errno code and returns it or return 0 if that's not the case. Use the
helper instead of open coding the same logic in the driver. This was
found with make coccicheck that complains with the following warning:
drivers/input/touchscreen/ads7846.c:532:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
James Chen
Javier Martinez Canillas
Dmitry Torokhov
Michael Welling
Randy Dunlap
Vladimir Zapolskiy
Franklin S Cooper Jr
Vignesh R
Andrey Gelman
Fengguang Wu
Yoichi Yuasa
Linus Torvalds
Noralf Trønnes