Input: tsc2005 - separate SPI and core functions

This patch separates the SPI functionality from core functionality
that overlaps with the tsc2004.

Prepares kernel for new tsc2004 driver without much redundant code.

Signed-off-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

drivers/input/touchscreen/Kconfig

@@ -939,10 +939,14 @@ config TOUCHSCREEN_TSC_SERIO
 	  To compile this driver as a module, choose M here: the
 	  module will be called tsc40.
 
+config TOUCHSCREEN_TSC200X_CORE
+	tristate
+
 config TOUCHSCREEN_TSC2005
 	tristate "TSC2005 based touchscreens"
 	depends on SPI_MASTER
 	select REGMAP_SPI
+	select TOUCHSCREEN_TSC200X_CORE
 	help
 	  Say Y here if you have a TSC2005 based touchscreen.
 

drivers/input/touchscreen/Makefile

@@ -69,6 +69,7 @@ obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213)	+= touchit213.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN)	+= touchwin.o
 obj-$(CONFIG_TOUCHSCREEN_TSC_SERIO)	+= tsc40.o
+obj-$(CONFIG_TOUCHSCREEN_TSC200X_CORE)	+= tsc200x-core.o
 obj-$(CONFIG_TOUCHSCREEN_TSC2005)	+= tsc2005.o
 obj-$(CONFIG_TOUCHSCREEN_TSC2007)	+= tsc2007.o
 obj-$(CONFIG_TOUCHSCREEN_UCB1400)	+= ucb1400_ts.o

drivers/input/touchscreen/tsc200x-core.h

@@ -0,0 +1,78 @@
+#ifndef _TSC200X_CORE_H
+#define _TSC200X_CORE_H
+
+/* control byte 1 */
+#define TSC2005_CMD			0x80
+#define TSC2005_CMD_NORMAL		0x00
+#define TSC2005_CMD_STOP		0x01
+#define TSC2005_CMD_12BIT		0x04
+
+/* control byte 0 */
+#define TSC2005_REG_READ		0x01 /* R/W access */
+#define TSC2005_REG_PND0		0x02 /* Power Not Down Control */
+#define TSC2005_REG_X			(0x0 << 3)
+#define TSC2005_REG_Y			(0x1 << 3)
+#define TSC2005_REG_Z1			(0x2 << 3)
+#define TSC2005_REG_Z2			(0x3 << 3)
+#define TSC2005_REG_AUX			(0x4 << 3)
+#define TSC2005_REG_TEMP1		(0x5 << 3)
+#define TSC2005_REG_TEMP2		(0x6 << 3)
+#define TSC2005_REG_STATUS		(0x7 << 3)
+#define TSC2005_REG_AUX_HIGH		(0x8 << 3)
+#define TSC2005_REG_AUX_LOW		(0x9 << 3)
+#define TSC2005_REG_TEMP_HIGH		(0xA << 3)
+#define TSC2005_REG_TEMP_LOW		(0xB << 3)
+#define TSC2005_REG_CFR0		(0xC << 3)
+#define TSC2005_REG_CFR1		(0xD << 3)
+#define TSC2005_REG_CFR2		(0xE << 3)
+#define TSC2005_REG_CONV_FUNC		(0xF << 3)
+
+/* configuration register 0 */
+#define TSC2005_CFR0_PRECHARGE_276US	0x0040
+#define TSC2005_CFR0_STABTIME_1MS	0x0300
+#define TSC2005_CFR0_CLOCK_1MHZ		0x1000
+#define TSC2005_CFR0_RESOLUTION12	0x2000
+#define TSC2005_CFR0_PENMODE		0x8000
+#define TSC2005_CFR0_INITVALUE		(TSC2005_CFR0_STABTIME_1MS    | \
+					 TSC2005_CFR0_CLOCK_1MHZ      | \
+					 TSC2005_CFR0_RESOLUTION12    | \
+					 TSC2005_CFR0_PRECHARGE_276US | \
+					 TSC2005_CFR0_PENMODE)
+
+/* bits common to both read and write of configuration register 0 */
+#define	TSC2005_CFR0_RW_MASK		0x3fff
+
+/* configuration register 1 */
+#define TSC2005_CFR1_BATCHDELAY_4MS	0x0003
+#define TSC2005_CFR1_INITVALUE		TSC2005_CFR1_BATCHDELAY_4MS
+
+/* configuration register 2 */
+#define TSC2005_CFR2_MAVE_Z		0x0004
+#define TSC2005_CFR2_MAVE_Y		0x0008
+#define TSC2005_CFR2_MAVE_X		0x0010
+#define TSC2005_CFR2_AVG_7		0x0800
+#define TSC2005_CFR2_MEDIUM_15		0x3000
+#define TSC2005_CFR2_INITVALUE		(TSC2005_CFR2_MAVE_X	| \
+					 TSC2005_CFR2_MAVE_Y	| \
+					 TSC2005_CFR2_MAVE_Z	| \
+					 TSC2005_CFR2_MEDIUM_15	| \
+					 TSC2005_CFR2_AVG_7)
+
+#define MAX_12BIT			0xfff
+#define TSC2005_DEF_X_FUZZ		4
+#define TSC2005_DEF_Y_FUZZ		8
+#define TSC2005_DEF_P_FUZZ		2
+#define TSC2005_DEF_RESISTOR		280
+
+#define TSC2005_SPI_MAX_SPEED_HZ       10000000
+#define TSC2005_PENUP_TIME_MS		40
+
+extern const struct regmap_config tsc200x_regmap_config;
+extern const struct dev_pm_ops tsc200x_pm_ops;
+
+int tsc200x_probe(struct device *dev, int irq, __u16 bustype,
+		  struct regmap *regmap,
+		  int (*tsc200x_cmd)(struct device *dev, u8 cmd));
+int tsc200x_remove(struct device *dev);
+
+#endif