Bharat Kumar Gogada reported issues with the generic MSI code, where the
end-point ended up with garbage in its MSI configuration (both for the vector
and the message).
It turns out that the two MSI paths in the kernel are doing slightly different
things:
generic MSI: disable MSI -> allocate MSI -> enable MSI -> setup EP
PCI MSI: disable MSI -> allocate MSI -> setup EP -> enable MSI
And it turns out that end-points are allowed to latch the content of the MSI
configuration registers as soon as MSIs are enabled. In Bharat's case, the
end-point ends up using whatever was there already, which is not what you
want.
In order to make things converge, we introduce a new MSI domain flag
(MSI_FLAG_ACTIVATE_EARLY) that is unconditionally set for PCI/MSI. When set,
this flag forces the programming of the end-point as soon as the MSIs are
allocated.
A consequence of this is that we have an extra activate in irq_startup, but
that should be without much consequence.
tglx:
- Several people reported a VMWare regression with PCI/MSI-X passthrough. It
turns out that the patch also cures that issue.
- We need to have a look at the MSI disable interrupt path, where we write
the msg to all zeros without disabling MSI in the PCI device. Is that
correct?
Fixes: 52f518a3a7 "x86/MSI: Use hierarchical irqdomains to manage MSI interrupts"
Reported-and-tested-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Reported-and-tested-by: Foster Snowhill <forst@forstwoof.ru>
Reported-by: Matthias Prager <linux@matthiasprager.de>
Reported-by: Jason Taylor <jason.taylor@simplivity.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1468426713-31431-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If a PCI bridge (or PCIe port) that is runtime-suspended gets an ACPI
hotplug notification, such as a bus check, it has to be resumed before
re-scanning the devices below it, or those devices will not be
accessible and will be treated as hot-removed.
Make that happen and let the bridge suspend again after the bus below it
has been re-scanned.
This is a replacement for commit 16468c783c ("ACPI / hotplug / PCI:
Runtime resume bridge before rescan") that has been reverted, because it
introduced a system resume regression (due to missing bridge->pci_dev
checks that are necessary in case the notification is targeted at the
host bridge) and it is necessary for the code added by commit
006d44e49a ("PCI: Add runtime PM support for PCIe ports") to work as
expected.
Tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge even more updates from Andrew Morton:
- dma-mapping API cleanup
- a few cleanups and misc things
- use jump labels in dynamic-debug
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
dynamic_debug: add jump label support
jump_label: remove bug.h, atomic.h dependencies for HAVE_JUMP_LABEL
arm: jump label may reference text in __exit
tile: support static_key usage in non-module __exit sections
sparc: support static_key usage in non-module __exit sections
powerpc: add explicit #include <asm/asm-compat.h> for jump label
drivers/media/dvb-frontends/cxd2841er.c: avoid misleading gcc warning
MAINTAINERS: update email and list of Samsung HW driver maintainers
block: remove BLK_DEV_DAX config option
samples/kretprobe: fix the wrong type
samples/kretprobe: convert the printk to pr_info/pr_err
samples/jprobe: convert the printk to pr_info/pr_err
samples/kprobe: convert the printk to pr_info/pr_err
dma-mapping: use unsigned long for dma_attrs
media: mtk-vcodec: remove unused dma_attrs
include/linux/bitmap.h: cleanup
tree-wide: replace config_enabled() with IS_ENABLED()
drivers/fpga/Kconfig: fix build failure
This reverts commit 16468c783c.
Bisection showed that it was the root cause for a resume hang on a
bog-standard all-Intel laptop (Sony Vaio Pro 11), and reverting fixes
the hang.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge yet more updates from Andrew Morton:
- the rest of ocfs2
- various hotfixes, mainly MM
- quite a bit of misc stuff - drivers, fork, exec, signals, etc.
- printk updates
- firmware
- checkpatch
- nilfs2
- more kexec stuff than usual
- rapidio updates
- w1 things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
ipc: delete "nr_ipc_ns"
kcov: allow more fine-grained coverage instrumentation
init/Kconfig: add clarification for out-of-tree modules
config: add android config fragments
init/Kconfig: ban CONFIG_LOCALVERSION_AUTO with allmodconfig
relay: add global mode support for buffer-only channels
init: allow blacklisting of module_init functions
w1:omap_hdq: fix regression
w1: add helper macro module_w1_family
w1: remove need for ida and use PLATFORM_DEVID_AUTO
rapidio/switches: add driver for IDT gen3 switches
powerpc/fsl_rio: apply changes for RIO spec rev 3
rapidio: modify for rev.3 specification changes
rapidio: change inbound window size type to u64
rapidio/idt_gen2: fix locking warning
rapidio: fix error handling in mbox request/release functions
rapidio/tsi721_dma: advance queue processing from transfer submit call
rapidio/tsi721: add messaging mbox selector parameter
rapidio/tsi721: add PCIe MRRS override parameter
rapidio/tsi721_dma: add channel mask and queue size parameters
...
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* pci/host-aardvark:
arm64: dts: marvell: Add Aardvark PCIe support for Armada 3700
PCI: aardvark: Add Aardvark PCI host controller driver
dt-bindings: add DT binding for the Aardvark PCIe controller
* pci/host-altera:
PCI: altera: Poll for link up status after retraining the link
PCI: altera: Check link status before retrain link
PCI: altera: Reorder read/write functions
* pci/host-dra7xx:
PCI: dra7xx: Fix return value in case of error
* pci/host-hv:
PCI: hv: Fix interrupt cleanup path
PCI: hv: Handle all pending messages in hv_pci_onchannelcallback()
PCI: hv: Don't leak buffer in hv_pci_onchannelcallback()
* pci/host-vmd:
x86/PCI: VMD: Separate MSI and MSI-X vector sharing
x86/PCI: VMD: Use x86_vector_domain as parent domain
x86/PCI: VMD: Use lock save/restore in interrupt enable path
x86/PCI: VMD: Initialize list item in IRQ disable
x86/PCI: VMD: Select device dma ops to override
* pci/host-xilinx:
PCI: xilinx: Fix return value in case of error
Manually apply changes from pci/demodularize-hosts and
pci/host-request-windows to drivers/pci/host/pci-aardvark.c
* pci/host-tegra:
PCI: tegra: Program PADS_REFCLK_CFG* registers with per-SoC values
PCI: tegra: Program PADS_REFCLK_CFG* always, not just on legacy SoCs
PCI: tegra: Stop setting pcibios_min_mem
PCI: tegra: Use generic pci_remap_iospace() rather than ARM32-specific one
PCI: tegra: Use lower-case hex consistently for register definitions
Conflicts:
drivers/pci/host/pci-tegra.c
Drop stray pci_ioremap_io() per Thierry Reding <treding@nvidia.com>;
removal tested by Jon Hunter <jonathanh@nvidia.com>.
* pci/resource:
unicore32/PCI: Remove pci=firmware command line parameter handling
ARM/PCI: Remove arch-specific pcibios_enable_device()
ARM64/PCI: Remove arch-specific pcibios_enable_device()
MIPS/PCI: Claim bus resources on PCI_PROBE_ONLY set-ups
ARM/PCI: Claim bus resources on PCI_PROBE_ONLY set-ups
PCI: generic: Claim bus resources on PCI_PROBE_ONLY set-ups
PCI: Add generic pci_bus_claim_resources()
alx: Use pci_(request|release)_mem_regions
ethernet/intel: Use pci_(request|release)_mem_regions
GenWQE: Use pci_(request|release)_mem_regions
lpfc: Use pci_(request|release)_mem_regions
NVMe: Use pci_(request|release)_mem_regions
PCI: Add helpers to request/release memory and I/O regions
PCI: Extending pci=resource_alignment to specify device/vendor IDs
sparc/PCI: Implement pci_resource_to_user() with pcibios_resource_to_bus()
powerpc/pci: Implement pci_resource_to_user() with pcibios_resource_to_bus()
microblaze/PCI: Implement pci_resource_to_user() with pcibios_resource_to_bus()
PCI: Unify pci_resource_to_user() declarations
microblaze/PCI: Remove useless __pci_mmap_set_pgprot()
powerpc/pci: Remove __pci_mmap_set_pgprot()
PCI: Ignore write combining when mapping I/O port space
* pci/aspm:
PCI/ASPM: Remove redundant check of pcie_set_clkpm
* pci/dpc:
PCI: Remove DPC tristate module option
PCI: Bind DPC to Root Ports as well as Downstream Ports
PCI: Fix whitespace in struct dpc_dev
PCI: Convert Downstream Port Containment driver to use devm_* functions
* pci/hotplug:
PCI: Allow additional bus numbers for hotplug bridges
* pci/misc:
PCI: Include <asm/dma.h> for isa_dma_bridge_buggy
PCI: Make bus_attr_resource_alignment static
MAINTAINERS: Add file patterns for PCI device tree bindings
PCI: Fix comment typo
* pci/msi:
PCI/MSI: irqchip: Fix PCI_MSI dependencies
* pci/pm:
PCI: pciehp: Ignore interrupts during D3cold
PCI: Document connection between pci_power_t and hardware PM capability
PCI: Add runtime PM support for PCIe ports
ACPI / hotplug / PCI: Runtime resume bridge before rescan
PCI: Power on bridges before scanning new devices
PCI: Put PCIe ports into D3 during suspend
PCI: Don't clear d3cold_allowed for PCIe ports
PCI / PM: Enforce type casting for pci_power_t
* pci/virtualization:
PCI: Add ACS quirk for Solarflare SFC9220
PCI: Add DMA alias quirk for Adaptec 3805
PCI: Mark Atheros AR9485 and QCA9882 to avoid bus reset
PCI: Add function 1 DMA alias quirk for Marvell 88SE9182
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_XGENE
drivers/pci/host/Kconfig: bool "X-Gene PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tanmay Inamdar <tinamdar@apm.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_HOST_THUNDER_PEM
drivers/pci/host/Kconfig: bool "Cavium Thunder PCIe controller to off-chip devices"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: David Daney <david.daney@cavium.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_HOST_THUNDER_ECAM
drivers/pci/host/Kconfig: bool "Cavium Thunder ECAM controller to on-chip devices on pass-1.x silicon"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: David Daney <david.daney@cavium.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_TEGRA
drivers/pci/host/Kconfig: bool "NVIDIA Tegra PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Stephen Warren <swarren@wwwdotorg.org>
CC: Alexandre Courbot <gnurou@gmail.com>
CC: linux-tegra@vger.kernel.org
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_RCAR_GEN2
drivers/pci/host/Kconfig: bool "Renesas R-Car Gen2 Internal PCI controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
CC: Valentine Barshak <valentine.barshak@cogentembedded.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_RCAR_GEN2_PCIE
drivers/pci/host/Kconfig: bool "Renesas R-Car PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Phil Edworthy <phil.edworthy@renesas.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_MVEBU
drivers/pci/host/Kconfig: bool "Marvell EBU PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog, remove "Module" from author comment]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
CC: Jason Cooper <jason@lakedaemon.net>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_LAYERSCAPE
drivers/pci/host/Kconfig: bool "Freescale Layerscape PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Minghuan Lian <minghuan.Lian@freescale.com>
CC: Mingkai Hu <mingkai.hu@freescale.com>
CC: Roy Zang <tie-fei.zang@freescale.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_KEYSTONE
drivers/pci/host/Kconfig: bool "TI Keystone PCIe controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-By: Murali Karicheri <m-karicheri2@ti.com>
This code is not being built as a module by anyone:
host/Kconfig:config PCI_HISI
host/Kconfig: bool "HiSilicon Hip05 and Hip06 SoCs PCIe controllers"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Zhou Wang <wangzhou1@hisilicon.com>
CC: Dacai Zhu <zhudacai@hisilicon.com>
CC: Gabriele Paoloni <gabriele.paoloni@huawei.com>
This code is not being built as a module by anyone:
drivers/pci/host/Kconfig:config PCI_HOST_GENERIC
drivers/pci/host/Kconfig: bool "Generic PCI host controller"
Remove uses of MODULE_DESCRIPTION(), MODULE_AUTHOR(), MODULE_LICENSE(),
etc., so that when reading the driver there is no doubt it is builtin-only.
The information is preserved in comments at the top of the file.
Replace module_platform_driver() with builtin_platform_driver(), which uses
the same init level priority, so init ordering is unchanged.
Note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
[bhelgaas: changelog]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Marc Zyngier
Rafael J. Wysocki
Linus Torvalds
Masahiro Yamada
Fabian Frederick
Bjorn Helgaas
Paul Gortmaker