Add a max retry limit for PRLI retries. Max retry limit (5) is same as used
in rport PLOGI. Once the retries are exhausted, invoke rport offline so that
existing logic of rport re-discovery can kick-in. Also fixed a bug in rport.c
where one less retry was happening.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When a rport goes offline, its speed setting was not reset. Subsequently, if
the rport was not deleted due to it coming back online within rport del
timeout, previously discovered speed would continue to show up. The fix is to
reset the speed when processing rport offline transition.
In rport attributes, rport's with unknown speed were indicated as TRL
enforced. The right thing do to would be to use TRL default speed to
determine if TRL is enforced, when TRL is enabled.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Do not update the coalesce flag of the intr_attr struct in driver config area
on config response. This is to prevent the coalesce flag being reported as on
after an ioc disable/enable even if it was set to off before disable.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use standards defined 2 * RA_TOV as a timeout for ELS Request retries.
And standards defined 3 * RA_TOV as a timeout for FC-CT Request retries.
Also, added a check to send RPSC2 to a Brocade Fabric only.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Added time stamp for fcport stats reset
- Added new fileds to the statistics data structures.
- Typo removal and minor cleanup.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fixes the APIs to obtain ioc attributes
- fix API to obtain wwpn, wwnn, and mac.
- add API to get mfg wwpn, wwnn, and mac.
- fix API to obtain wwn of boot target.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Vport state machine does not cleanup associated lport in some states: while
waiting for fdisc response or fdisc failure state. The fixe is to cleanup lport
on vport delete in all states. In fdisc state, discard fdisc response and
delete lport and wait for lport deletecompletion. in error state, delete lport
and wait for delete completion.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch enables creating PBC vport.
During fcs init, fcs will read PBC vport using bfa iocfc API and invoke fcb
callback to add the pbc vport entries into a list. The pbc vport list will be
traversed in the subsequent pci probe process and vport will be created using
fc transport provided vport create function.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The patch includes the driver side changes to enable basic PBC (PreBoot
Configuration) feature.
- Data structure changes and new definitions for PBC.
- APIs to access PBC info.
- Remove unused code.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch enables support of new mezzanine cards for HP and IBM blade server.
- Add new pciids for HP and IBM mezzanine card.
- Add a new firmware image for HP mezzanine card, which is running in
FC only mode. Rename firmware image to reflect the difference. Change the
firmware download code accordingly for the above changes.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fixes surrounding PCIe enhanced error handling:
(1) We need to reject all request generated internaly inside the driver as well
as request arriving from the scsi mid layer when PCIe EEH is active. The fix is
to add a per adapter flag called pci_error_recovery which is checked thru out
the driver when request are generated.
(2) We don't need to call the pci_driver->remove directly from the PCIe
callbacks becuase its already called from the PCIe EEH code. In its place we are
shutting down the watchdog timer, and flushing back all pending IO.
(3) We need to save and restore the pci state across PCIe EEH handling.
Signed-off-by: Eric Moore <eric.moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
In compliance to RFC793, a TCP graceful termination will be used
instead of an abortive termination for the case where the remote
has initiated the close of the connection.
Additionally, a TCP abortive termination will be used to close the
connection when a logout response is not received in time after a
logout request has been initiated.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added variables to separate the fine tuned timeout values for
connection destroy and context destroy for both 1g and 10g devices.
v2: Extended the 5771X disconnect timeout from 10s to 20s as the firmware
has a retransmission timeout of 16s. This fixes one of the iscsi_endpoint
leak issues when the target is slow or non-responsive to our TCP FIN.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For cases where the iSCSI disconnection procedure times out due to
the iSCSI daemon being slow or unresponsive, the bnx2i_stop routine
will now perform hardware cleanup via bnx2i_hw_ep_disconnect on all
active endpoints so that subsequent operations will perform properly.
Also moved the mutex locks inside ep_connect and ep_disconnect so
that proper exclusivity can resolve simultaneous calls to the
ep_disconnect routine.
v2: Removed the unnecessary read lock in the bnx2i_stop
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch introduces a new bnx2i_hw_ep_disconnect routine which
contains all chip related disconnect and clean up procedure of
iSCSI offload connections. This separation is intended as a
preparation for the subsequent bnx2i_stop patch.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Benjamin Li <benli@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The value used to change the endian representation on the new adapters has
changed. This patch updates that value.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch allows the driver to recognize a new Obsidian-E based adapter that
uses a new subsystem ID.
This patch also fixes a few tab/space problems.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Stanse found that in mvs_abort_task, mvi_dev is dereferenced earlier
than tested for being NULL. Move the assignment below the test.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The below patch fixes a warning message generated by gcc 4.6.0
CC drivers/scsi/hosts.o
drivers/scsi/hosts.c: In function 'scsi_host_alloc':
drivers/scsi/hosts.c:328:6: warning: variable 'rval' set but not used
Fix this by removing the rval but placing a printk warning where it
would have been set.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the user accidentally changes LUN mappings or it occurs
due to a bug, then it can cause data corruption that can take
months and months to track down. This patch adds a log
message when getting REPORT_LUNS_DATA_CHANGED and it adds
a generic message for other Unit Attentions with asc == 0x3f.
We are working on adding support for handling of these errors,
but I think until then we should at least log a message so
tracking down problems as a result of one of these changes
is a little easier.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Jing Huang
Eric Moore
Eddie Wai
Michael Chan
FUJITA Tomonori
Wayne Boyer
Jiri Slaby
Kei Tokunaga
Justin P. Mattock
Mike Christie