- s/Device Drivers/Controllers/
- clarify who needs pcilynx
- don't recommend Y for raw1394; M is typically used
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Remove the unneeded code that clears, sets and again clears the
rcvPhyPkt bit in the ohci1394 LinkControl register in ohci_initialize().
Signed-off-by: Bernhard Kauer <kauer@os.inf.tu-dresden.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If posted write failed, an "Unhandled interrupt(s) 0x00000100" message
was logged by mistake.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
eth1394 did not work on buses consisting of S100B...S400B hardware
because it attempted to send GASP packets at S800.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch fixes some error handlings in eth1394:
- check return value of kmem_cache_create()
- cleanup resources if hpsb_register_protocol() fails
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (whitespace)
This patch actually doesn't change anything because there was always 0
== NETDEV_TX_OK returned before.
TODO: Return NETDEV_TX_BUSY in error case and test in different error
conditions.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
RFC 2734 says: "IP-capable nodes may operate with an MTU size larger
than the default [1500 octets], but the means by which a larger MTU is
configured are beyond the scope of this document."
Allow users to set an MTU bigger than 1500.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Call only eth1394's own host reset handler from .tx_timeout, not the
reset hooks of all other IEEE 1394 drivers.
A minor drawback of this patch is that ether1394_host_reset by timeout
is not serialized against ether1394_host_reset by bus reset.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Move common code into an extra function. This implicitly adds a missing
node_info->fifo = CSR1212_INVALID_ADDR_SPACE; to .update.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Adjust white space and line wraps. Remove unnecessary parentheses and
braces, unused macros, and some of the more redundant comments.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
There is some common code between ether1394_open and ether1394_add_host
which can be moved to a separate helper function for a slightly smaller
eth1394 driver (-160 bytes on i386.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Until now, ieee1394 put an IP-over-1394 capability entry into each new
host's config ROM. As soon as the controller was initialized --- i.e.
right after modprobe ohci1394 --- this entry triggered a hotplug event
which typically caused auto-loading of eth1394.
This irritated or annoyed many users and distributors. Of course they
could blacklist eth1394, but then ieee1394 wrongly advertized IP-over-
1394 capability to the FireWire bus.
Therefore
- remove the offending kernel config option
IEEE1394_CONFIG_ROM_IP1394,
- let eth1394 add the ROM entry by itself, i.e. only after eth1394 was
loaded.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=7793 .
To emulate the behaviour of older kernels, simply add the following to
to /etc/modprobe.conf:
install ohci1394 /sbin/modprobe eth1394; \
/sbin/modprobe --ignore-install ohci1394
Note, autoloading of eth1394 when an _external_ IP-over-1394 capable
device is discovered is _not_ affected by this patch.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Shrinks eth1394.ko by about 5%.
Many of these functions have only one caller and are therefore auto-
inlined anyway.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter
Simon Arlott
Bernhard Kauer
Akinobu Mita
Adrian Bunk
Jean Delvare