Driver has following initialization sequence for Target mode
1. Driver initialization starts
2. ISP Abort is scheduled when the target is enabled.
qla2xxx [0000:04:00.0]-4807:25: ISP abort scheduled
qla2xxx [0000:04:00.0]-00af:25: Performing ISP error recovery - ha=ffff880caa9e0000.
3. DPC thread starts the ISP Abort
4. While DPC is resetting the chip and initializing the firmware, we get
async events from the firmware about P2P mode, LOOP UP and PORT UPDATE.
5. PRLI from a initiator is delivered to us followed by a PLOGI and then a
SCSI command which creates a session.
6. If the SCSI command is a WRITE in this case, we issue XFR RDY and it
gets dropped as can be seen with messages RESET-XFR because ISP Abort
is still active
qla2xxx [0000:04:00.0]-e902:25: RESET-XFR active/old-count/new-count = 1/1/1.
7. If the SCSI command is a READ, we issue RESPONSE and they get dropped
as well because Abort is still active.
qla2xxx [0000:04:00.0]-e901:25: RESET-RSP active/old-count/new-count = 1/1/1
8. Now eventually, ISP Abort finishes clearing the DPC flags.
qla2xxx [0000:04:00.0]-8822:25: qla2x00_abort_isp succeeded.
qla2xxx [0000:04:00.0]-4808:25: ISP abort end.
9. Since we dropped SCSI commands silently (without any responses sent
to the initiator) initiator waits for a SCSI timeout (which is 60
seconds in our case), Sends an ABTS which fails since there
no se_cmd found for the tag that ABTS is referencing as the
commands were cleaned up in Step 6 and 7.
10. Initiator send an IO after the ABTS which succeed fine.
To fix the above case, the following changes have been made:
- To prevent target from dropping commands silently, use the online flag
instead to check for an active chip reset. Once the port is online during
a chip reset phase, we are good to process the commands.
- Clean up qla2x00_restart_isp to not set the online flag and process ATIO
as it is unnecessary. During a chip reset, interrupts are enabled only
after setting the online flag to 1, so ATIO's won't be missed and hence
no need to process ATIO's after setting the online flag.
Signed-off-by: Dilip Kumar Uppugandla <dilip@purestorage.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
99% of the time the ATIOQ has SCSI command. The other 1% of time
is something else. Most of the time this interrupt does not need
to hold the hardware_lock. We're moving the ATIO interrupt thread
to a different lock to reduce lock contention.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Sessions management (add, deleted, modify) currently are serialized
through the hardware_lock. Hardware_lock is a high traffic lock.
This lock is accessed by both the transmit & receive sides.
Sessions management is now moved off to another lock call sess_lock.
This is done to reduce lock contention and increase traffic throughput.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Replace QLA_TGT_STATE_ABORTED state with a bit because
the current state of the command is lost when an abort
is requested by upper layer.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Until now ack'ing of a new PLOGI has only been delayed if there
was an existing session for the same WWN. Ack was released when
the session deletion completed.
If there was another WWN session with the same fc_id/loop_id pair
(aka "conflicting session"), PLOGI was still ack'ed immediately.
This potentially caused a problem when old session deletion logged
fc_id/loop_id out of FW after new session has been established.
Two work-arounds were attempted before:
1. Dropping PLOGIs until conflicting session goes away.
2. Detecting initiator being logged out of FW and issuing LOGO
to force re-login.
This patch introduces proper solution to the problem where PLOGI
is held until either existing session with same WWN or any
conflicting session goes away. Mechanism supports one session holding
two PLOGI acks as well as one PLOGI ack being held by many sessions.
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
1. Initiator A is logged in with fc_id(1)/loop_id(1)
2. Initiator A re-logs in with fc_id(2)/loop_id(2)
3. Part of old session deletion async logoout for 1/1 is queued
4. Initiator B logs in with fc_id(1)/loop_id(1), starts
passing data and creates session.
5. Async logo from 3 is processed by DPC and sent to FW
Now initiator B has the session but is logged out from FW.
This condition is detected first with CTIO error 29 at which
point we should delete current session. During session
deletion we will send LOGO to initiator to force re-login.
Under rare circumstances initiator might be logged out of FW,
not have driver session, but still think it's logged in.
E.g. the above sequence plus session deletion due to re-config.
Incoming commands will fail to create local session because
initiator is not found in FW. In this case we also issue LOGO
to initiator to force him re-login.
Finally this patch fixes exchange leak when commands where
received in logged out state. In this case loop_id must be
set to FFFF when corresponding exchange is terminated. The
patch modifies exchange termination to always use FFFF,
since in certain scenarios it's impossible to tell whether
command was received in logged in or logged out state.
Signed-off-by: Alexei Potashnik <alexei@purestorage.com>
Acked-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
DebugFS now will show fw_resource_count node.
FW Resource count
Original TGT exchg count[0]
current TGT exchg count[0]
original Initiator Exchange count[2048]
Current Initiator Exchange count[2048]
Original IOCB count[2078]
Current IOCB count[2067]
MAX VP count[254]
MAX FCF count[0]
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Following counters are added in target mode to help debugging efforts.
Target Counters
qla_core_sbt_cmd = 0
qla_core_ret_sta_ctio = 0
qla_core_ret_ctio = 0
core_qla_que_buf = 0
core_qla_snd_status = 0
core_qla_free_cmd = 0
num alloc iocb failed = 0
num term exchange sent = 0
num Q full sent = 0
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables Exchange offload support in Qlogic ISP.
To enable exchange offload with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexchoffld to any non-zero number.
This will alow ISP firmware to store exchange data structures
used by firmware to host memory provided by driver. ISP firmware
can supports upto 32k total active exchanges.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch enables Extended Logins support in Qlogic ISP.
To enable extended login with Qlogic ISP24XX/25XX/26XX,
set module parameter ql2xexlogins to any non-zero number.
This will alow ISP firmware to store port database structure
information of remote login sessions to host memory provided
by driver. ISP firmware supports upto 16k total logins.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The following message is displayed in dmesg when a deprecated attribute
is set:
"ignoring deprecated ##_name## attribute"
This patch fixes the format to include the name of the deprecated
attribute.
Signed-off-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This change sets the LBPRZ flag in EVPD page b2h and READ CAPACITY (16)
based on a new unmap_zeroes_data device attribute. This flag is set
automatically for iblock based on underlying block device queue's
discard_zeroes_data flag.
Signed-off-by: Jamie Pocas <jamie.pocas@emc.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Modify indentation such that the 'smatch' tool no longer complains
about incorrect indentation + unreachable code.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Allow using the tcm function as a component of a gadget composed with
ConfigFS.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Do not directly use file static strings definitions in instances of f_tcm.
Instead use usb_gstrings_attach.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Dilip Kumar Uppugandla
Quinn Tran
Alexei Potashnik
Himanshu Madhani
Geliang Tang
Christophe Vu-Brugier
Jamie Pocas
Bart Van Assche
Andrzej Pietrasiewicz