When adding vlans with multiple IFLA_BRIDGE_VLAN_INFO attrs set in AFSPEC,
we would wipe the vlan obj struct after the first IFLA_BRIDGE_VLAN_INFO.
Fix this by only clearing what's necessary on each IFLA_BRIDGE_VLAN_INFO
iteration.
Fixes: 9e8f4a54 ("switchdev: push object ID back to object structure")
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Samuel Ortiz says:
====================
NFC 4.4 pull request
This is the NFC pull request for 4.4.
It's a bit bigger than usual, the 3 main culprits being:
- A new driver for Intel's Fields Peak NCI chipset. In order to
support this chipset we had to export a few NCI routines and
extend the driver NCI ops to not only support proprietary
commands but also core ones.
- Support for vendor commands for both STM drivers, st-nci
and st21nfca. Those vendor commands allow to run factory tests
through the NFC netlink interface.
- New i2c and SPI support for the Marvell driver, together with
firmware download support for this driver's core.
Besides that we also have:
- A few file renames in the STM drivers, to keep the naming
consistent between drivers.
- Some improvements and fixes on the NCI HCI layer, mostly to
properly reach a secure element over a legacy HCI link.
- A few fixes for the s3fwrn5 and trf7970a drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-10-28
Here are a some more Bluetooth patches for 4.4 which collected up during
the past week. The most important ones are from Kuba Pawlak for fixing
locking issues with SCO sockets. There's also a fix from Alexander Aring
for 6lowpan, a memleak fix from Julia Lawall for the btmrvl driver and
some cleanup patches from Marcel.
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that we reinitialize the interface if the MTU is
increased back above IPV6_MIN_MTU and the interface is up.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko says:
====================
mlxsw: driver update
This driver update mainly brings support for user to be able to setup
flooding on specified port, via bridge flag. Also, there is a fix in ageing
time conversion. The rest is just cosmetics.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes those places where checkpatch complains that comparisons
should place the constant on the right side of the test.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value passed through switchdev attr set is not in jiffies, but in
clock_t, so fix the convert.
Reported-by: Sagi Rotem <sagir@mellanox.com>
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add or remove a bridged port from the flooding domain of unknown unicast
packets according to user configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling a range of VLANs on a bridged port we can configure
flooding for these VLANs by one register access instead of calling the
same register for each VLAN. This is accomplished by using the 'range'
field of the Switch Flooding Table Register (SFTR).
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a flag anyway, so move it to existing u8 flag and don't waste mem.
Fix the flags to be in single u8 on the way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain use cases it is not always desirable for the switch device to
flood traffic to CPU port. Instead, only certain packet types (e.g.
STP, LACP) should be trapped to it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow devices supporting this feature to control the flooding of unknown
unicast traffic, by making switchdev infrastructure propagate this setting
to the switch driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iyappan Subramanian says:
====================
drivers: xgene: Add support RGMII TX/RX delay configuration
X-Gene RGMII ethernet controller has a RGMII bridge that performs the
task of converting the RGMII signal {RX_CLK,RX_CTL, RX_DATA[3:0]} from
PHY to GMII signal {RX_DV,RX_ER,RX_DATA[7:0]} and vice versa. This
RGMII bridge has a provision to internally delay the input RX_CLK and
the output TX_CLK using configuration registers. This will help in
maintain the CLK-CTL delay relationship in various operating
conditions.
This patch adds support RGMII TX/RX delay configuration.
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add RGMII TX/RX delay configuration support. RGMII standard requires 2ns
delay to help the RGMII bridge receiver to sample data correctly. If the
default value does not provide proper centering of the data sample, the
TX/RX delay parameters can be used to adjust accordingly.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problem Description:
We can add fdbs pointing to the bridge with NULL ->dst but that has a
few race conditions because br_fdb_insert() is used which first creates
the fdb and then, after the fdb has been published/linked, sets
"is_local" to 1 and in that time frame if a packet arrives for that fdb
it may see it as non-local and either do a NULL ptr dereference in
br_forward() or attach the fdb to the port where it arrived, and later
br_fdb_insert() will make it local thus getting a wrong fdb entry.
Call chain br_handle_frame_finish() -> br_forward():
But in br_handle_frame_finish() in order to call br_forward() the dst
should not be local i.e. skb != NULL, whenever the dst is
found to be local skb is set to NULL so we can't forward it,
and here comes the problem since it's running only
with RCU when forwarding packets it can see the entry before "is_local"
is set to 1 and actually try to dereference NULL.
The main issue is that if someone sends a packet to the switch while
it's adding the entry which points to the bridge device, it may
dereference NULL ptr. This is needed now after we can add fdbs
pointing to the bridge. This poses a problem for
br_fdb_update() as well, while someone's adding a bridge fdb, but
before it has is_local == 1, it might get moved to a port if it comes
as a source mac and then it may get its "is_local" set to 1
This patch changes fdb_create to take is_local and is_static as
arguments to set these values in the fdb entry before it is added to the
hash. Also adds null check for port in br_forward.
Fixes: 3741873b4f ("bridge: allow adding of fdb entries pointing to the bridge device")
Reported-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other callers of udp_tunnel6_xmit_skb just pass 0 for the prio
argument. Jesse Gross <jesse@nicira.com> suggested that prio is really
the same as IPv4's tos and should be handled the same, so this is my
interpretation of that suggestion.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Jesse Gross <jesse@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NOTE: Link-local IPv6 addresses for remote endpoints are not supported,
since the driver currently has no capacity for binding a geneve
interface to a specific link.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a build error that seems to be toochain
dependent (Not seen with gcc v5.1):
In file included from net/nfc/nci/rsp.c:36:0:
net/nfc/nci/rsp.c: In function ‘nci_rsp_packet’:
include/net/nfc/nci_core.h:355:12: error: inlining failed in call to
always_inline ‘nci_prop_rsp_packet’: function body not available
inline int nci_prop_rsp_packet(struct nci_dev *ndev, __u16 opcode,
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Scott Feldman
David S. Miller
Alexander Duyck
Jiri Pirko
Or Gerlitz
Ido Schimmel
Iyappan Subramanian
Roopa Prabhu
John W. Linville
Robert Dolca