Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have
their MODEM-control signals tied off to a static state. However UARTs A
and B can optionally route those signals to/from package pins, depending
on the exact pinmux configuration.
When these signals are not routed to package pins, false interrupts may
trigger either temporarily, or permanently, all while not showing up in
the IIR; it will read as NO_INT. This will eventually lead to the UART
IRQ being disabled due to unhandled interrupts. When this happens, the
kernel may print e.g.:
irq 68: nobody cared (try booting with the "irqpoll" option)
In order to prevent this, enable UART_BUG_NOMSR. This prevents
UART_IER_MSI from being enabled, which prevents the false interrupts
from triggering.
In practice, this is not needed under any of the following conditions:
* On Tegra chips after Tegra30, since the HW bug has apparently been
fixed.
* On UARTs C..E since their MODEM control signals are tied to the correct
static state which doesn't trigger the issue.
* On UARTs A..B if the MODEM control signals are routed out to package
pins, since they will then carry valid signals.
However, we ignore these exceptions for now, since they are only relevant
if a board actually hooks up more than a 4-wire UART, and no currently
supported board does this. If we ever support a board that does, we can
refine the algorithm that enables UART_BUG_NOMSR to take those exceptions
into account, and/or read a flag from DT/... that indicates that the
board has hooked up and pinmux'd more than a 4-wire UART.
Reported-by: Olof Johansson <olof@lixom.net> # autotester
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using RX DMA, the driver won't pass any data to the uart layer
until the buffer is flipped. When the port is shutdown, the dma buffers
are unmapped, but the head and tail of the ring buffer are not reseted.
Since the serial console will keep the port open, this will only
present itself when the uart is not shared.
To reproduce the issue, with an unpatched driver, run a getty on /dev/ttyS0
with no serial console and exit. Getty will exit, and when the new one returns
you will be unable to log in. If you hold down a key long enough to fill the
DMA buffer and flip it, you can then log in.
Signed-off-by: Mark Deneen <mdeneen@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
[nicolas.ferre@atmel.com: adapt to mainline kernel, handle !DMA case]
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The _remove callback could be called when a tasklet is scheduled. tasklet_kill
was called inside the function in order to free up any scheduled tasklets.
However it was called after uart_remove_one_port which destroys tty references
needed in the port for atmel_tasklet_func.
Simply putting the tasklet_kill at the start of the function will prevent this
conflict.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupts were being cleaned up late in the shutdown handler, it is possible
that an interrupt can occur and schedule a tasklet that runs after the port is
cleaned up. There is a null dereference due to this race condition with the
following stacktrace:
[<c02092b0>] (atmel_tasklet_func+0x514/0x814) from [<c001fd34>] (tasklet_action+0x70/0xa8)
[<c001fd34>] (tasklet_action+0x70/0xa8) from [<c001f60c>] (__do_softirq+0x90/0x144)
[<c001f60c>] (__do_softirq+0x90/0x144) from [<c001fa18>] (irq_exit+0x40/0x4c)
[<c001fa18>] (irq_exit+0x40/0x4c) from [<c000e298>] (handle_IRQ+0x64/0x84)
[<c000e298>] (handle_IRQ+0x64/0x84) from [<c000d6c0>] (__irq_svc+0x40/0x50)
[<c000d6c0>] (__irq_svc+0x40/0x50) from [<c0208060>] (atmel_rx_dma_release+0x88/0xb8)
[<c0208060>] (atmel_rx_dma_release+0x88/0xb8) from [<c0209740>] (atmel_shutdown+0x104/0x160)
[<c0209740>] (atmel_shutdown+0x104/0x160) from [<c0205e8c>] (uart_port_shutdown+0x2c/0x38)
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Acked-by: Leilei Zhao <leilei.zhao@atmel.com>
Cc: <stable@vger.kernel.org> # v3.12
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rx dma-callback it calls tasklet_schedule, if the tasklet
be scheduled after all the dma-callback in the rx dma channel,
current check condition in the tasklet will not do fetch dma
buffer into tty because tx_issued is equal with tx_completed,
so as timeout tasklet does.
so we check whether we should fetch the whole dma buffer into
tty according to the status of transactions in rx dma channel.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
this patch provides PM entry of uart_ops, then drop clk enable and
disable because serial core will do it.
the patch also fixes the issue that uart hang in resume caused by
not-enabled clock.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
use SET_SYSTEM_SLEEP_PM_OPS to initialize suspend/resume functions
instead of legacy suspend and resume entries of platform_driver.
this will add hibernation support automatically as suspend to disk
entries are also set.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helps increasing build testing coverage.
To do this, read{write}_relaxed() functions was be replaced with
simple read{write}() variants. Potential "uninitialized variable"
warnings was be fixed if driver compiled without MFD_SYSCON.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replace custom handling of IrDA feature with N_IRDA
line discipline, so IrDA mode can be used with irtty driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The four variants of the synclink driver use the same code in their
open() callback to wait for a port in process of being closed,
using interruptible_sleep_on, which is racy and going away soon.
Making things worse, these functions hold the BTM while doing so,
which means that if we ever enter this code path, we cannot actually
continue since the other thread that is in process of closing the
port can no longer get the BTM.
This addresses both issues by using wait_event_interruptible_tty()
instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
interruptible_sleep_on is generally problematic and we want to get
rid of it. In case of TIOCMIWAIT, that race is actually in user
space and does not get fixed since we can only detect changes after
entering the ioctl handler, but it removes one more caller.
This instance can not be trivially replaced with wait_event, so
I chose to open-code the wait loop using prepare_to_wait/finish_wait.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ARM SoC fixes from Olof Johansson:
"Much smaller batch of fixes this week.
Biggest one is a revert of an OMAP display change that removed some
non-DT pinmux code that was still needed for 3.13 to get DSI displays
to work.
There's also a fix that resolves some misdescribed GPIO controller
resources on shmobile. The rest are mostly smaller fixes, a couple of
MAINTAINERS updates, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
Revert "ARM: OMAP2+: Remove legacy mux code for display.c"
MAINTAINERS: Add keystone clock drivers
MAINTAINERS: Add keystone git tree information
ARM: s3c64xx: dt: Fix boot failure due to double clock initialization
ARM: shmobile: r8a7790: Fix GPIO resources in DTS
irqchip: renesas-intc-irqpin: Fix register bitfield shift calculation
ARM: shmobile: lager: phy fixup needs CONFIG_PHYLIB
Pull firewire fixlet from Stefan Richter:
"A one-liner to reenable WRITE SAME over SBP-2 like in v3.8...v3.12.
Buggy targets which could malfunction when being subjected to this
command are already sufficiently protected by a scsi_level check in sd
+ SCSI core"
* tag 'firewire-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: sbp2: bring back WRITE SAME support
Pull SCSI target fixes from Nicholas Bellinger:
"Mostly minor items this time around, the most notable being a FILEIO
backend change to enforce hw_max_sectors based upon the current
block_size to address a bug where large sized I/Os (> 1M) where being
rejected"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
qla2xxx: Fix schedule_delayed_work() for target timeout calculations
iser-target: fix error return code in isert_create_device_ib_res()
iscsi-target: Fix-up all zero data-length CDBs with R/W_BIT set
target: Remove write-only stats fields and lock from struct se_node_acl
iscsi-target: return -EINVAL on oversized configfs parameter
Pull AIO leak fixes from Ben LaHaise:
"I've put these two patches plus Linus's change through a round of
tests, and it passes millions of iterations of the aio numa
migratepage test, as well as a number of repetitions of a few simple
read and write tests.
The first patch fixes the memory leak Kent introduced, while the
second patch makes aio_migratepage() much more paranoid and robust"
* git://git.kvack.org/~bcrl/aio-next:
aio/migratepages: make aio migrate pages sane
aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
Since commit 36bc08cc01 ("fs/aio: Add support to aio ring pages
migration") the aio ring setup code has used a special per-ring backing
inode for the page allocations, rather than just using random anonymous
pages.
However, rather than remembering the pages as it allocated them, it
would allocate the pages, insert them into the file mapping (dirty, so
that they couldn't be free'd), and then forget about them. And then to
look them up again, it would mmap the mapping, and then use
"get_user_pages()" to get back an array of the pages we just created.
Now, not only is that incredibly inefficient, it also leaked all the
pages if the mmap failed (which could happen due to excessive number of
mappings, for example).
So clean it all up, making it much more straightforward. Also remove
some left-overs of the previous (broken) mm_populate() usage that was
removed in commit d6c355c7da ("aio: fix race in ring buffer page
lookup introduced by page migration support") but left the pointless and
now misleading MAP_POPULATE flag around.
Tested-and-acked-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The arbitrary restriction on page counts offered by the core
migrate_page_move_mapping() code results in rather suspicious looking
fiddling with page reference counts in the aio_migratepage() operation.
To fix this, make migrate_page_move_mapping() take an extra_count parameter
that allows aio to tell the code about its own reference count on the page
being migrated.
While cleaning up aio_migratepage(), make it validate that the old page
being passed in is actually what aio_migratepage() expects to prevent
misbehaviour in the case of races.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
e34ecee2ae reworked the percpu reference
counting to correct a bug trinity found. Unfortunately, the change lead
to kioctxes being leaked because there was no final reference count to
put. Add that reference count back in to fix things.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Cc: stable@vger.kernel.org
Commit 1bf49dd4be ("./Makefile: export initial ramdisk compression
config option") started setting the INITRD_COMPRESS environment variable
depending on which decompression models the kernel had available.
That is completely broken.
For example, we by default have CONFIG_RD_LZ4 enabled, and are able to
decompress such an initrd, but the user tools to *create* such an initrd
may not be availble. So trying to tell dracut to generate an
lz4-compressed image just because we can decode such an image is
completely inappropriate.
Cc: J P <ppandit@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull xfs bugfixes from Ben Myers:
"This contains fixes for some asserts
related to project quotas, a memory leak, a hang when disabling group or
project quotas before disabling user quotas, Dave's email address, several
fixes for the alignment of file allocation to stripe unit/width geometry, a
fix for an assertion with xfs_zero_remaining_bytes, and the behavior of
metadata writeback in the face of IO errors.
Details:
- fix memory leak in xfs_dir2_node_removename
- fix quota assertion in xfs_setattr_size
- fix quota assertions in xfs_qm_vop_create_dqattach
- fix for hang when disabling group and project quotas before
disabling user quotas
- fix Dave Chinner's email address in MAINTAINERS
- fix for file allocation alignment
- fix for assertion in xfs_buf_stale by removing xfsbdstrat
- fix for alignment with swalloc mount option
- fix for "retry forever" semantics on IO errors"
* tag 'xfs-for-linus-v3.13-rc5' of git://oss.sgi.com/xfs/xfs:
xfs: abort metadata writeback on permanent errors
xfs: swalloc doesn't align allocations properly
xfs: remove xfsbdstrat error
xfs: align initial file allocations correctly
MAINTAINERS: fix incorrect mail address of XFS maintainer
xfs: fix infinite loop by detaching the group/project hints from user dquot
xfs: fix assertion failure at xfs_setattr_nonsize
xfs: fix false assertion at xfs_qm_vop_create_dqattach
xfs: fix memory leak in xfs_dir2_node_removename
Commit 597d795a2a ('mm: do not allocate page->ptl dynamically, if
spinlock_t fits to long') restructures some allocators that are compiled
even if USE_SPLIT_PTLOCKS arn't used. It results in compilation
failure:
mm/memory.c:4282:6: error: 'struct page' has no member named 'ptl'
mm/memory.c:4288:12: error: 'struct page' has no member named 'ptl'
Add in the missing ifdef.
Fixes: 597d795a2a ('mm: do not allocate page->ptl dynamically, if spinlock_t fits to long')
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARC fix from Vineet Gupta:
"Fix busted syscall table due to unistd header inclusion issue"
* tag 'arc-fixes-for-3.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
Stephen Warren
Mark Deneen
Marek Roszko
Qipan Li
Alexander Shiyan
Arnd Bergmann
Paul Gortmaker
Greg Kroah-Hartman
Linus Torvalds
Benjamin LaHaise
Olof Johansson