Move s3fb_get_tilemax to svgalib.c as svga_get_tilemax, because it reports
limitation of other code from svgalib (svga_settile, svga_tilecopy, ...)
Limit font width to 8 pixels in 4 bpp mode.
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch disables a memory clock setting if a board has been initialized by
BIOS. This allows using the memory clock set by manufacturer of the board.
This patch also sets default clock for 3dlabs Permedia 2V reference board's
clock to 75MHz (BIOS setting for EONtronic Permedia 2Vboard), because the
default 83MHz can be too high.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resets transparency settings when depth changes. Otherwise the 16
and 24-bit modes work incorrectly after switching from 32-bit mode.
Signed-off-by: Krzysztof Helt < krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Check the console-to-fb mapping in fbcon_get_requirement(), otherwise the
value returned may not be valid for the driver.
- Minor cleanup
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up exit patch of fb_set_var():
- consolidate all return values into a single local variable
- ensure that return values are valid error codes
- fix fb_set_var() returning success when fb_check_caps() failed
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorganize atyfb clock init code so command line clock overrides are effective
for all chips. The old code would silently ignore some of the command line
clock overrides with some chips.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1) sets 'palette access disabled' during read from AR10.
This is usually documented as needed for access AR01-AR0F,
but on ARK Logic card it is needed for AR10 (otherwise read
returns some nonsence and save_vga_text() returns before do
anything).
2) do not restore AR10, because it was not changed during
3) remove modification of misc reg:
/* force graphics mode */
vga_w(state->vgabase, VGA_MIS_W, misc | 1);
as comment is misleading - LSB of misc reg does not set/reset graphics
mode, but set color/mono adresses of CRT and some other regs.
but these regs are not used during save/restore fonts.
(it worked even when (misc | 1) was replaced by (misc & ~1) ).
Signed-off-by: Ondrej Zajicek <santiago@crfreenet.org>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Implement fb_get_caps(). This will allow the driver to tell upper layer that
it can only support 256 8x16 bitmaps when in tileblitting mode
(var->bits_per_pixel == 0);
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Check if the mode can properly display the screen. This will be needed by
drivers where the capability is not constant with each mode. The function
fb_set_var() will query fbcon the requirement, then it will query the driver
(via a new hook fb_get_caps()) its capability. If the driver's capability
cannot handle fbcon's requirement, then fb_set_var() will fail.
For example, if a particular driver supports 2 modes where:
mode1 = can only display 8x16 bitmaps
mode2 = can display any bitmap
then if current mode = mode2 and current font = 12x22
fbset <mode1> /* mode1 cannot handle 12x22 */
fbset will fail
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds restrictions to calculations of m, n and p factors
which sets the pixclock for the Permedia 2V. I found during tests
that synchronization is unstable if m (divisor) is bigger than
half of the n (numerator). The patch disallows such settings
combination.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Switch to pci_get refcounting APIs
[adaplas]
Fix a long-standing bug where the return value of
pci_find_slot()/pci_get_bus_and_slot() is ignored.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some drivers may reset the var->activate field on fb_check_var(). This can
lead to undefined behavior. For example, doing fbset -a <option> with vga16fb
will only modify the active console instead of modifying all.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fontmaps can be 256 or 512 in length. The only driver that can do tileblitting
can only handle 256 characters. Check for this when setting the font.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a tile method, fb_get_tilemax(), that returns the maximum length of
the tile map (or font map). This is needed by s3fb which can only handle
256 characters.
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ondrej Zajicek
Krzysztof Helt
Antonino A. Daplas
Adrian Bunk
Matthias Kaehlcke
Ville Syrjala
Dave Jones
Alan Cox
Alan Hourihane