This makes the various rings more consistent by removing the anomalous
handing of the rendering ring execbuffer dispatch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
... so that upon first use after resume we will reacquire the fence reg.
Reported-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As the error occurred on the current object, it means that its state was
not changed and so it should be excluded from the unwind.
Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We don't track gpu flush request in any special way. So even with
obj->write_domain == 0, a gpu flush might be outstanding but no
yet executed. Even worse, the latest request might use the object
only for reading. So and unconditional call to object_wait_rendering
is needed for !pipelined.
Hence revert that patch fully and untangle the flushing from the
synchronization again.
Reported-by: Keith Packard <keithp@keithp.com>
Tested-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Besides the minimal improvement in reducing the execbuffer overhead, the
real benefit is clarifying a few routines.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
A number of dragons have been seen lurking within the execbuffer code.
The first step is then to isolate them from the rest and begin to
scrutinise them in depth. Suggested by Daniel Vetter.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Simply remove our accounting of objects inside the aperture, keeping
only track of what is in the aperture and its current usage. This
removes the over-complication of BUGs that were attempting to keep the
accounting correct and also removes the overhead of the accounting on
the hot-paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
With KMS, we can simply relinquish the fence when we idle the GPU and
reassign it upon first use.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Commit d09c23de intended to add a 30ms delay to give the ADD time to
detect any TVs connected. However, it used the sdvo->is_tv flag to do so
which is dependent upon the previous detection result and not whether the
output supports TVs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Avoid evicting buffers that will be used later in the batch in order to
make room for the initial buffers by pinning all bound buffers in a
single pass before binding (and evicting for) fresh buffer.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
On a few devices, like the Mac Mini, the CRT DDC pins are shared between
the analog connector and the digital connector. In this scenario, rely
on the EDID to determine if a digital panel is connected to the digital
connector.
Reported-and-tested-by: Tino Keitel <tino.keitel@tikei.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This used to check the precondition that all fences were to be located
in a mappable area, redundant now as those two parameters are combined
into one.
After pinning, we assert that the buffer is bound into the desired
region.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The pipe control object is allocated by the device for the sole use of the
render ringbuffer. Move this detail from the general code to the render
ring buffer initialisation.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Having seen the effects of erroneous fencing on the batchbuffer, a
useful sanity check is to record the fence registers at the time of an
error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Chris Wilson
Daniel Vetter
Joe Perches