For UV add the code to create the activate and notify gru message queues.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Define xp_expand_memprotect() and xp_restrict_memprotect() so they can be
tailered to the hardware they are run on.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup
Change UV heartbeat function to use idle_cpu to determine cpu's
"idleness". Realign uv_hub definitions.
Signed-of-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: start per CPU heartbeat LED timers on SGI UV systems
The SGI UV system has no LEDS but uses one of the system controller
regs to indicate the online internal state of the cpu. There is a
heartbeat bit indicating that the cpu is responding to interrupts,
and an idle bit indicating whether the cpu is idle when the heartbeat
interrupt occurs. The current period is one second.
When a cpu panics, an error code is written by BIOS to this same reg.
This patchset provides the following:
* x86_64: Add base functionality for writing to the specific SCIR's
for each cpu.
* heartbeat: Invert "heartbeat" bit to indicate the cpu is
"interruptible". If the current thread is the idle thread,
then indicate system is "idle".
* if hotplug enabled, all bits are set (0xff) when the cpu is disabled.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If CONFIG_AMIGA_BUILTIN_SERIAL=m, I get the following warnings:
| drivers/char/amiserial.c: At top level:
| drivers/char/amiserial.c:2138: warning: data definition has no type or storage class
| drivers/char/amiserial.c:2138: warning: type defaults to 'int' in declaration of 'console_initcall'
| drivers/char/amiserial.c:2138: warning: parameter names (without types) in function declaration
| drivers/char/amiserial.c:2134: warning: 'amiserial_console_init' defined but not used
because console_initcall() is not defined (nor really sensible) in the
modular case.
So disable serial console support if the driver is modular.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit f337b9c583 ("epoll: drop
unnecessary test") Thomas found that there is an unnecessary (always
true) test in ep_send_events(). The callback never inserts into
->rdllink while the send loop is performed, and also does the
~EP_PRIVATE_BITS test. Given we're holding the mutex during this time,
the conditions tested inside the loop are always true.
HOWEVER.
The test "!ep_is_linked(&epi->rdllink)" wasn't there because we insert
into ->rdllink, but because the send-events loop might terminate before
the whole list is scanned (-EFAULT).
In such cases, when the loop terminates early, and when a (leftover)
file received an event while we're performing the lockless loop, we need
such test to avoid to double insert the epoll items. The list_splice()
done a few steps below, will correctly re-insert the ones that were left
on "txlist".
This should fix the kenrel.org bugzilla entry 11831.
Signed-off-by: Davide Libenzi <davidel@xmailserver.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some userland apps seem to pass in a "0" for the seconds, and several
seconds worth of usecs to select(). The old kernels accepted this just
fine, so the new kernels must too.
However, due to the upscaling of the microseconds to nanoseconds we had
some cases where we got math overflow, and depending on the GCC version
(due to inlining decisions) that actually resulted in an -EINVAL return.
This patch fixes this by adding the excess microseconds to the seconds
field.
Also with thanks to Marcin Slusarz for spotting some implementation bugs
in the diagnostics patches.
Reported-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The default for the regulatory compatibility option is wrong;
if you picked the default you ended up with a non-functional wifi
system (at least I did on Fedora 9 with iwl4965).
I don't think even the October 2008 releases of the various distros
has the new userland so clearly the default is wrong, and also
we can't just go about deleting this in 2.6.29...
Change the default to "y" and also adjust the config text a little to
reflect this.
This patch fixes regression #11859
With thanks to Johannes Berg for the diagnostics
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
/scratch/sfr/next/kernel/cgroup.c: In function 'cgroup_tasks_start':
/scratch/sfr/next/kernel/cgroup.c:2107: warning: unused variable 'i'
Introduced in commit cc31edceee "cgroups:
convert tasks file to use a seq_file with shared pid array".
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'hwmon-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6:
hwmon: (abituguru3) enable DMI probing feature on AW9D-MAX
hwmon: (abituguru3) Cosmetic whitespace fixes
hwmon: (adt7473) Fix voltage conversion routines
hwmon: (lm90) Add support for the LM99 16 degree offset
hwmon: (lm90) Fix handling of hysteresis value
hwmon-vid: Add support for AMD family 10h CPUs
hwmon: (w83781d) Fix linking when built-in
This reverts commit 7bf6bf4803.
The code has both a short existence and an increasing track of failures
despite some work to amend it for -rc1. It is not just a matter of
reading the eeprom: sometimes the eeprom is read correctly, then the mac
address is not written correctly back into the mac registers.
Some chipsets seem to work reliably but it is not clear at this point if
the code can simply be made to work on a per-chipset basis and post -rc1
is not the place where I want to experiment these things.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) semicolon before the function body is a bad idea
b) it's const struct foo, not struct const foo
c) incidentally, it's ecard_remove_driver(), not ecard_unregister_driver()
d) compiling is occasionally useful.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If you use KCONFIG_ALLCONFIG (even with empty file) you get broken
allmodconfig/allyesconfig; CONFIG_MODULES gets turned off, with obvious
massive fallout.
Breakage had been introduced when conf_set_all_new_symbols() got used
for allmodconfig et.al.
What happens is that sym_calc_value(modules_sym) done in
conf_read_simple() sets SYMBOL_VALID on both modules_sym and MODULES.
When we get to conf_set_all_new_symbols(), we set sym->def[S_DEF_USER]
on everything, but it has no effect on sym->curr for the symbols that
already have SYMBOL_VALID - these are stuck.
Solution: use sym_clear_all_valid() in there. Note that it makes
reevaluation of modules_sym redundant - sym_clear_all_valid() will do
that itself.
[ Fixes http://bugzilla.kernel.org/show_bug.cgi?id=11512, says Alexey ]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As the probable result of zealous copy/pasting, many supported boards
contain sensor names with trailing whitespace. Though this is not a
huge problem, it is inconsistent with other sensor names, and with
other similar hwmon drivers.
Additionally, the DMI nag message added in 2.6.27 was missing a
space between two sentence fragments -- might as well clean that up
too.
Doesn't alter any kernel text, just data.
Signed-off-by: Alistair John Strachan <alistair@devzero.co.uk>
Reported-by: Justin Piszcz <jpiszcz@lucidpixels.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix voltage conversion routines. Based on an earlier patch from
Paulius Zaleckas.
According to the datasheet voltage is scaled with resistors and
value 192 is nominal voltage. 0 is 0V.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Cc: Darrick J. Wong <djwong@us.ibm.com>
The LM99 differs from the LM86, LM89 and LM90 in that it reports
remote temperatures (temp2) 16 degrees lower than they really are. So
far we have been cheating and handled this in userspace but it really
should be handled by the driver directly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
There are several problems in the way the hysteresis value is handled
by the lm90 driver:
* In show_temphyst(), specific handling of the MAX6646 is missing, so
the hysteresis is reported incorrectly if the critical temperature
is over 127 degrees C.
* In set_temphyst(), the new hysteresis register value is written to
the chip but data->temp_hyst isn't updated accordingly, so there is
a short period of time (up to 2 seconds) where the old hystereris
value will be returned while the new one is already active.
* In set_temphyst(), the critical temperature which is used as a base
to compute the value of the hysteresis register lacks
device-specific handling. As a result, the value of the hysteresis
register might be incorrect for the ADT7461 and MAX6646 chips.
Fix these 3 bugs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Nate Case <ncase@xes-inc.com>
The AMD family 10h CPUs use the same VID decoding table as the family
0Fh CPUs.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
When w83781d is built-in, the final links fails with the following vague error
message:
`.exit.text' referenced in section `.init.text' of drivers/built-in.o: defined
in discarded section `.exit.text' of drivers/built-in.o
w83781d_isa_unregister() cannot be marked __exit, as it's also called from
sensors_w83781d_init(), which is marked __init.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Dean Nelson
Russ Anderson
Mike Travis
Ingo Molnar
Linus Torvalds
Geert Uytterhoeven
Davide Libenzi
Arjan van de Ven
Stephen Rothwell
Francois Romieu
Al Viro
Alistair John Strachan
Jean Delvare