This improves AEN handler for Host Network Controller Driver Status
Change (HNCDSC):
* The channel's lock should be hold when accessing its state.
* Do failover when host driver isn't ready.
* Configure channel when host driver becomes ready.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was found on BCM5718 which has two NCSI channels in one
package: C0 and C1. C0 is in link-up state while C1 is in link-down
state. C0 is chosen as active channel until unplugging and plugging
C0's cable: On unplugging C0's cable, LSC (Link State Change) AEN
packet received on C0 to report link-down event. After that, C1 is
chosen as active channel. LSC AEN for link-up event is lost on C0
when plugging C0's cable back. We lose the network even C0 is usable.
This resolves the issue by recording the (hot) channel that was ever
chosen as active one. The hot channel is chosen to be active one
if none of available channels in link-up state. With this, C0 is still
the active one after unplugging C0's cable. LSC AEN packet received
on C0 when plugging its cable back.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was found on BCM5718 which has two NCSI channels in one
package: C0 and C1. Both of them are connected to different LANs,
means they are in link-up state and C0 is chosen as the active one
until resetting BCM5718 happens as below.
Resetting BCM5718 results in LSC (Link State Change) AEN packet
received on C0, meaning LSC AEN is missed on C1. When LSC AEN packet
received on C0 to report link-down, it fails over to C1 because C1
is in link-up state as software can see. However, C1 is in link-down
state in hardware. It means the link state is out of synchronization
between hardware and software, resulting in inappropriate channel (C1)
selected as active one.
This resolves the issue by sending separate GLS (Get Link Status)
commands to all channels in the package before trying to do failover.
The last link states of all channels in the package are retrieved.
With it, C0 (not C1) is selected as active one as expected.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several if/else statements in the state machine implemented
by switch/case in ncsi_suspend_channel() to avoid duplicated code. It
makes the code a bit hard to be understood.
This drops if/else statements in ncsi_suspend_channel() to improve the
code readability as Joel Stanley suggested. Also, it becomes easy to
add more states in the state machine without affecting current code.
No logical changes introduced by this.
Suggested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stats_update callback is called by NIC drivers doing hardware
offloading of the mirred action. Lastuse is passed as argument
to specify when the stats was actually last updated and is not
always the current time.
Fixes: 9798e6fe4f ('net: act_mirred: allow statistic updates from offloaded actions')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SwitchX2 firmware does not implement reset done yet. Moreover, when
busy-polled for ready magic, that slows down firmware and reset takes
longer than the defined timeout, causing initialization to fail.
So restore the previous behaviour and just sleep in this case.
Fixes: 233fa44bd6 ("mlxsw: pci: Implement reset done check")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating an ethernet port fails, we must move the port to disable,
otherwise putting the port in switch partition 0 (ETH) or 1 (IB) will
always fails.
Fixes: 31557f0f97 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function return value is not checked anywhere. Also, the warning
causes huge slowdown when removing large number of FIB entries which
were not offloaded, because of ordering issue. Ido's preparing
a patchset to fix the ordering issue, but that is definitelly not
net tree material.
Fixes: b45f64d16d ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By a mistake, there is tree index 0 passed to RALTB. Should be
MLXSW_SP_LPM_TREE_MIN.
Fixes: b45f64d16d ("mlxsw: spectrum_router: Use FIB notifications instead of switchdev calls")
Reported-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit commit 7086605a6a ("stmmac: fix error check when init ptp")
breaks the procedure added by the
commit efee95f42b ("ptp_clock: future-proofing drivers against PTP
subsystem becoming optional")
So this patch tries to re-import the logic added by the latest
commit above: it makes sense to have the stmmac_ptp_register
as void function and, inside the main, the stmmac_init_ptp can fails
in case of the capability cannot be supported by the HW.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Cc: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Nicolas Pitre <nico@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b2fb4f54ec ("tcp: uninline tcp_prequeue()") we no longer
access sysctl_tcp_low_latency from a module.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offload flag is a status flag and should not be used by
FIB semantics for comparison.
Fixes: 37ed949369 ("rtnetlink: add RTNH_F_EXTERNAL flag for fib offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We recently got the following warning after setting up a vlan device on
top of an offloaded bridge and executing 'bridge link':
WARNING: CPU: 0 PID: 18566 at drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c:81 mlxsw_sp_port_orig_get.part.9+0x55/0x70 [mlxsw_spectrum]
[...]
CPU: 0 PID: 18566 Comm: bridge Not tainted 4.8.0-rc7 #1
Hardware name: Mellanox Technologies Ltd. Mellanox switch/Mellanox switch, BIOS 4.6.5 05/21/2015
0000000000000286 00000000e64ab94f ffff880406e6f8f0 ffffffff8135eaa3
0000000000000000 0000000000000000 ffff880406e6f930 ffffffff8108c43b
0000005106e6f988 ffff8803df398840 ffff880403c60108 ffff880406e6f990
Call Trace:
[<ffffffff8135eaa3>] dump_stack+0x63/0x90
[<ffffffff8108c43b>] __warn+0xcb/0xf0
[<ffffffff8108c56d>] warn_slowpath_null+0x1d/0x20
[<ffffffffa01420d5>] mlxsw_sp_port_orig_get.part.9+0x55/0x70 [mlxsw_spectrum]
[<ffffffffa0142195>] mlxsw_sp_port_attr_get+0xa5/0xb0 [mlxsw_spectrum]
[<ffffffff816f151f>] switchdev_port_attr_get+0x4f/0x140
[<ffffffff816f15d0>] switchdev_port_attr_get+0x100/0x140
[<ffffffff816f15d0>] switchdev_port_attr_get+0x100/0x140
[<ffffffff816f1d6b>] switchdev_port_bridge_getlink+0x5b/0xc0
[<ffffffff816f2680>] ? switchdev_port_fdb_dump+0x90/0x90
[<ffffffff815f5427>] rtnl_bridge_getlink+0xe7/0x190
[<ffffffff8161a1b2>] netlink_dump+0x122/0x290
[<ffffffff8161b0df>] __netlink_dump_start+0x15f/0x190
[<ffffffff815f5340>] ? rtnl_bridge_dellink+0x230/0x230
[<ffffffff815fab46>] rtnetlink_rcv_msg+0x1a6/0x220
[<ffffffff81208118>] ? __kmalloc_node_track_caller+0x208/0x2c0
[<ffffffff815f5340>] ? rtnl_bridge_dellink+0x230/0x230
[<ffffffff815fa9a0>] ? rtnl_newlink+0x890/0x890
[<ffffffff8161cf54>] netlink_rcv_skb+0xa4/0xc0
[<ffffffff815f56f8>] rtnetlink_rcv+0x28/0x30
[<ffffffff8161c92c>] netlink_unicast+0x18c/0x240
[<ffffffff8161ccdb>] netlink_sendmsg+0x2fb/0x3a0
[<ffffffff815c5a48>] sock_sendmsg+0x38/0x50
[<ffffffff815c6031>] SYSC_sendto+0x101/0x190
[<ffffffff815c7111>] ? __sys_recvmsg+0x51/0x90
[<ffffffff815c6b6e>] SyS_sendto+0xe/0x10
[<ffffffff817017f2>] entry_SYSCALL_64_fastpath+0x1a/0xa4
The problem is that the 8021q module propagates the call to
ndo_bridge_getlink() via switchdev ops, but the switch driver doesn't
recognize the netdev, as it's not offloaded.
While we can ignore calls being made to non-bridge ports inside the
driver, a better fix would be to push this check up to the switchdev
layer.
Note that these ndos can be called for non-bridged netdev, but this only
happens in certain PF drivers which don't call the corresponding
switchdev functions anyway.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes a panic when calling eth_get_headlen(). Noticed on i40e driver.
Fixes: d5709f7ab7 ("flow_dissector: For stripped vlan, get vlan info from skb->vlan_tci")
Signed-off-by: Eric Garver <e@erig.me>
Reviewed-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some rare configurations, we get a warning about the 'index' variable
being used without an initialization:
drivers/net/ethernet/rocker/rocker_ofdpa.c: In function ‘ofdpa_port_fib_ipv4.isra.16.constprop’:
drivers/net/ethernet/rocker/rocker_ofdpa.c:2425:92: warning: ‘index’ may be used uninitialized in this function [-Wmaybe-uninitialized]
This is a false positive, the logic is just a bit too complex for gcc
to follow here. Moving the intialization of 'index' a little further
down makes it clear to gcc that the function always returns an error
if it is not initialized.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hdr_offset variable is only if we deal with a TCP or UDP packet,
but as the check surrounding its usage tests for skb_is_gso()
instead, the compiler has no idea if the variable is initialized
or not at that point:
drivers/net/hyperv/netvsc_drv.c: In function ‘netvsc_start_xmit’:
drivers/net/hyperv/netvsc_drv.c:494:42: error: ‘hdr_offset’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This adds an additional check for the transport type, which
tells the compiler that this path cannot happen. Since the
get_net_transport_info() function should always be inlined
here, I don't expect this to result in additional runtime
checks.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc found a reference to an uninitialized variable in the error handling
of bcm_enet_open, introduced by a recent cleanup:
drivers/net/ethernet/broadcom/bcm63xx_enet.c: In function 'bcm_enet_open'
drivers/net/ethernet/broadcom/bcm63xx_enet.c:1129:2: warning: 'phydev' may be used uninitialized in this function [-Wmaybe-uninitialized]
This makes the use of that variable conditional, so we only reference it
here after it has been used before. Unlike my normal patches, I have not
build-tested this one, as I don't currently have mips test in my
randconfig setup.
Fixes: 625eb8667d ("net: ethernet: broadcom: bcm63xx: use phydev from struct net_device")
Cc: Philippe Reynes <tremyfr@gmail.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
reuseport_add_sock() is not used from a module,
no need to export it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for the MTU to be changed during the initialization
process with the VNIC Server. Ensure that the net device is updated
to reflect the new MTU.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increment driver version to reflect features that have
been added since release.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Satish reported a problem with the perm multicast router ports not getting
reenabled after some series of events, in particular if it happens that the
multicast snooping has been disabled and the port goes to disabled state
then it will be deleted from the router port list, but if it moves into
non-disabled state it will not be re-added because the mcast snooping is
still disabled, and enabling snooping later does nothing.
Here are the steps to reproduce, setup br0 with snooping enabled and eth1
added as a perm router (multicast_router = 2):
1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping
2. $ ip l set eth1 down
^ This step deletes the interface from the router list
3. $ ip l set eth1 up
^ This step does not add it again because mcast snooping is disabled
4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping
5. $ bridge -d -s mdb show
<empty>
At this point we have mcast enabled and eth1 as a perm router (value = 2)
but it is not in the router list which is incorrect.
After this change:
1. $ echo 0 > /sys/class/net/br0/bridge/multicast_snooping
2. $ ip l set eth1 down
^ This step deletes the interface from the router list
3. $ ip l set eth1 up
^ This step does not add it again because mcast snooping is disabled
4. $ echo 1 > /sys/class/net/br0/bridge/multicast_snooping
5. $ bridge -d -s mdb show
router ports on br0: eth1
Note: we can directly do br_multicast_enable_port for all because the
querier timer already has checks for the port state and will simply
expire if it's in blocking/disabled. See the comment added by
commit 9aa6638216 ("bridge: multicast: add a comment to
br_port_state_selection about blocking state")
Fixes: 561f1103a2 ("bridge: Add multicast_snooping sysfs toggle")
Reported-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unused but set variable icsk in listening_get_next to fix the
following GCC warning when building with 'W=1':
net/ipv4/tcp_ipv4.c: In function ‘listening_get_next’:
net/ipv4/tcp_ipv4.c:1890:31: warning: variable ‘icsk’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gavin Shan
Paul Blakey
Jiri Pirko
Elad Raz
Giuseppe CAVALLARO
Eric Dumazet
Ido Schimmel
Eric Garver
Wei Yongjun
Arnd Bergmann
Thomas Falcon
Nikolay Aleksandrov
Tobias Klauser