Allow a master interface to be specified as one of the parameters when
creating a new interface via rtnl_newlink. Previously this would
require invoking interface creation, waiting for it to complete, and
then separately binding that new interface to a master.
In particular, this is used when creating a macvlan child interface for
VRRP in a VRF configuration, allowing the interface creator to specify
directly what master interface should be inherited by the child,
without having to deal with asynchronous complications and potential
race conditions.
Signed-off-by: Theuns Verwoerd <theuns.verwoerd@alliedtelesis.co.nz>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-02-01
1) Some typo fixes, from Alexander Alemayhu.
2) Don't acquire state lock in get_mtu functions.
The only rece against a dead state does not matter.
From Florian Westphal.
3) Remove xfrm4_state_fini, it is unused for more than
10 years. From Florian Westphal.
4) Various rcu usage improvements. From Florian Westphal.
5) Properly handle crypto arrors in ah4/ah6.
From Gilad Ben-Yossef.
6) Try to avoid skb linearization in esp4 and esp6.
7) The esp trailer is now set up in different places,
add a helper for this.
8) With the upcomming usage of gro_cells in IPsec,
a gro merged skb can have a secpath. Drop it
before freeing or reusing the skb.
9) Add a xfrm dummy network device for napi. With
this we can use gro_cells from within xfrm,
it allows IPsec GRO without impact on the generic
networking code.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał Miłecki says:
====================
net-next: use one struct bgmac & add PHY support
This patchset adds support for initializing PHY using PHY subsystem.
It's required e.g. for wireless access point devices that use bgmac
supported Ethernet device connected to some external PHY.
Implementing this required accessing phydev in bcma specific code which
wasn't possible with core code allocating struct bgmac on its own. This
is why I needed to modify alloc_etherdev usage first.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for using bgmac with PHYs supported by standalone PHY
drivers. Having any PHY initialization in bgmac is hacky and shouldn't
be extended but rather removed if anyone has hardware to test it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding struct bcma_mdio was a workaround for bcma code not having access
to the struct bgmac used in the core code. Now we don't duplicate this
struct we can just use it internally in bcma code.
This simplifies code & allows access to all bgmac driver details from
all places in bcma code.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far were were allocating struct bgmac in 3 places: platform code,
bcma code and shared bgmac_enet_probe function. The reason for this was
bgmac_enet_probe:
1) Requiring early-filled struct bgmac
2) Calling alloc_etherdev on its own in order to use netdev_priv later
This solution got few drawbacks:
1) Was duplicating allocating code
2) Required copying early-filled struct
3) Resulted in platform/bcma code having access only to unused struct
Solve this situation by simply extracting some probe code into the new
bgmac_alloc function.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7318166cac ("net: dsa: bcm_sf2: Add support for
ethtool::rxnfc") added a new object to build: bcm_sf2_cfp.o, but in
doing so, we essentially just built this object and no longer bcm_sf2.o.
Fix this by creating a module named bcm-sf2.ko which links in bcm_sf2.o
and bcm_sf2_cfp.o.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change t4fw_version.h to update latest firmware version
number 1.16.26.0.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Pavel Belous <pavel.s.belous@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
encap_type should be checked to see if it is greater or equal to
the size of array map to fix an off-by-one array size check. This
fixes an array overrun read as detected by static analysis by
CoverityScan, CID#1398883 ("Out-of-bounds-read")
Fixes: 9b41080125 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergei Shtylyov says:
====================
sh_eth: E-DMAC interrupt mask cleanups
Here's a set of 3 patches against DaveM's 'net-next.git' repo. The main goal
of this set is to stop using the bare numbers for the E-DMAC interrupt masks.
[1/3] sh_eth: rename EESIPR bits
[2/3] sh_eth: add missing EESIPR bits
[3/3] sh_eth: stop using bare numbers for EESIPR values
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have almost all EESIPR bits declared (and those that are
still not are most probably reserved anyway) we can at last replace the
bare numbers used for 'sh_eth_cpu_data::eesipr_value' initializers with
the bit names ORed together...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SH77{34|63} manuals describe more EESIPR bits than the current
driver. Declare the new bits with the end goal of using the bit names
instead of the bare numbers for the 'sh_eth_cpu_data::eesipr_value'
initializers...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the commit b0ca2a21f7 ("sh_eth: Add support of SH7763 to sh_eth")
the *enum* declaring the EESIPR bits (interrupt mask) went out of sync with
the *enum* declaring the EESR bits (interrupt status) WRT bit naming and
formatting. I'd like to restore the consistency by using EESIPR as the bit
name prefix, renaming the *enum* to EESIPR_BIT, and (finally) renaming the
bits according to the available Renesas SH77{34|63} manuals; additionally,
reconstruct couple names using the EESR bit declaration above...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gregory CLEMENT says:
====================
dsa: Add support for the ethernet switch on the ESPRESSObin
This set of patches adds support for the Marvell Ethernet Topaz switch
family (88E6141/88E6341) which is found on the ESPRESSObin. With this
series the network is usable on this board.
As usual, I rebased the series on the very last net-next/master. In
this series there is no temperature support which need some patches
form Andrew Lunn.
As soon as Andrew Lunn will post the needed patch I will send a patch
to enable the temperature support.
Changelog:
v6 -> v7:
- rebased on net-next/master (5b8784aaf2)
- Fixed the wrong age time coeff from 15s to 3.75s.
- Remove support for temperature sensor
v5 -> v6:
- rebased on net-next/master (d140199af5)
- Fix the redundant check on mv88e6xxx_6341_family (reported by Julia
Lawall)
- Add support for the 88E6141
- Move support for temperature sensor in the phy part
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces.
It belongs to the Topaz family and unlike the 88E6341 it does not have
a TCAM.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6341 device is single-chip, 6-port Ethernet switch with
four integrated 10/100/1000Mbps Ethernet transceivers and one high speed
SerDes interfaces. It is partially compatible with switches of family
88E6352 and switches of family 88E6390.
This commit adds an initial support for this switch by describing its
capabilities to the driver and introducing a new family.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell ethernet switches have internal ethernet transceivers with
hardcoded phy addresses. These addresses can be greater than the number
of ports or its value might be different than the associated port number.
This is for example the case for MV88E6341 that has 6 ports and internal
Port 1 to Port4 PHYs mapped at SMI addresses from 0x11 to 0x14.
This commits fixes the issue by removing the condition in MDIO callbacks.
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Say we got really unlucky and these failed on the last iteration, then
it could lead to a use after free bug.
Fixes: cd6851f303 ("smc: remote memory buffers (RMBs)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: Port mirroring support
This patch series adds support for port mirroring in the two
Broadcom switch drivers. The major part of the functional are actually with
the plumbing between tc and the drivers.
Changes in v5:
- Added Jiri's Reviewed-by tag to first patch
- rebase against latest net-next/master after bcm_sf2 CFP series
Changes in v4:
- rebased against latest net-next/master after Vivien's changes
Changes in v3:
- removed multiline comments from added structures
- simplify error handling in dsa_slave_add_cls_matchall
Changes in v2:
- fixed filter removal logic to disable the ingress or egress mirroring
when there are no longer ports being monitored in ingress or egress
- removed a stray list_head in dsa_port structure that is not used
Tested using the two iproute2 examples:
tc qdisc add dev eth1 handle ffff: ingress
tc filter add dev eth1 parent ffff: \
matchall skip_sw \
action mirred egress mirror \
dev eth2
tc qdisc add dev eth1 handle 1: root prio
tc filter add dev eth1 parent 1: \
matchall skip_sw \
action mirred egress mirror \
dev eth2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We can use b53_mirror_add and b53_mirror_del because the Starfighter 2
is register compatible in that specific case.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress or egress capture towards the capture
port. Future improvements could include leveraging the divider to allow
less frames to be captured, as well as matching specific MAC DA/SA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definitions for the different Roboswitch registers relevant for
ingress and egress mirroring.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add necessary plumbing at the slave network device level to have switch
drivers implement ndo_setup_tc() and most particularly the cls_matchall
classifier. We add support for two switch operations:
port_add_mirror and port_del_mirror() which configure, on a per-port
basis the mirror parameters requested from the cls_matchall classifier.
Code is largely borrowed from the Mellanox Spectrum switch driver.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Theuns Verwoerd
David S. Miller
Rafał Miłecki
Florian Fainelli
Ganesh Goudar
Alexei Starovoitov
Philippe Reynes
Colin Ian King
Sergei Shtylyov
Gregory CLEMENT
Romain Perier
Dan Carpenter