The # flag in %X means print a 0X prefix. Remove the extra 0x prefix.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to add per-vif TX power capability cap per-packet TX power to vif
configured power if the latter is lower than per-rate TX power and mac80211
per-frame power. Use vif TX power if TPC has been disabled for current the
interface
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure the HW with highest TX power among all vif when HW TPC has been
enabled in order to add support to per-vif TX power capability. Use lowest
configured power among all interfaces when TPC is disabled
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HAL_RETRY_LIMIT_*
RESET_DELAY_8185
RT_IBSS_INT_MASKS
RT_AC_INT_MASKS
NUM_OF_*
BT_*,
MAX_{LINES,BYTES}_*,
*_THREE_WIRE
*_QUEUE related
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
kbuild found out that commit 804e27dee4 ("bcma: support bringing up
bus hosted on PCIe Gen 2") broke the build on m68k:
drivers/bcma/driver_pcie2.c: In function 'bcma_core_pcie2_up':
>> drivers/bcma/driver_pcie2.c:196:2: error: implicit declaration of function 'pcie_set_readrq' [-Werror\
=implicit-function-declaration]
err = pcie_set_readrq(dev, pcie2->reqsize);
^
cc1: some warnings being treated as errors
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set The BT/WLAN priority weights correctly and make sure
that MCI_LNA_TAKE is sent only for cards that share
PA/LNA.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Handle MCI_STATE_INIT_GPM_OFFSET separately and do not
overload ar9003_mci_get_next_gpm_offset() with a special
case.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The LNA_TRANS message needs to be sent only for
chips which have shared PA/LNA.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use a subroutine to enable MCI debug statistics
if it is present in the global configuration.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch makes sure that the antenna configuration
is used properly when setting AR_MCI_TX_CTRL.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The value programmed in the BTCOEX control register
is different for each chip. This patch adds support
for 2-ANT, 1-ANT solutions based on AR9565.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we fail to allocate the sched/gpm buffers when
initializing MCI, we bail out properly. Checking
them in ar9003_mci_reset() is unnecessary, so remove it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Carpenter
Rasmus Villemoes
Lorenzo Bianconi
Priit Laes
Rafał Miłecki
Sujith Manoharan
Geert Uytterhoeven
Kalle Valo