Since 6397 is no need to support interrupt controller,
moving interrupt controller relate property to optional list.
Also adding mt8173 and mt8127 to bindings.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the required group function map and fill it at probe using
the pin capabilities information already present in the driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver for the pin controller present on the IMG Pistachio SoC.
This driver provides pinmux and pinconfig operations as well as GPIO
and IRQ chips for the GPIO banks.
Changes from v4:
- Switched to using gpiochip_add_pin_range().
- Fixed up Kconfig entry.
Changes from v3:
- Addressed review comments from Ezequiel.
Changes from v2:
- Removed module stuff which would be compiled out.
Changes from v1:
- Addressed review comments from Linus.
- Changed compatible string to "img,pistachio-system-pinctrl".
- Look for GPIO sub-nodes by name.
- A couple of bug fixes.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both pconf_get_pin and pconf_set_pin needs to lookup pin cap based
on the pin number. Create a common helper function that both
functions can use that also handles the case where no pin number is
found in the pins array.
This also fixes a small bug in pconf_get_pin where pconf_get_i2c0
would use the pins array index rather than the pin number.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Sunrisepoint-H is a desktop version of the PCH (Platform Controller
Hub). It has slightly different pin configuration compared to the LP
version. This patch adds support for Sunrisepoint-H to the existing
pinctrl-sunrisepoint.c driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As of commit 9d07d414d4 ("ARM: shmobile: r8a73a4: ape6evm: Remove
legacy platform"), r8a73a4 is only supported in generic DT-only ARM
multi-platform builds. The driver doesn't need to match platform
devices by name anymore, hence remove the corresponding
platform_device_id entry.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_domain_ops are not modified by the driver and the irqdomain core
code accepts pointer to a const data.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The old format to define pinctrl settings for imx in DT has two
hierarchy levels. The first level are function device nodes. The second
level are pingroups which contain a property fsl,pins. The original
intention was to define all pin functions in a single dtsi file and just
reference the correct ones in the board files.
This idea was rejected some time ago leading to the current design to
have all the pinfunctions defined in the board files. So we don't need
the function device nodes anymore.
This patch changes the pinctrl driver to accept devicetrees which do not
have the first hierarchy level, function device nodes. For example
karo-tx25 already has such a devicetree. Old devicetrees are still
parsed and supported.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since SCLK, MISO and MOSI are the only mandatory signals at Zynq's SPI
interfaces, SS0, SS1 and SS2 have to be configured separately as they may
be used as simple GPIO lines.
This, of course, has to be considered in the devicetree, so pin controller
configuration for e.g. an SPI0 using SS0 and SS1 only might look like the
following snippet (derived from the example of chapter "17.5.3
MIO/EMIO" Routing of Zynq-7000 TRM UG585). So MIO20 can now be used
as GPIO instead of being occupied by SPI0 SS2 function. Note the separate
pinmux function for the slave select signals:
pinctrl_spi0_default: spi0-default {
mux_spi {
function = "spi0";
groups = "spi0_0_grp";
};
mux_ss {
function = "spi0_ss";
groups = "spi0_0_ss0_grp", "spi0_0_ss1_grp";
}
conf-output {
pins = "MIO16", "MIO21";
slew-rate = <0>;
bias-disable;
low-power-disable;
io-standard = <1>;
};
conf-input {
pins = "MIO17";
slew-rate = <0>;
bias-high-impedance;
low-power-disable;
io-standard = <1>;
};
conf-select {
pins = "MIO18", "MIO19";
slew-rate = <0>;
bias-pull-up;
low-power-disable;
io-standard = <1>;
};
};
pinctrl_gpio0_default {
mux {
function = "gpio0";
groups = "gpio0_20_grp"
};
conf {
pins = "MIO20";
slew-rate = <0>;
bias-pull-up;
low-power-disable;
io-standard = <1>;
};
};
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Assign GPIO chip and irqchip to the GPIO container dynamically,
so we can set a unique name for each GPIO irqchip and see what
chip the hwirq offset actually relates to.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This activates strict mode muxing for the Nomadik pin controllers,
as these do not allow GPIO and functions to use the same pin
simultaneously.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While the pinmux_ops are ideally just a vtable for pin mux
calls, the "strict" setting belongs so intuitively with the
pin multiplexing that we should move it here anyway. Putting
it in the top pinctrl_desc makes no sense.
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Disallow simultaneous use of the the GPIO and peripheral mux
functions by setting a flag "strict" in struct pinctrl_desc.
The blackfin pinmux and gpio controller doesn't allow user to
set up a pin for both GPIO and peripheral function. So, add flag
strict in struct pinctrl_desc to check both gpio_owner and
mux_owner before approving the pin request.
v2-changes:
- if strict flag is set, check gpio_owner and mux_onwer in if and
else clause
v3-changes:
- add kerneldoc for this struct
- augment Documentation/pinctrl.txt
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hongzhou Yang
Joachim Eastwood
Ray Jui
Andrew Bresticker
Geert Uytterhoeven
Ulrich Hecht
Mika Westerberg
Fabian Frederick
Krzysztof Kozlowski
Markus Pargmann
Helmut Buchsbaum
Linus Walleij
Sonic Zhang
Frank Li