We had a mix of formats used for specifying controller, bus, target,
and lun address of devices.
change to the format used by the scsi midlayer and upper layer (2:3:0:0)
so you can easily follow the information from hpsa to scsi midlayer
to sd upper layer.
Also add this information:
- product ID
- vendor ID
- RAID level
- SSD Smath Path capable and enabled
- exposure level (sg-only)
Example:
hpsa 0000:04:00.0: added scsi 2:0:0:0: Direct-Access HP LOGICAL VOLUME RAID-0 SSDSmartPathCap+ En+ Exp=4
scsi 2:0:0:0: Direct-Access HP LOGICAL VOLUME 10.0 PQ: 0 ANSI: 5
sd 2:0:0:0: [sdr] 12501713072 512-byte logical blocks: (6.40 TB/5.82 TiB)
sd 2:0:0:0: [sdr] 4096-byte physical blocks
sd 2:0:0:0: [sdr] Attached SCSI disk
sd 2:0:0:0: Attached scsi generic sg20 type 0
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Cache the ioaccel handle so that when we need to abort commands sent
down the ioaccel2 path, we can look up the LUN ID in h->dev[] instead of
having to do I/O to the controller.
Add a field to elements in h->dev[] to keep track of how the device is exposed
to the SCSI mid layer: Not at all, without an upper level driver
(no_uld_attach) or normally exposed.
Since masked physical devices are now present in h->dev[] array
it would be perfectly possible to do
echo scsi add-single-device 2 2 0 0 > /proc/scsi/scsi
and bring them online. This was previously not allowed for masked
physical devices.
Ensure that the mapping of physical disks to logical drives gets updated in a
consistent way when a RAID migration occurs and is not touched until updates
to it are complete.
now instead of doing CISS_REPORT_PHYSICAL to get the LUNID for
the physical disk in hpsa_get_pdisk_of_ioaccel2(), just get
it out of h->dev[] where we already have it cached.
do not touch phys_disk[] for ioaccel enabled logical drives during rescan
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@Suse.de>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The hpsa driver touches the hardware before checking the pci-id table.
This way, especially in kdump, it may confuse the proper driver (cciss).
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Don Brace <Don.Brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The driver has now been converted to DMA-API, so we should
increase the version number and remove the compilation
warning.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Only required if the dma buffer has been allocated via
dma_alloc_noncoherent(), which this one is not.
With that call removed we can now also compile on ARM.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
We should be using spin_lock_irqsave() when within the
interrupt handler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
DMA mapping might fail, so we need to check for errors here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
These definitions are only ever used for the wide-scsi board,
so they should be prefixed with 'ADV', not 'ASC'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Was uncommented in the original driver, and I'm too lazy to
figure out the conversion.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Removed unused structure ASC_SCSI_REQ_Q and update the
comments to 'ADV_SCSI_REQ_Q'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The 'data_addr' field is accessed by the board, and needs
to be kept in little endian format.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
AscIsrChipHalted will only ever return '0', so make it
a void function.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The sg elements should be allocated from a dma pool.
And rename the structure to 'adv_sg_block' as they
are only used by the wide board.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Webb Scales
Stephen Cameron
Tomas Henzl
Hannes Reinecke