If f_op->splice_write() is not implemented, fall back to a plain write.
Use vfs_writev() to write from the pipe buffers.
This will allow splice on all filesystems and file types. This
includes "direct_io" files in fuse which bypass the page cache.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If f_op->splice_read() is not implemented, fall back to a plain read.
Use vfs_readv() to read into previously allocated pages.
This will allow splice and functions using splice, such as the loop
device, to work on all filesystems. This includes "direct_io" files
in fuse which bypass the page cache.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Allow splice(2) to work when both the input and the output is a pipe.
Based on the impementation of the tee(2) syscall, but instead of
duplicating the buffer references move the buffers from the input pipe
to the output pipe.
Moving the whole buffer only succeeds if the full length of the buffer
is spliced. Otherwise duplicate the buffer, just like tee(2), set the
length of the output buffer and advance the offset on the input
buffer.
Since splice is operating on two pipes, special care needs to be taken
with locking to prevent AN ABBA deadlock. Again this is done
similarly to the tee(2) syscall, first preparing the input and output
pipes so there's data to consume and space for that data, and then
doing the move operation while holding both locks.
If other processes are doing I/O on the same pipes parallel to the
splice, then by the time both inodes are locked there might be no
buffers left to move, or no space to move them to. In this case retry
the whole operation, including the preparation phase. This could lead
to starvation, but I'm not sure if that's serious enough to worry
about.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Let's put the completion related functions back to block/blk-core.c
where they have lived. We can also unexport blk_end_bidi_request() and
__blk_end_bidi_request(), which nobody uses.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
blk_end_request_all() and __blk_end_request_all() should finish all
bytes including bidi, by definition. That's what all bidi users need ,
bidi requests must be complete as a whole (partial completion is
impossible).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Till now block layer allowed two separate modes of request execution.
A request is always acquired from the request queue via
elv_next_request(). After that, drivers are free to either dequeue it
or process it without dequeueing. Dequeue allows elv_next_request()
to return the next request so that multiple requests can be in flight.
Executing requests without dequeueing has its merits mostly in
allowing drivers for simpler devices which can't do sg to deal with
segments only without considering request boundary. However, the
benefit this brings is dubious and declining while the cost of the API
ambiguity is increasing. Segment based drivers are usually for very
old or limited devices and as converting to dequeueing model isn't
difficult, it doesn't justify the API overhead it puts on block layer
and its more modern users.
Previous patches converted all block low level drivers to dequeueing
model. This patch completes the API transition by...
* renaming elv_next_request() to blk_peek_request()
* renaming blkdev_dequeue_request() to blk_start_request()
* adding blk_fetch_request() which is combination of peek and start
* disallowing completion of queued (not started) requests
* applying new API to all LLDs
Renamings are for consistency and to break out of tree code so that
it's apparent that out of tree drivers need updating.
[ Impact: block request issue API cleanup, no functional change ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: unsik Kim <donari75@gmail.com>
Cc: Paul Clements <paul.clements@steeleye.com>
Cc: Tim Waugh <tim@cyberelk.net>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Laurent Vivier <Laurent@lvivier.info>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Stefan Weinhuber <wein@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
gdrom already dequeues and fully completes requests on normal path and
the error paths can be easily converted to do so too. Clean it up and
dequeue requests on error paths too.
While at it remove superflous blk_fs_request() && !blk_rq_sectors()
condition check.
[ Impact: dequeue in-flight request, cleanup ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
plat-omap/mailbox, floppy, viocd, mspro_block, i2o_block and
mmc/card/queue are already pretty close to dequeueing model and can be
converted with simple changes. Convert them.
While at it,
* xen-blkfront: !fs check moved downwards to share dequeue call with
normal path.
* mspro_block: __blk_end_request(..., blk_rq_cur_byte()) converted to
__blk_end_request_cur()
* mmc/card/queue: loop of __blk_end_request() converted to
__blk_end_request_all()
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
jsflash processes requests one-by-one synchronously from a kthread and
can be easily converted to dequeueing model. Convert it.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
mtd_blkdevs processes requests one-by-one synchronously from a kthread
and can be easily converted to dequeueing model. Convert it.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
xd processes requests one-by-one synchronously and can be easily
converted to dequeueing model. Convert it.
While at it, use rq_cur_bytes instead of rq_bytes when checking for
sector overflow. This is for for consistency and better behavior for
merged requests.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Request processing in amiflop is done sequentially in
redo_fd_request() proper and redo_fd_request() can easily be converted
to track in-flight request. Remove CURRENT, track in-flight request
directly and dequeue it when processing starts.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Other than in issue error paths, ps3disk always completely finishes
fetched requests. With full completion on error paths, it can be
easily converted to dequeueing model.
* After L1 r/w call failure, ps3disk_submit_request_sg() now fails the
whole request. Issue failure isn't likely to benefit from partial
retry anyway and ps3disk uses full failure in completion error path
too, so I don't think this amounts to any meaningful functionality
loss.
* flush completion is converted to _all for consistency. It doesn't
make any functional difference.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
pd/pf/pcd have track in-flight request by pd/pf/pcd_req. They can be
converted to dequeueing model by updating fetching and completion
paths. Convert them.
Note that removal of elv_next_request() call from pf_next_buf()
doesn't make any functional difference. The path is traveled only
during partial completion of a request and elv_next_request() call
must return the same request anyway.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Tim Waugh <tim@cyberelk.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
xsysace already tracks in-flight request using ace->req. Converting
to dequeueing model is mostly a matter of adding dequeueing call after
request fetching. The only tricky part is handling CF removal which
should complete both in flight and on queue requests. Convert to
dequeueing model.
While at it, remove explicit blk_rq_cur_bytes() and use
__blk_end_request_cur() instead.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
swim3 has at most single request in flight and already tracks it using
fd_req. Convert it to dequeuing model by updating request fetching
and wrapping completion function.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ataflop has single request in flight. Till now, whenever it needs to
access the in-flight request it called elv_next_request(). This patch
makes ataflop track the in-flight request directly and dequeue it when
processing starts. The added complexity is minimal and this will help
future block layer changes.
[ Impact: dequeue in-flight request, one elv_next_request() per request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
hd has at most single request in flight. Till now, whenever it needs
to access the in-flight request it called elv_next_request(). This
patch makes hd track the in-flight request directly and dequeue it
when processing starts. The added complexity is minimal and this will
help future block layer changes.
[ Impact: dequeue in-flight request, one elv_next_request() per request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
mg_disk has at most single request in flight per device. Till now,
whenever it needs to access the in-flight request it called
elv_next_request(). This patch makes mg_disk track the in-flight
request directly using mg_host->req and dequeue it when processing
starts.
q->queuedata is set to mg_host so that mg_host can be determined
without fetching request from the queue.
[ Impact: dequeue in-flight request, one elv_next_request() per request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: unsik Kim <donari75@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Both request functions in mg_disk simply return when they encounter a
!fs request, which means the request will never be cleared from the
queue causing queue hang and indefinite retry of the request. Fix it.
While at it, flatten condition checks and add unlikely to !fs tests.
[ Impact: fix possible queue hang / infinite retry of !fs requests ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: unsik Kim <donari75@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ide generally has single request in flight and tracks it using
hwif->rq and all state handlers follow the following convention.
* ide_started is returned if the request is in flight.
* ide_stopped is returned if the queue needs to be restarted. The
request might or might not have been processed fully or partially.
* hwif->rq is set to NULL, when an issued request completes.
So, dequeueing model can be implemented by dequeueing after fetch,
requeueing if hwif->rq isn't NULL on ide_stopped return and doing
about the same thing on completion / port unlock paths. These changes
can be made in ide-io proper.
In addition to the above main changes, the following updates are
necessary.
* ide-cd shouldn't dequeue a request when issuing REQUEST SENSE for it
as the request is already dequeued.
* ide-atapi uses request queue as stack when issuing REQUEST SENSE to
put the REQUEST SENSE in front of the failed request. This now
needs to be done using requeueing.
[ Impact: dequeue in-flight request ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Borislav Petkov <petkovbb@googlemail.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Miklos Szeredi
FUJITA Tomonori
Tejun Heo