If device has an owner, we shouldn't touch ubuf_info
since it might be in use.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another QMI speaking Qualcomm based device, which should be
driven by qmi_wwan, while cdc_ether should ignore it.
Like on other Huawei devices, the wwan function can appear
either as a single vendor specific interface or as a CDC ECM
class function using separate control and data interfaces.
The ECM control interface protocol is 0xff, likely in an
attempt to indicate that vendor specific management is
required.
In addition to the near standard CDC class, Huawei also add
vendor specific AT management commands to their firmwares.
This is probably an attempt to support non-Windows systems
using standard class drivers. Unfortunately, this part of
the firmware is often buggy. Linux is much better off using
whatever native vendor specific management protocol the
device offers, and Windows uses, whenever possible. This
means QMI in the case of Qualcomm based devices.
The E1820 has been verified to work fine with QMI.
Matching on interface number is necessary to distiguish the
wwan function from serial functions in the single interface
mode, as both function types will have class/subclass/function
set to ff/ff/ff.
The control interface number does not change in CDC ECM mode,
so the interface number matching rule is sufficient to handle
both modes. The cdc_ether blacklist entry is only relevant in
CDC ECM mode, but using a similar interface number based rule
helps document this as a transfer from one driver to another.
Other Huawei 02/06/ff devices are left with the cdc_ether driver
because we do not know whether they are based on Qualcomm chips.
The Huawei specific AT command management is known to be somewhat
hardware independent, and their usage of these class codes may
also be independent of the modem hardware.
Reported-by: Graham Inggs <graham.inggs@uct.ac.za>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the first loop in sh_eth_check_reset() runs to its end, 'cnt' is 0, so the
following check for 'cnt < 0' fails to catch the timeout. Fix the condition in
this check, so that the timeout is actually reported.
While at it, fix the grammar in the failure message...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
was playing with suspend and run into this:
|BUG: sleeping function called from invalid context at drivers/base/power/runtime.c:891
|in_atomic(): 1, irqs_disabled(): 0, pid: 1963, name: bash
|6 locks held by bash/1963:
|CPU: 0 PID: 1963 Comm: bash Not tainted 3.10.0-rc4+ #50
|[<c0014fdc>] (unwind_backtrace+0x0/0xf8) from [<c0011da4>] (show_stack+0x10/0x14)
|[<c0011da4>] (show_stack+0x10/0x14) from [<c02e8680>] (__pm_runtime_idle+0xa4/0xac)
|[<c02e8680>] (__pm_runtime_idle+0xa4/0xac) from [<c0341158>] (davinci_mdio_suspend+0x6c/0x9c)
|[<c0341158>] (davinci_mdio_suspend+0x6c/0x9c) from [<c02e0628>] (platform_pm_suspend+0x2c/0x54)
|[<c02e0628>] (platform_pm_suspend+0x2c/0x54) from [<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64)
|[<c02e52bc>] (dpm_run_callback.isra.3+0x2c/0x64) from [<c02e57e4>] (__device_suspend+0x100/0x22c)
|[<c02e57e4>] (__device_suspend+0x100/0x22c) from [<c02e67e8>] (dpm_suspend+0x68/0x230)
|[<c02e67e8>] (dpm_suspend+0x68/0x230) from [<c0072a20>] (suspend_devices_and_enter+0x68/0x350)
|[<c0072a20>] (suspend_devices_and_enter+0x68/0x350) from [<c0072f18>] (pm_suspend+0x210/0x24c)
|[<c0072f18>] (pm_suspend+0x210/0x24c) from [<c0071c74>] (state_store+0x6c/0xbc)
|[<c0071c74>] (state_store+0x6c/0xbc) from [<c02714dc>] (kobj_attr_store+0x14/0x20)
|[<c02714dc>] (kobj_attr_store+0x14/0x20) from [<c01341a0>] (sysfs_write_file+0x16c/0x19c)
|[<c01341a0>] (sysfs_write_file+0x16c/0x19c) from [<c00ddfe4>] (vfs_write+0xb4/0x190)
|[<c00ddfe4>] (vfs_write+0xb4/0x190) from [<c00de3a4>] (SyS_write+0x3c/0x70)
|[<c00de3a4>] (SyS_write+0x3c/0x70) from [<c000e2c0>] (ret_fast_syscall+0x0/0x48)
I don't see a reason why the pm_runtime call must be under the lock.
Further I don't understand why this is a spinlock and not mutex.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filters need to be translated to real BPF code for userland, like SO_GETFILTER.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Complier may generate codes that re-read the tun->numqueues during
tun_select_queue(). This may be a race if vlan->numqueues were changed in the
same time and can lead unexpected result (e.g. very huge value).
We need prevent the compiler from generating such codes by adding an
ACCESS_ONCE() to make sure tun->numqueues were only read once.
Bug were introduced by commit c8d68e6be1
(tuntap: multiqueue support).
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we decide not use zero-copy, msg.control should be set to NULL otherwise
macvtap/tap may set zerocopy callbacks which may decrease the kref of ubufs
wrongly.
Bug were introduced by commit cedb9bdce0
(vhost-net: skip head management if no outstanding).
This solves the following warnings:
WARNING: at include/linux/kref.h:47 handle_tx+0x477/0x4b0 [vhost_net]()
Modules linked in: vhost_net macvtap macvlan tun nfsd exportfs bridge stp llc openvswitch kvm_amd kvm bnx2 megaraid_sas [last unloaded: tun]
CPU: 5 PID: 8670 Comm: vhost-8668 Not tainted 3.10.0-rc2+ #1566
Hardware name: Dell Inc. PowerEdge R715/00XHKG, BIOS 1.5.2 04/19/2011
ffffffffa0198323 ffff88007c9ebd08 ffffffff81796b73 ffff88007c9ebd48
ffffffff8103d66b 000000007b773e20 ffff8800779f0000 ffff8800779f43f0
ffff8800779f8418 000000000000015c 0000000000000062 ffff88007c9ebd58
Call Trace:
[<ffffffff81796b73>] dump_stack+0x19/0x1e
[<ffffffff8103d66b>] warn_slowpath_common+0x6b/0xa0
[<ffffffff8103d6b5>] warn_slowpath_null+0x15/0x20
[<ffffffffa0197627>] handle_tx+0x477/0x4b0 [vhost_net]
[<ffffffffa0197690>] handle_tx_kick+0x10/0x20 [vhost_net]
[<ffffffffa019541e>] vhost_worker+0xfe/0x1a0 [vhost_net]
[<ffffffffa0195320>] ? vhost_attach_cgroups_work+0x30/0x30 [vhost_net]
[<ffffffffa0195320>] ? vhost_attach_cgroups_work+0x30/0x30 [vhost_net]
[<ffffffff81061f46>] kthread+0xc6/0xd0
[<ffffffff81061e80>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff817a1aec>] ret_from_fork+0x7c/0xb0
[<ffffffff81061e80>] ? kthread_freezable_should_stop+0x70/0x70
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
The following patchset contains four fixes for Netfilter and one fix
for IPVS, they are:
* Fix data leak to user-space via getsockopt IP_VS_SO_GET_DESTS, from
Dan Carpenter.
* Fix xt_TCPMSS if no TCP MSS is specified in syn packets, to avoid the
violation of RFC879, from Phil Oester.
* Fix incomplete dump of objects via nfnetlink_acct and nfnetlink_cttimeout,
from myself.
* Fix missing HW protocol in packets passed to user-space via NFQUEUE,
from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The entry struct has a 2 byte hole after ->port and another 4 byte
hole after ->stats.outpkts. You must have CAP_NET_ADMIN in your
namespace to hit this information leak.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
qdisc_get_rtab() should check not only the keys in struct tc_ratespec,
but also the full data[] array.
"tc ... linklayer atm " only perturbs values in the 256 slots array.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fix from David Miller:
"This is a quick one commit pull request to cure the regression
introduced by the MSG_CMSG_COMPAT change."
(Background: commit 1be374a051 completely broke 32-bit COMPAT handling
by not only disallowing MSG_CMSG_COMPAT from user APIs, but clearing it
in our own internal use too!)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Unbreak compat_sys_{send,recv}msg
Pull staging driver fixes from Greg Kroah-Hartman:
"Here are some staging and IIO driver fixes for the 3.10-rc5 release.
All of them are tiny, and fix a number of reported issues (build and
runtime)"
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'staging-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio:inkern: Fix typo/bug in convert raw to processed.
iio: frequency: ad4350: Fix bug / typo in mask
inkern: iio_device_put after incorrect return/goto
staging: alarm-dev: information leak in alarm_compat_ioctl()
iio:callback buffer: free the scan_mask
staging: alarm-dev: information leak in alarm_ioctl()
drivers: staging: zcache: fix compile error
staging: dwc2: fix value of dma_mask
Pull tty/serial driver fixes from Greg Kroah-Hartman:
"Here are some small bugfixes, and one revert, of serial driver issues
that have been reported"
* tag 'tty-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: Make SERIAL_8250_RUNTIME_UARTS work correctly"
serial: samsung: enable clock before clearing pending interrupts during init
serial/imx: disable hardware flow control at startup
Pull USB fixes from Greg Kroah-Hartman:
"Here are a number of USB bugfixes and new device ids for the 3.10-rc5
tree.
Nothing major here, a number of new device ids (and movement from the
option to the zte_ev driver of a number of ids that we had previously
gotten wrong, some xhci bugfixes, some usb-serial driver fixes that
were recently found, some host controller fixes / reverts, and a
variety of smaller other things"
* tag 'usb-3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (29 commits)
USB: option,zte_ev: move most ZTE CDMA devices to zte_ev
USB: option: blacklist network interface on Huawei E1820
USB: whiteheat: fix broken port configuration
USB: serial: fix TIOCMIWAIT return value
USB: mos7720: fix hardware flow control
USB: keyspan: remove unused endpoint-array access
USB: keyspan: fix bogus array index
USB: zte_ev: fix broken open
USB: serial: Add Option GTM681W to qcserial device table.
USB: Serial: cypress_M8: Enable FRWD Dongle hidcom device
USB: EHCI: fix regression related to qh_refresh()
usbfs: Increase arbitrary limit for USB 3 isopkt length
USB: zte_ev: fix control-message timeouts
USB: mos7720: fix message timeouts
USB: iuu_phoenix: fix bulk-message timeout
USB: ark3116: fix control-message timeout
USB: mos7840: fix DMA to stack
USB: mos7720: fix DMA to stack
USB: visor: fix initialisation of Treo/Kyocera devices
USB: serial: fix Treo/Kyocera interrrupt-in urb context
...
Pull PCI fixes from Bjorn Helgaas:
"This fixes a crash when booting a 32-bit kernel via the EFI boot stub.
PCI ROM from EFI
x86/PCI: Map PCI setup data with ioremap() so it can be in highmem"
* tag 'pci-v3.10-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
x86/PCI: Map PCI setup data with ioremap() so it can be in highmem
Pull more xfs updates from Ben Myers:
"Here are several fixes for filesystems with CRC support turned on:
fixes for quota, remote attributes, and recovery. There is also some
feature work related to CRCs: the implementation of CRCs for the inode
unlinked lists, disabling noattr2/attr2 options when appropriate, and
bumping the maximum number of ACLs.
I would have preferred to defer this last category of items to 3.11.
This would require setting a feature bit for the on-disk changes, so
there is some pressure to get these in 3.10. I believe this
represents the end of the CRC related queue.
- Rework of dquot CRCs
- Fix for remote attribute invalidation of a leaf
- Fix ordering of transaction replay in recovery
- Implement CRCs for inode unlinked list
- Disable noattr2/attr2 mount options when CRCs are enabled
- Bump the limitation of ACL entries for v5 superblocks"
* tag 'for-linus-v3.10-rc5' of git://oss.sgi.com/xfs/xfs:
xfs: increase number of ACL entries for V5 superblocks
xfs: disable noattr2/attr2 mount options for CRC enabled filesystems
xfs: inode unlinked list needs to recalculate the inode CRC
xfs: fix log recovery transaction item reordering
xfs: fix remote attribute invalidation for a leaf
xfs: rework dquot CRCs
I broke them in this commit:
commit 1be374a051
Author: Andy Lutomirski <luto@amacapital.net>
Date: Wed May 22 14:07:44 2013 -0700
net: Block MSG_CMSG_COMPAT in send(m)msg and recv(m)msg
This patch adds __sys_sendmsg and __sys_sendmsg as common helpers that accept
MSG_CMSG_COMPAT and blocks MSG_CMSG_COMPAT at the syscall entrypoints. It
also reverts some unnecessary checks in sys_socketcall.
Apparently I was suffering from underscore blindness the first time around.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per some ZTE Linux drivers I found for the AC2716, the following patch
moves most ZTE CDMA devices from option to zte_ev. The blacklist stuff
that option does is not required with zte_ev, because it doesn't
implement any of the send_setup hooks which the blacklist suppressed.
I did not move the 2718 over because I could not find any ZTE Linux
drivers for that device, nor even any Windows drivers.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When configuring the port (e.g. set_termios) the port minor number
rather than the port number was used in the request (and they only
coincide for minor number 0).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The limit of 25 ACL entries is arbitrary, but baked into the on-disk
format. For version 5 superblocks, increase it to the maximum nuber
of ACLs that can fit into a single xattr.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Mark Tinguely <tinuguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 5c87d4bc1a)
attr2 format is always enabled for v5 superblock filesystems, so the
mount options to enable or disable it need to be cause mount errors.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit d3eaace84e)
The inode unlinked list manipulations operate directly on the inode
buffer, and so bypass the inode CRC calculation mechanisms. Hence an
inode on the unlinked list has an invalid CRC. Fix this by
recalculating the CRC whenever we modify an unlinked list pointer in
an inode, ncluding during log recovery. This is trivial to do and
results in unlinked list operations always leaving a consistent
inode in the buffer.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit 0a32c26e72)
There are several constraints that inode allocation and unlink
logging impose on log recovery. These all stem from the fact that
inode alloc/unlink are logged in buffers, but all other inode
changes are logged in inode items. Hence there are ordering
constraints that recovery must follow to ensure the correct result
occurs.
As it turns out, this ordering has been working mostly by chance
than good management. The existing code moves all buffers except
cancelled buffers to the head of the list, and everything else to
the tail of the list. The problem with this is that is interleaves
inode items with the buffer cancellation items, and hence whether
the inode item in an cancelled buffer gets replayed is essentially
left to chance.
Further, this ordering causes problems for log recovery when inode
CRCs are enabled. It typically replays the inode unlink buffer long before
it replays the inode core changes, and so the CRC recorded in an
unlink buffer is going to be invalid and hence any attempt to
validate the inode in the buffer is going to fail. Hence we really
need to enforce the ordering that the inode alloc/unlink code has
expected log recovery to have since inode chunk de-allocation was
introduced back in 2003...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
(cherry picked from commit a775ad7780)
Michael S. Tsirkin
Bjørn Mork
Sergei Shtylyov
Sebastian Siewior
Nicolas Dichtel
Jason Wang
David S. Miller
Dan Carpenter
Eric Dumazet
Pablo Neira Ayuso
Linus Torvalds
Andy Lutomirski
Dan Williams
Johan Hovold
Dave Chinner