In reshape cases that do not change the number of devices,
start_reshape is called without first calling check_reshape.
Currently, the check that the stripe_cache is large enough is
only done in check_reshape. It should be in start_reshape too.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ Raid5 has learned to take over also raid4 and raid6 arrays.
2/ new_chunk in mdp_superblock_1 is in sectors, not bytes.
Signed-off-by: NeilBrown <neilb@suse.de>
A straight-forward conversion which gets rid of some
multiplications/divisions/shifts. The patch also introduces a couple
of new ones, most of which are due to conf->chunk_size still being
represented in bytes. This will be cleaned up in subsequent patches.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch renames the chunk_size field to chunk_sectors with the
implied change of semantics. Since
is_power_of_2(chunk_size) = is_power_of_2(chunk_sectors << 9)
= is_power_of_2(chunk_sectors)
these bits don't need an adjustment for the shift.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Maintain two flows, one for pow2 chunk sizes (which uses masks and
shift), and a flow for the general case (which uses sector_div).
This is for the sake of performance.
- introduce map_sector and is_io_in_chunk_boundary to encapsulate
those two flows better for raid0_make_request
- fix blk_mergeable to support the two flows.
Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>
Remove chunk size check from md as this is now performed in the run
function in each personality.
Replace chunk size power 2 code calculations by a regular division.
Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>
have raid0 check chunk size in run method instead of in md.
This is part of a series moving the checks from common code to
the personalities where they belong.
hardsect is short and chunksize is an int, so it is safe to use %.
Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>
Replace the linear search with binary search in which_dev.
Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Remove num_sectors from dev_info and replace start_sector with
end_sector. This makes a lot of comparisons much simpler.
Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Get rid of sector_div and hash table for linear raid and replace
with a linear search in which_dev.
The hash table adds a lot of complexity for little if any gain.
Ultimately a binary search will be used which will have smaller
cache foot print, a similar number of memory access, and no
divisions.
Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.
So open code the macro everywhere and remove the pointless cast.
Signed-off-by: NeilBrown <neilb@suse.de>
This setting doesn't seem to make sense (half the chunk size??) and
shouldn't be needed.
The segment boundary exported by raid0 should simply be the minimum
of the segment boundary of all component devices. And we already
get that right.
Signed-off-by: NeilBrown <neilb@suse.de>
If we treat conf->devlist more like a 2 dimensional array,
we can get the devlist for a particular zone simply by indexing
that array, so we don't need to store the pointers to subarrays
in strip_zone. This makes strip_zone smaller and so (hopefully)
searches faster.
Signed-of-by: NeilBrown <neilb@suse.de>
storing ->sectors is redundant as is can be computed from the
difference z->zone_end - (z-1)->zone_end
The one place where it is used, it is just as efficient to use
a zone_end value instead.
And removing it makes strip_zone smaller, so they array of these that
is searched on every request has a better chance to say in cache.
So discard the field and get the value from elsewhere.
Signed-off-by: NeilBrown <neilb@suse.de>
raid0_stop() removes all references to the raid0 configuration but
misses to free the ->devlist buffer.
This patch closes this leak, removes a pointless initialization and
fixes a coding style issue in raid0_stop().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently the raid0 configuration is allocated in raid0_run() while
the buffers for the strip_zone and the dev_list arrays are allocated
in create_strip_zones(). On errors, all three buffers are freed
in raid0_run().
It's easier and more readable to do the allocation and cleanup within
a single function. So move that code into create_strip_zones().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently raid0_run() always returns -ENOMEM on errors. This is
incorrect as running the array might fail for other reasons, for
example because not all component devices were available.
This patch changes create_strip_zones() so that it returns a proper
error code (either -ENOMEM or -EINVAL) rather than 1 on errors and
makes raid0_run(), its single caller, return that value instead
of -ENOMEM.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
The "sector_shift" and "spacing" fields of struct raid0_private_data
were only used for the hash table lookups. So the removal of the
hash table allows get rid of these fields as well which simplifies
create_strip_zones() and raid0_run() quite a bit.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown
Andre Noll
raz ben yehuda
Sandeep K Sinha