Merge branch 'perf/urgent' into perf/core, to resolve conflict

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt

@@ -1,13 +1,16 @@
 == Amlogic Meson pinmux controller ==
 
 Required properties for the root node:
- - compatible: "amlogic,meson8-pinctrl" or "amlogic,meson8b-pinctrl"
+ - compatible: one of "amlogic,meson8-cbus-pinctrl"
+		      "amlogic,meson8b-cbus-pinctrl"
+		      "amlogic,meson8-aobus-pinctrl"
+		      "amlogic,meson8b-aobus-pinctrl"
  - reg: address and size of registers controlling irq functionality
 
 === GPIO sub-nodes ===
 
-The 2 power domains of the controller (regular and always-on) are
-represented as sub-nodes and each of them acts as a GPIO controller.
+The GPIO bank for the controller is represented as a sub-node and it acts as a
+GPIO controller.
 
 Required properties for sub-nodes are:
  - reg: should contain address and size for mux, pull-enable, pull and
@@ -18,10 +21,6 @@ Required properties for sub-nodes are:
  - gpio-controller: identifies the node as a gpio controller
  - #gpio-cells: must be 2
 
-Valid sub-node names are:
- - "banks" for the regular domain
- - "ao-bank" for the always-on domain
-
 === Other sub-nodes ===
 
 Child nodes without the "gpio-controller" represent some desired
@@ -45,7 +44,7 @@ pinctrl-bindings.txt
 === Example ===
 
 	pinctrl: pinctrl@c1109880 {
-		compatible = "amlogic,meson8-pinctrl";
+		compatible = "amlogic,meson8-cbus-pinctrl";
 		reg = <0xc1109880 0x10>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -61,15 +60,6 @@ pinctrl-bindings.txt
 			#gpio-cells = <2>;
                };
 
-		gpio_ao: ao-bank@c1108030 {
-			reg = <0xc8100014 0x4>,
-			      <0xc810002c 0x4>,
-			      <0xc8100024 0x8>;
-			reg-names = "mux", "pull", "gpio";
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
 		nand {
 			mux {
 				groups = "nand_io", "nand_io_ce0", "nand_io_ce1",
@@ -79,18 +69,4 @@ pinctrl-bindings.txt
 				function = "nand";
 			};
 		};
-
-		uart_ao_a {
-			mux {
-				groups = "uart_tx_ao_a", "uart_rx_ao_a",
-					 "uart_cts_ao_a", "uart_rts_ao_a";
-				function = "uart_ao";
-			};
-
-			conf {
-				pins = "GPIOAO_0", "GPIOAO_1",
-				       "GPIOAO_2", "GPIOAO_3";
-				bias-disable;
-			};
-		};
 	};

Documentation/kernel-parameters.txt

@@ -4077,6 +4077,8 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
 					sector if the number is odd);
 				i = IGNORE_DEVICE (don't bind to this
 					device);
+				j = NO_REPORT_LUNS (don't use report luns
+					command, uas only);
 				l = NOT_LOCKABLE (don't try to lock and
 					unlock ejectable media);
 				m = MAX_SECTORS_64 (don't transfer more

Documentation/usb/gadget_multi.txt

@@ -43,7 +43,7 @@ For the gadget two work under Windows two conditions have to be met:
 First of all, Windows need to detect the gadget as an USB composite
 gadget which on its own have some conditions[4].  If they are met,
 Windows lets USB Generic Parent Driver[5] handle the device which then
-tries to much drivers for each individual interface (sort of, don't
+tries to match drivers for each individual interface (sort of, don't
 get into too many details).
 
 The good news is: you do not have to worry about most of the

Documentation/x86/protection-keys.txt

@@ -0,0 +1,27 @@
+Memory Protection Keys for Userspace (PKU aka PKEYs) is a CPU feature
+which will be found on future Intel CPUs.
+
+Memory Protection Keys provides a mechanism for enforcing page-based
+protections, but without requiring modification of the page tables
+when an application changes protection domains.  It works by
+dedicating 4 previously ignored bits in each page table entry to a
+"protection key", giving 16 possible keys.
+
+There is also a new user-accessible register (PKRU) with two separate
+bits (Access Disable and Write Disable) for each key.  Being a CPU
+register, PKRU is inherently thread-local, potentially giving each
+thread a different set of protections from every other thread.
+
+There are two new instructions (RDPKRU/WRPKRU) for reading and writing
+to the new register.  The feature is only available in 64-bit mode,
+even though there is theoretically space in the PAE PTEs.  These
+permissions are enforced on data access only and have no effect on
+instruction fetches.
+
+=========================== Config Option ===========================
+
+This config option adds approximately 1.5kb of text. and 50 bytes of
+data to the executable.  A workload which does large O_DIRECT reads
+of holes in XFS files was run to exercise get_user_pages_fast().  No
+performance delta was observed with the config option
+enabled or disabled.

MAINTAINERS

@@ -6252,8 +6252,8 @@ S:	Maintained
 F:	tools/testing/selftests
 
 KERNEL VIRTUAL MACHINE (KVM)
-M:	Gleb Natapov <gleb@kernel.org>
 M:	Paolo Bonzini <pbonzini@redhat.com>
+M:	Radim Krčmář <rkrcmar@redhat.com>
 L:	kvm@vger.kernel.org
 W:	http://www.linux-kvm.org
 T:	git git://git.kernel.org/pub/scm/virt/kvm/kvm.git

Makefile

@@ -1,7 +1,7 @@
 VERSION = 4
 PATCHLEVEL = 6
 SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc4
 NAME = Blurry Fish Butt
 
 # *DOCUMENTATION*

arch/arc/Kconfig

@@ -593,7 +593,6 @@ config PCI_SYSCALL
 	def_bool PCI
 
 source "drivers/pci/Kconfig"
-source "drivers/pci/pcie/Kconfig"
 
 endmenu
 

arch/arc/boot/dts/axs10x_mb.dtsi

@@ -47,14 +47,6 @@
 			clocks = <&apbclk>;
 			clock-names = "stmmaceth";
 			max-speed = <100>;
-			mdio0 {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				compatible = "snps,dwmac-mdio";
-				phy1: ethernet-phy@1 {
-					reg = <1>;
-				};
-			};
 		};
 
 		ehci@0x40000 {

arch/arc/configs/axs103_defconfig

@@ -42,6 +42,7 @@ CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_BLK_DEV_LOOP=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_NETDEVICES=y

arch/arc/configs/axs103_smp_defconfig

@@ -43,6 +43,7 @@ CONFIG_DEVTMPFS=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 # CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_BLK_DEV_LOOP=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_NETDEVICES=y

arch/arc/include/asm/fb.h

@@ -0,0 +1,19 @@
+#ifndef _ASM_FB_H_
+#define _ASM_FB_H_
+
+#include <linux/fb.h>
+#include <linux/fs.h>
+#include <asm/page.h>
+
+static inline void fb_pgprotect(struct file *file, struct vm_area_struct *vma,
+				unsigned long off)
+{
+	vma->vm_page_prot = pgprot_noncached(vma->vm_page_prot);
+}
+
+static inline int fb_is_primary_device(struct fb_info *info)
+{
+	return 0;
+}
+
+#endif /* _ASM_FB_H_ */

arch/arm/boot/dts/am335x-baltos-ir5221.dts

@@ -470,9 +470,12 @@
 };
 
 &cpsw_emac0 {
-	phy_id = <&davinci_mdio>, <0>;
 	phy-mode = "rmii";
 	dual_emac_res_vlan = <1>;
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
 };
 
 &cpsw_emac1 {

arch/arm/boot/dts/am4372.dtsi

@@ -207,7 +207,7 @@
 			ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 5>,
 				   <&edma_tptc2 0>;
 
-			ti,edma-memcpy-channels = <32 33>;
+			ti,edma-memcpy-channels = <58 59>;
 		};
 
 		edma_tptc0: tptc@49800000 {

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -794,3 +794,8 @@
 	tx-num-evt = <32>;
 	rx-num-evt = <32>;
 };
+
+&synctimer_32kclk {
+	assigned-clocks = <&mux_synctimer32k_ck>;
+	assigned-clock-parents = <&clkdiv32k_ick>;
+};

arch/arm/boot/dts/armada-385-linksys.dtsi

@@ -117,7 +117,7 @@
 			};
 
 			/* USB part of the eSATA/USB 2.0 port */
-			usb@50000 {
+			usb@58000 {
 				status = "okay";
 			};
 

arch/arm/boot/dts/meson8.dtsi

@@ -91,8 +91,8 @@
 		clock-frequency = <141666666>;
 	};
 
-	pinctrl: pinctrl@c1109880 {
-		compatible = "amlogic,meson8-pinctrl";
+	pinctrl_cbus: pinctrl@c1109880 {
+		compatible = "amlogic,meson8-cbus-pinctrl";
 		reg = <0xc1109880 0x10>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -108,29 +108,6 @@
 			#gpio-cells = <2>;
 		};
 
-		gpio_ao: ao-bank@c1108030 {
-			reg = <0xc8100014 0x4>,
-			      <0xc810002c 0x4>,
-			      <0xc8100024 0x8>;
-			reg-names = "mux", "pull", "gpio";
-			gpio-controller;
-			#gpio-cells = <2>;
-		};
-
-		uart_ao_a_pins: uart_ao_a {
-			mux {
-				groups = "uart_tx_ao_a", "uart_rx_ao_a";
-				function = "uart_ao";
-			};
-		};
-
-		i2c_ao_pins: i2c_mst_ao {
-			mux {
-				groups = "i2c_mst_sck_ao", "i2c_mst_sda_ao";
-				function = "i2c_mst_ao";
-			};
-		};
-
 		spi_nor_pins: nor {
 			mux {
 				groups = "nor_d", "nor_q", "nor_c", "nor_cs";
@@ -157,4 +134,34 @@
 		};
 	};
 
+	pinctrl_aobus: pinctrl@c8100084 {
+		compatible = "amlogic,meson8-aobus-pinctrl";
+		reg = <0xc8100084 0xc>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio_ao: ao-bank@c1108030 {
+			reg = <0xc8100014 0x4>,
+			      <0xc810002c 0x4>,
+			      <0xc8100024 0x8>;
+			reg-names = "mux", "pull", "gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		uart_ao_a_pins: uart_ao_a {
+			mux {
+				groups = "uart_tx_ao_a", "uart_rx_ao_a";
+				function = "uart_ao";
+			};
+		};
+
+		i2c_ao_pins: i2c_mst_ao {
+			mux {
+				groups = "i2c_mst_sck_ao", "i2c_mst_sda_ao";
+				function = "i2c_mst_ao";
+			};
+		};
+	};
 }; /* end of / */

arch/arm/boot/dts/meson8b.dtsi

@@ -155,8 +155,8 @@
 			reg = <0xc1108000 0x4>, <0xc1104000 0x460>;
 		};
 
-		pinctrl: pinctrl@c1109880 {
-			compatible = "amlogic,meson8b-pinctrl";
+		pinctrl_cbus: pinctrl@c1109880 {
+			compatible = "amlogic,meson8b-cbus-pinctrl";
 			reg = <0xc1109880 0x10>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -171,6 +171,14 @@
 				gpio-controller;
 				#gpio-cells = <2>;
 			};
+		};
+
+		pinctrl_aobus: pinctrl@c8100084 {
+			compatible = "amlogic,meson8b-aobus-pinctrl";
+			reg = <0xc8100084 0xc>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
 
 			gpio_ao: ao-bank@c1108030 {
 				reg = <0xc8100014 0x4>,

arch/arm/boot/dts/omap4.dtsi

@@ -70,7 +70,7 @@
 		compatible = "arm,cortex-a9-twd-timer";
 		clocks = <&mpu_periphclk>;
 		reg = <0x48240600 0x20>;
-		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_EDGE_RISING)>;
 		interrupt-parent = <&gic>;
 	};
 

arch/arm/configs/u8500_defconfig

@@ -63,6 +63,9 @@ CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_BU21013=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_AB8500_PONKEY=y
+CONFIG_RMI4_CORE=y
+CONFIG_RMI4_I2C=y
+CONFIG_RMI4_F11=y
 # CONFIG_SERIO is not set
 CONFIG_VT_HW_CONSOLE_BINDING=y
 # CONFIG_LEGACY_PTYS is not set

arch/arm/kvm/arm.c

@@ -1112,10 +1112,17 @@ static void __init hyp_cpu_pm_init(void)
 {
 	cpu_pm_register_notifier(&hyp_init_cpu_pm_nb);
 }
+static void __init hyp_cpu_pm_exit(void)
+{
+	cpu_pm_unregister_notifier(&hyp_init_cpu_pm_nb);
+}
 #else
 static inline void hyp_cpu_pm_init(void)
 {
 }
+static inline void hyp_cpu_pm_exit(void)
+{
+}
 #endif
 
 static void teardown_common_resources(void)
@@ -1141,9 +1148,7 @@ static int init_subsystems(void)
 	/*
 	 * Register CPU Hotplug notifier
 	 */
-	cpu_notifier_register_begin();
-	err = __register_cpu_notifier(&hyp_init_cpu_nb);
-	cpu_notifier_register_done();
+	err = register_cpu_notifier(&hyp_init_cpu_nb);
 	if (err) {
 		kvm_err("Cannot register KVM init CPU notifier (%d)\n", err);
 		return err;
@@ -1193,6 +1198,8 @@ static void teardown_hyp_mode(void)
 	free_hyp_pgds();
 	for_each_possible_cpu(cpu)
 		free_page(per_cpu(kvm_arm_hyp_stack_page, cpu));
+	unregister_cpu_notifier(&hyp_init_cpu_nb);
+	hyp_cpu_pm_exit();
 }
 
 static int init_vhe_mode(void)