Merge tag 'asoc-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next

ASoC: Updates for v3.7 Lots and lots of driver specific cleanups and enhancements but the only substantial framework feature this time round is the compressed API binding: - Addition of ASoC bindings for the compressed API, used by the mid-x86 drivers. - Lots of cleanups and API refreshes for CODEC drivers and DaVinci. - Conversion of OMAP to dmaengine. - New machine driver for Wolfson Microelectronics Bells. - New CODEC driver for Wolfson Microelectronics WM0010.
2026-05-01 15:00:59 -07:00 · 2012-09-22 18:31:08 +02:00
parent 99df18b31d ddfb43f388
commit 3d98c21d06
726 changed files with 10137 additions and 5455 deletions
@@ -210,3 +210,15 @@ Users:
 		firmware assigned instance number of the PCI
 		device that can help in understanding the firmware
 		intended order of the PCI device.
+
+What:		/sys/bus/pci/devices/.../d3cold_allowed
+Date:		July 2012
+Contact:	Huang Ying <ying.huang@intel.com>
+Description:
+		d3cold_allowed is bit to control whether the corresponding PCI
+		device can be put into D3Cold state.  If it is cleared, the
+		device will never be put into D3Cold state.  If it is set, the
+		device may be put into D3Cold state if other requirements are
+		satisfied too.  Reading this attribute will show the current
+		value of d3cold_allowed bit.  Writing this attribute will set
+		the value of d3cold_allowed bit.
@@ -0,0 +1,46 @@
+Texas Instruments TWL family (twl4030) audio module
+
+The audio module inside the TWL family consist of an audio codec and a vibra
+driver.
+
+Required properties:
+- compatible : must be "ti,twl4030-audio"
+
+Optional properties, nodes:
+
+Audio functionality:
+- codec { }: Need to be present if the audio functionality is used. Within this
+	     section the following options can be used:
+- ti,digimic_delay: Delay need after enabling the digimic to reduce artifacts
+		    from the start of the recorded sample (in ms)
+-ti,ramp_delay_value: HS ramp delay configuration to reduce pop noise
+-ti,hs_extmute: Use external mute for HS pop reduction
+-ti,hs_extmute_gpio: Use external GPIO to control the external mute
+-ti,offset_cncl_path: Offset cancellation path selection, refer to TRM for the
+		      valid values.
+
+Vibra functionality
+- ti,enable-vibra: Need to be set to <1> if the vibra functionality is used. if
+		   missing or it is 0, the vibra functionality is disabled.
+
+Example:
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+
+		twl_audio: audio {
+			compatible = "ti,twl4030-audio";
+
+			ti,enable-vibra = <1>;
+
+			codec {
+				ti,ramp_delay_value = <3>;
+			};
+
+		};
+	};
+};
@@ -0,0 +1,21 @@
+CS4270 audio CODEC
+
+The driver for this device currently only supports I2C.
+
+Required properties:
+
+  - compatible : "cirrus,cs4270"
+
+  - reg : the I2C address of the device for I2C
+
+Optional properties:
+
+  - reset-gpio : a GPIO spec for the reset pin. If specified, it will be
+		 deasserted before communication to the codec starts.
+
+Example:
+
+codec: cs4270@48 {
+	compatible = "cirrus,cs4270";
+	reg = <0x48>;
+};
@@ -0,0 +1,45 @@
+Texas Instruments McASP controller
+
+Required properties:
+- compatible :
+	"ti,dm646x-mcasp-audio"	: for DM646x platforms
+	"ti,da830-mcasp-audio"	: for both DA830 & DA850 platforms
+	"ti,omap2-mcasp-audio"	: for OMAP2 platforms (TI81xx, AM33xx)
+
+- reg : Should contain McASP registers offset and length
+- interrupts : Interrupt number for McASP
+- op-mode : I2S/DIT ops mode.
+- tdm-slots : Slots for TDM operation.
+- num-serializer : Serializers used by McASP.
+- serial-dir : A list of serializer pin mode. The list number should be equal
+		to "num-serializer" parameter. Each entry is a number indication
+		serializer pin direction. (0 - INACTIVE, 1 - TX, 2 - RX)
+
+
+Optional properties:
+
+- ti,hwmods : Must be "mcasp<n>", n is controller instance starting 0
+- tx-num-evt : FIFO levels.
+- rx-num-evt : FIFO levels.
+- sram-size-playback : size of sram to be allocated during playback
+- sram-size-capture  : size of sram to be allocated during capture
+
+Example:
+
+mcasp0: mcasp0@1d00000 {
+	compatible = "ti,da830-mcasp-audio";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	reg = <0x100000 0x3000>;
+	interrupts = <82 83>;
+	op-mode = <0>;		/* MCASP_IIS_MODE */
+	tdm-slots = <2>;
+	num-serializer = <16>;
+	serial-dir = <
+			0 0 0 0	/* 0: INACTIVE, 1: TX, 2: RX */
+			0 0 0 0
+			0 0 0 1
+			2 0 0 0 >;
+	tx-num-evt = <1>;
+	rx-num-evt = <1>;
+};
@@ -0,0 +1,91 @@
+* Texas Instruments OMAP4+ and twl6040 based audio setups
+
+Required properties:
+- compatible: "ti,abe-twl6040"
+- ti,model: Name of the sound card ( for example "SDP4430")
+- ti,mclk-freq: MCLK frequency for HPPLL operation
+- ti,mcpdm: phandle for the McPDM node
+- ti,twl6040: phandle for the twl6040 core node
+- ti,audio-routing: List of connections between audio components.
+  Each entry is a pair of strings, the first being the connection's sink,
+  the second being the connection's source.
+
+Optional properties:
+- ti,dmic: phandle for the OMAP dmic node if the machine have it connected
+- ti,jack_detection: Need to be set to <1> if the board capable to detect jack
+  insertion, removal.
+
+Available audio endpoints for the audio-routing table:
+
+Board connectors:
+ * Headset Stereophone
+ * Earphone Spk
+ * Ext Spk
+ * Line Out
+ * Vibrator
+ * Headset Mic
+ * Main Handset Mic
+ * Sub Handset Mic
+ * Line In
+ * Digital Mic
+
+twl6040 pins:
+ * HSOL
+ * HSOR
+ * EP
+ * HFL
+ * HFR
+ * AUXL
+ * AUXR
+ * VIBRAL
+ * VIBRAR
+ * HSMIC
+ * MAINMIC
+ * SUBMIC
+ * AFML
+ * AFMR
+
+ * Headset Mic Bias
+ * Main Mic Bias
+ * Digital Mic1 Bias
+ * Digital Mic2 Bias
+
+Digital mic pins:
+ * DMic
+
+Example:
+
+sound {
+	compatible = "ti,abe-twl6040";
+	ti,model = "SDP4430";
+
+	ti,jack-detection = <1>;
+	ti,mclk-freq = <38400000>;
+
+	ti,mcpdm = <&mcpdm>;
+	ti,dmic = <&dmic>;
+
+	ti,twl6040 = <&twl6040>;
+
+	/* Audio routing */
+	ti,audio-routing =
+		"Headset Stereophone", "HSOL",
+		"Headset Stereophone", "HSOR",
+		"Earphone Spk", "EP",
+		"Ext Spk", "HFL",
+		"Ext Spk", "HFR",
+		"Line Out", "AUXL",
+		"Line Out", "AUXR",
+		"Vibrator", "VIBRAL",
+		"Vibrator", "VIBRAR",
+		"HSMIC", "Headset Mic",
+		"Headset Mic", "Headset Mic Bias",
+		"MAINMIC", "Main Handset Mic",
+		"Main Handset Mic", "Main Mic Bias",
+		"SUBMIC", "Sub Handset Mic",
+		"Sub Handset Mic", "Main Mic Bias",
+		"AFML", "Line In",
+		"AFMR", "Line In",
+		"DMic", "Digital Mic",
+		"Digital Mic", "Digital Mic1 Bias";
+};
@@ -0,0 +1,37 @@
+* Texas Instruments OMAP2+ McBSP module
+
+Required properties:
+- compatible: "ti,omap2420-mcbsp" for McBSP on OMAP2420
+	      "ti,omap2430-mcbsp" for McBSP on OMAP2430
+	      "ti,omap3-mcbsp" for McBSP on OMAP3
+	      "ti,omap4-mcbsp" for McBSP on OMAP4 and newer SoC
+- reg: Register location and size, for OMAP4+ as an array:
+       <MPU access base address, size>,
+       <L3 interconnect address, size>;
+- reg-names: Array of strings associated with the address space
+- interrupts: Interrupt numbers for the McBSP port, as an array in case the
+	      McBSP IP have more interrupt lines:
+	<OCP compliant irq>,
+	<TX irq>,
+	<RX irq>;
+- interrupt-names: Array of strings associated with the interrupt numbers
+- interrupt-parent: The parent interrupt controller
+- ti,buffer-size: Size of the FIFO on the port (OMAP2430 and newer SoC)
+- ti,hwmods: Name of the hwmod associated to the McBSP port
+
+Example:
+
+mcbsp2: mcbsp@49022000 {
+	compatible = "ti,omap3-mcbsp";
+	reg = <0x49022000 0xff>,
+	      <0x49028000 0xff>;
+	reg-names = "mpu", "sidetone";
+	interrupts = <0 17 0x4>, /* OCP compliant interrupt */
+		     <0 62 0x4>, /* TX interrupt */
+		     <0 63 0x4>, /* RX interrupt */
+		     <0 4 0x4>;  /* Sidetone */
+	interrupt-names = "common", "tx", "rx", "sidetone";
+	interrupt-parent = <&intc>;
+	ti,buffer-size = <1280>;
+	ti,hwmods = "mcbsp2";
+};
@@ -0,0 +1,17 @@
+* Texas Instruments SoC with twl4030 based audio setups
+
+Required properties:
+- compatible: "ti,omap-twl4030"
+- ti,model: Name of the sound card (for example "omap3beagle")
+- ti,mcbsp: phandle for the McBSP node
+- ti,codec: phandle for the twl4030 audio node
+
+Example:
+
+sound {
+	compatible = "ti,omap-twl4030";
+	ti,model = "omap3beagle";
+
+	ti,mcbsp = <&mcbsp2>;
+	ti,codec = <&twl_audio>;
+};
@@ -0,0 +1,20 @@
+Texas Instruments - tlv320aic3x Codec module
+
+The tlv320aic3x serial control bus communicates through I2C protocols
+
+Required properties:
+- compatible - "string" -  "ti,tlv320aic3x"
+- reg - <int> -  I2C slave address
+
+
+Optional properties:
+
+- gpio-reset - gpio pin number used for codec reset
+- ai3x-gpio-func - <array of 2 int> - AIC3X_GPIO1 & AIC3X_GPIO2 Functionality
+
+Example:
+
+tlv320aic3x: tlv320aic3x@1b {
+	compatible = "ti,tlv320aic3x";
+	reg = <0x1b>;
+};
@@ -579,7 +579,7 @@ Why:	KVM tracepoints provide mostly equivalent information in a much more
 ----------------------------

 What:	at91-mci driver ("CONFIG_MMC_AT91")
-When:	3.7
+When:	3.8
 Why:	There are two mci drivers: at91-mci and atmel-mci. The PDC support
 	was added to atmel-mci as a first step to support more chips.
 	Then at91-mci was kept only for old IP versions (on at91rm9200 and
@@ -21,6 +21,7 @@ Supported adapters:
  * Intel DH89xxCC (PCH)
  * Intel Panther Point (PCH)
  * Intel Lynx Point (PCH)
+  * Intel Lynx Point-LP (PCH)
   Datasheets: Publicly available at the Intel website

 On Intel Patsburg and later chipsets, both the normal host SMBus controller
@@ -3388,7 +3388,7 @@ M:	"Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
 L:	linux-i2c@vger.kernel.org
 W:	http://i2c.wiki.kernel.org/
 T:	quilt kernel.org/pub/linux/kernel/people/jdelvare/linux-2.6/jdelvare-i2c/
-T:	git git://git.fluff.org/bjdooks/linux.git
+T:	git git://git.pengutronix.de/git/wsa/linux.git
 S:	Maintained
 F:	Documentation/i2c/
 F:	drivers/i2c/
@@ -1,7 +1,7 @@
 VERSION = 3
 PATCHLEVEL = 6
 SUBLEVEL = 0
-EXTRAVERSION = -rc3
+EXTRAVERSION = -rc6
 NAME = Saber-toothed Squirrel

 # *DOCUMENTATION*
@@ -6,7 +6,7 @@ config ARM
 	select HAVE_DMA_API_DEBUG
 	select HAVE_IDE if PCI || ISA || PCMCIA
 	select HAVE_DMA_ATTRS
-	select HAVE_DMA_CONTIGUOUS if (CPU_V6 || CPU_V6K || CPU_V7)
+	select HAVE_DMA_CONTIGUOUS if MMU
 	select HAVE_MEMBLOCK
 	select RTC_LIB
 	select SYS_SUPPORTS_APM_EMULATION
@@ -356,15 +356,15 @@ choice
 		  is nothing connected to read from the DCC.

 	config DEBUG_SEMIHOSTING
-		bool "Kernel low-level debug output via semihosting I"
+		bool "Kernel low-level debug output via semihosting I/O"
 		help
 		  Semihosting enables code running on an ARM target to use
 		  the I/O facilities on a host debugger/emulator through a
-		  simple SVC calls. The host debugger or emulator must have
+		  simple SVC call. The host debugger or emulator must have
 		  semihosting enabled for the special svc call to be trapped
 		  otherwise the kernel will crash.

-		  This is known to work with OpenOCD, as wellas
+		  This is known to work with OpenOCD, as well as
 		  ARM's Fast Models, or any other controlling environment
 		  that implements semihosting.

@@ -284,10 +284,10 @@ zImage Image xipImage bootpImage uImage: vmlinux
 zinstall uinstall install: vmlinux
 	$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $@

-%.dtb:
+%.dtb: scripts
 	$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/$@

-dtbs:
+dtbs: scripts
 	$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/$@

 # We use MRPROPER_FILES and CLEAN_FILES now
@@ -659,10 +659,14 @@ __armv7_mmu_cache_on:
 #ifdef CONFIG_CPU_ENDIAN_BE8
 		orr	r0, r0, #1 << 25	@ big-endian page tables
 #endif
+		mrcne   p15, 0, r6, c2, c0, 2   @ read ttb control reg
 		orrne	r0, r0, #1		@ MMU enabled
 		movne	r1, #0xfffffffd		@ domain 0 = client
+		bic     r6, r6, #1 << 31        @ 32-bit translation system
+		bic     r6, r6, #3 << 0         @ use only ttbr0
 		mcrne	p15, 0, r3, c2, c0, 0	@ load page table pointer
 		mcrne	p15, 0, r1, c3, c0, 0	@ load domain access control
+		mcrne   p15, 0, r6, c2, c0, 2   @ load ttb control
 #endif
 		mcr	p15, 0, r0, c7, c5, 4	@ ISB
 		mcr	p15, 0, r0, c1, c0, 0	@ load control register
@@ -15,7 +15,7 @@
 	compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";

 	chosen {
-		bootargs = "128M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+		bootargs = "console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
 	};

 	ahb {
@@ -33,7 +33,7 @@ CONFIG_AEABI=y
 CONFIG_FORCE_MAX_ZONEORDER=13
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096"
+CONFIG_CMDLINE="console=tty0 console=ttySC1,115200 earlyprintk=sh-sci.1,115200 ignore_loglevel root=/dev/nfs ip=dhcp nfsroot=,rsize=4096,wsize=4096 rw"
 CONFIG_CMDLINE_FORCE=y
 CONFIG_KEXEC=y
 CONFIG_VFP=y
@@ -320,4 +320,12 @@
 	.size \name , . - \name
 	.endm

+	.macro check_uaccess, addr:req, size:req, limit:req, tmp:req, bad:req
+#ifndef CONFIG_CPU_USE_DOMAINS
+	adds	\tmp, \addr, #\size - 1
+	sbcccs	\tmp, \tmp, \limit
+	bcs	\bad
+#endif
+	.endm
+
 #endif /* __ASM_ASSEMBLER_H__ */
@@ -202,6 +202,13 @@ static inline void dma_free_writecombine(struct device *dev, size_t size,
 	return dma_free_attrs(dev, size, cpu_addr, dma_handle, &attrs);
 }

+/*
+ * This can be called during early boot to increase the size of the atomic
+ * coherent DMA pool above the default value of 256KiB. It must be called
+ * before postcore_initcall.
+ */
+extern void __init init_dma_coherent_pool_size(unsigned long size);
+
 /*
 * This can be called during boot to increase the size of the consistent
 * DMA region above it's default value of 2MB. It must be called before the
--- a/Show More
+++ b/Show More