gecko/gfx/thebes/gfxBlur.h

164 lines
5.9 KiB
C++

/* -*- Mode: C++; tab-width: 4; indent-tabs-mode: nil; c-basic-offset: 4 -*-
* ***** BEGIN LICENSE BLOCK *****
* Version: MPL 1.1/GPL 2.0/LGPL 2.1
*
* The contents of this file are subject to the Mozilla Public License Version
* 1.1 (the "License"); you may not use this file except in compliance with
* the License. You may obtain a copy of the License at
* http://www.mozilla.org/MPL/
*
* Software distributed under the License is distributed on an "AS IS" basis,
* WITHOUT WARRANTY OF ANY KIND, either express or implied. See the License
* for the specific language governing rights and limitations under the
* License.
*
* The Original Code is gfx thebes code.
*
* The Initial Developer of the Original Code is Mozilla Foundation.
* Portions created by the Initial Developer are Copyright (C) 2008
* the Initial Developer. All Rights Reserved.
*
* Contributor(s):
* Eric Butler <zantifon@gmail.com>
*
* Alternatively, the contents of this file may be used under the terms of
* either the GNU General Public License Version 2 or later (the "GPL"), or
* the GNU Lesser General Public License Version 2.1 or later (the "LGPL"),
* in which case the provisions of the GPL or the LGPL are applicable instead
* of those above. If you wish to allow use of your version of this file only
* under the terms of either the GPL or the LGPL, and not to allow others to
* use your version of this file under the terms of the MPL, indicate your
* decision by deleting the provisions above and replace them with the notice
* and other provisions required by the GPL or the LGPL. If you do not delete
* the provisions above, a recipient may use your version of this file under
* the terms of any one of the MPL, the GPL or the LGPL.
*
* ***** END LICENSE BLOCK ***** */
#ifndef GFX_BLUR_H
#define GFX_BLUR_H
#include "gfxContext.h"
#include "gfxImageSurface.h"
#include "gfxTypes.h"
#include "gfxUtils.h"
#include "nsRect.h"
/**
* Implementation of a triple box blur approximation of a Gaussian blur.
*
* A Gaussian blur is good for blurring because, when done independently
* in the horizontal and vertical directions, it matches the result that
* would be obtained using a different (rotated) set of axes. A triple
* box blur is a very close approximation of a Gaussian.
*
* Creates an 8-bit alpha channel context for callers to draw in,
* spreads the contents of that context, blurs the contents, and applies
* it as an alpha mask on a different existing context.
*
* A spread N makes each output pixel the maximum value of all source
* pixels within a square of side length 2N+1 centered on the output pixel.
*
* A temporary surface is created in the Init function. The caller then draws
* any desired content onto the context acquired through GetContext, and lastly
* calls Paint to apply the blurred content as an alpha mask.
*/
class THEBES_API gfxAlphaBoxBlur
{
public:
gfxAlphaBoxBlur();
~gfxAlphaBoxBlur();
/**
* Constructs a box blur and initializes the temporary surface.
* @param aRect The coordinates of the surface to create in device units.
*
* @param aBlurRadius The blur radius in pixels. This is the radius of
* the entire (triple) kernel function. Each individual box blur has
* radius approximately 1/3 this value, or diameter approximately 2/3
* this value. This parameter should nearly always be computed using
* CalculateBlurRadius, below.
*
* @param aDirtyRect A pointer to a dirty rect, measured in device units, if available.
* This will be used for optimizing the blur operation. It is safe to pass NULL here.
*
* @param aSkipRect A pointer to a rect, measured in device units, that represents an area
* where blurring is unnecessary and shouldn't be done for speed reasons. It is safe to
* pass NULL here.
*/
gfxContext* Init(const gfxRect& aRect,
const gfxIntSize& aSpreadRadius,
const gfxIntSize& aBlurRadius,
const gfxRect* aDirtyRect,
const gfxRect* aSkipRect);
/**
* Returns the context that should be drawn to supply the alpha mask to be
* blurred. If the returned surface is null, then there was an error in
* its creation.
*/
gfxContext* GetContext()
{
return mContext;
}
/**
* Premultiplies the image by the given alpha.
*/
void PremultiplyAlpha(gfxFloat alpha);
/**
* Does the actual blurring/spreading and mask applying. Users of this
* object must have drawn whatever they want to be blurred onto the internal
* gfxContext returned by GetContext before calling this.
*
* @param aDestinationCtx The graphics context on which to apply the
* blurred mask.
*/
void Paint(gfxContext* aDestinationCtx, const gfxPoint& offset = gfxPoint(0.0, 0.0));
/**
* Calculates a blur radius that, when used with box blur, approximates
* a Gaussian blur with the given standard deviation. The result of
* this function should be used as the aBlurRadius parameter to Init,
* above.
*/
static gfxIntSize CalculateBlurRadius(const gfxPoint& aStandardDeviation);
protected:
/**
* The spread radius, in pixels.
*/
gfxIntSize mSpreadRadius;
/**
* The blur radius, in pixels.
*/
gfxIntSize mBlurRadius;
/**
* The context of the temporary alpha surface.
*/
nsRefPtr<gfxContext> mContext;
/**
* The temporary alpha surface.
*/
nsRefPtr<gfxImageSurface> mImageSurface;
/**
* A copy of the dirty rect passed to Init(). This will only be valid if
* mHasDirtyRect is TRUE.
*/
gfxRect mDirtyRect;
/**
* A rect indicating the area where blurring is unnecessary, and the blur
* algorithm should skip over it.
*/
nsIntRect mSkipRect;
PRPackedBool mHasDirtyRect;
};
#endif /* GFX_BLUR_H */