gecko/modules/libpr0n/public/imgIEncoder.idl

/* -*- Mode: C++; tab-width: 2; indent-tabs-mode: nil; c-basic-offset: 2 -*-
 * ***** BEGIN LICENSE BLOCK *****
 * Version: MPL 1.1/GPL 2.0/LGPL 2.1
 *
 * The contents of this file are subject to the Mozilla Public License Version
 * 1.1 (the "License"); you may not use this file except in compliance with
 * the License. You may obtain a copy of the License at
 * http://www.mozilla.org/MPL/
 *
 * Software distributed under the License is distributed on an "AS IS" basis,
 * WITHOUT WARRANTY OF ANY KIND, either express or implied. See the License
 * for the specific language governing rights and limitations under the
 * License.
 *
 * The Original Code is Oracle Corporation code.
 *
 * The Initial Developer of the Original Code is Oracle Corporation.
 * Portions created by the Initial Developer are Copyright (C) 2005
 * the Initial Developer. All Rights Reserved.
 *
 * Contributor(s):
 *   Stuart Parmenter <pavlov@pavlov.net>
 *   Brett Wilson <brettw@gmail.com>
 *   Justin Dolske <dolske@mozilla.com>
 *
 * Alternatively, the contents of this file may be used under the terms of
 * either the GNU General Public License Version 2 or later (the "GPL"), or
 * the GNU Lesser General Public License Version 2.1 or later (the "LGPL"),
 * in which case the provisions of the GPL or the LGPL are applicable instead
 * of those above. If you wish to allow use of your version of this file only
 * under the terms of either the GPL or the LGPL, and not to allow others to
 * use your version of this file under the terms of the MPL, indicate your
 * decision by deleting the provisions above and replace them with the notice
 * and other provisions required by the GPL or the LGPL. If you do not delete
 * the provisions above, a recipient may use your version of this file under
 * the terms of any one of the MPL, the GPL or the LGPL.
 *
 * ***** END LICENSE BLOCK ***** */

#include "nsISupports.idl"
#include "nsIInputStream.idl"

/**
 * imgIEncoder interface
 */
[scriptable, uuid(ba3a854b-fb8d-4881-8af9-5849df10e5e5)]
interface imgIEncoder : nsIInputStream
{
  // Possible values for outputOptions. Multiple values are semicolon-separated.
  //
  // PNG:
  // ----
  // usetransparency=[yes|no|none]  --  default: "yes"
  //     Overrides default from input format. "no" and "none" are equivalent.
  //
  //
  // APNG:
  // -----
  // The following options can be used with startImageEncode():
  //
  // usetransparency=[yes|no|none]  --  default: "yes"
  //     Overrides default from input format. "no" and "none" are equivalent.
  // skipfirstframe=[yes|no]  --  default: "no"
  //     Controls display of the first frame in animations. PNG-only clients always
  //     display the first frame (and only that frame).
  // frames=#  --  default: "1"
  //     Total number of frames in the image. The first frame, even if skipped, is
  //     always included in the count.
  // plays=#  --  default: "0"
  //     Number of times to play the animation sequence. "0" will repeat forever.
  //
  //
  // The following options can be used for each frame, with addImageFrame():
  //
  // usetransparency=[yes|no|none]  --  default: "yes"
  //     Overrides default from input format. "no" and "none" are equivalent.
  // delay=#  --  default: "500"
  //     Number of milliseconds to display the frame, before moving to the next frame.
  // dispose=[none|background|previous]  --  default: "none"
  //     What to do with the image's canvas before rendering the next frame. See APNG spec.
  // blend=[source|over]  --  default: "source"
  //     How to render the new frame on the canvas. See APNG spec.
  // xoffset=#  --  default: "0"
  // yoffset=#  --  default: "0"
  //     Where to draw the frame, relative to the canvas.
  //
  //
  // JPEG:
  // -----
  //
  // quality=#  --  default: "50"
  //    Quality of compression, 0-100 (worst-best). 


  // Possible values for input format (note that not all image formats
  // support saving alpha channels):

    // Input is RGB each pixel is represented by three bytes:
    // R, G, and B (in that order, regardless of host endianness)
  const PRUint32 INPUT_FORMAT_RGB = 0;

    // Input is RGB each pixel is represented by four bytes:
    // R, G, and B (in that order, regardless of host endianness).
    // POST-MULTIPLIED alpha us used (50% transparent red is 0xff000080)
  const PRUint32 INPUT_FORMAT_RGBA = 1;

    // Input is host-endian ARGB: On big-endian machines each pixel is therefore
    // ARGB, and for little-endian machiens (Intel) each pixel is BGRA
    // (This is used by canvas to match it's internal representation)
    //
    // PRE-MULTIPLIED alpha is used (That is, 50% transparent red is 0x80800000,
    // not 0x80ff0000
  const PRUint32 INPUT_FORMAT_HOSTARGB = 2;

  /* data - list of bytes in the format specified by inputFormat
   * width  - width in pixels
   * height - height in pixels
   * stride - number of bytes per row in the image
   *          Normally (width*3) or (width*4), depending on your input format,
   *          but some data uses padding at the end of each row, which would
   *          be extra.
   * inputFormat - one of INPUT_FORMAT_* specifying the format of data
   * outputOptions - semicolon-delimited list of name=value pairs that can
   *                 give options to the output encoder. Options are encoder-
   *                 specific. Just give empty string for default behavior.
   */
  void initFromData([array, size_is(length), const] in PRUint8 data,
                    in unsigned long length,
                    in PRUint32 width,
                    in PRUint32 height,
                    in PRUint32 stride,
                    in PRUint32 inputFormat,
                    in AString outputOptions);

  /*
   * For encoding images which may contain multiple frames, the 1-shot
   * initFromData() interface is too simplistic. The alternative is to
   * use startImageEncode(), call addImageFrame() one or more times, and
   * then finish initialization with endImageEncode().
   *
   * The arguments are basically the same as in initFromData().
   */
  void startImageEncode(in PRUint32 width,
                    in PRUint32 height,
                    in PRUint32 inputFormat,
                    in AString outputOptions);

  void addImageFrame( [array, size_is(length), const] in PRUint8 data,
                    in unsigned long length,
                    in PRUint32 width,
                    in PRUint32 height,
                    in PRUint32 stride,
                    in PRUint32 frameFormat,
                    in AString frameOptions);

  void endImageEncode();
};