In the near future, the driver core is going to not allow direct access
to the driver_data pointer in struct device. Instead, the functions
dev_get_drvdata() and dev_set_drvdata() should be used. These functions
have been around since the beginning, so are backwards compatible with
all older kernel versions.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for block drivers to report their requested nodename
to userspace. It also updates a number of block drivers to provide the
needed subdirectory and device name to be used for them.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for USB drivers to report their requested nodename to
userspace. It also updates a number of USB drivers to provide the
needed subdirectory and device name to be used for them.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for misc devices to report their requested nodename to
userspace. It also updates a number of misc drivers to provide the
needed subdirectory and device name to be used for them.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the nodename callback for struct class, struct device_type and
struct device, to allow drivers to send userspace hints on the device
name and subdirectory that should be used for it.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As we're allocating the firmware name dynamically, we no longer need this
definition.
This patch must be applied only after the 5 previous patches from this pacth
set have been applied.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This converts resource and IRQ getbyname functions for the platform
bus to use const char *, I ran into compiler moanings when I tried
using a const char * for looking up a certain resource.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new bus notifier event which is emitted _after_ a
device is removed from its driver. This event will be used by the
dma-api debug code to check if a driver has released all dma allocations
for that device.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
During bootup performance tracing we see repeated occurrences of
/sys/kernel/uid/* events for the same uid, leading to a,
in this case, rather pointless userspace processing for the
same uid over and over.
This is usually caused by tools which change their uid to "nobody",
to run without privileges to read data supplied by untrusted users.
This change delays the execution of the (already existing) scheduled
work, to cleanup the uid after one second, so the allocated and announced
uid can possibly be re-used by another process.
This is the current behavior, where almost every invocation of a
binary, which changes the uid, creates two events:
$ read START < /sys/kernel/uevent_seqnum; \
for i in `seq 100`; do su --shell=/bin/true bin; done; \
read END < /sys/kernel/uevent_seqnum; \
echo $(($END - $START))
178
With the delayed cleanup, we get only two events, and userspace finishes
a bit faster too:
$ read START < /sys/kernel/uevent_seqnum; \
for i in `seq 100`; do su --shell=/bin/true bin; done; \
read END < /sys/kernel/uevent_seqnum; \
echo $(($END - $START))
1
Acked-by: Dhaval Giani <dhaval@linux.vnet.ibm.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: Logic to move non pinned timers
timers: /proc/sys sysctl hook to enable timer migration
timers: Identifying the existing pinned timers
timers: Framework for identifying pinned timers
timers: allow deferrable timers for intervals tv2-tv5 to be deferred
Fix up conflicts in kernel/sched.c and kernel/timer.c manually
* 'timers-for-linus-clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: prevent selection of low resolution clocksourse also for nohz=on
clocksource: sanity check sysfs clocksource changes
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (103 commits)
powerpc: Fix bug in move of altivec code to vector.S
powerpc: Add support for swiotlb on 32-bit
powerpc/spufs: Remove unused error path
powerpc: Fix warning when printing a resource_size_t
powerpc/xmon: Remove unused variable in xmon.c
powerpc/pseries: Fix warnings when printing resource_size_t
powerpc: Shield code specific to 64-bit server processors
powerpc: Separate PACA fields for server CPUs
powerpc: Split exception handling out of head_64.S
powerpc: Introduce CONFIG_PPC_BOOK3S
powerpc: Move VMX and VSX asm code to vector.S
powerpc: Set init_bootmem_done on NUMA platforms as well
powerpc/mm: Fix a AB->BA deadlock scenario with nohash MMU context lock
powerpc/mm: Fix some SMP issues with MMU context handling
powerpc: Add PTRACE_SINGLEBLOCK support
fbdev: Add PLB support and cleanup DCR in xilinxfb driver.
powerpc/virtex: Add ml510 reference design device tree
powerpc/virtex: Add Xilinx ML510 reference design support
powerpc/virtex: refactor intc driver and add support for i8259 cascading
powerpc/virtex: Add support for Xilinx PCI host bridge
...
The V3 regulator can be configured with an external resistor
connected to the feedback pin (R24 in the data sheet) to
increase the voltage range.
For example, hx4700 has R24 = 3.32 kOhm to achieve a maximum
V3 voltage of 1.55 V which is needed for 624 MHz CPU frequency.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch adds regulator drivers for National Semiconductors LP3971 PMIC.
This LP3971 PMIC controller has 3 DC/DC voltage converters and 5 low
drop-out (LDO) regulators. LP3971 PMIC controller uses I2C interface.
Reviewed-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The userspace-consumer driver allows control of voltage and current
regulator state from userspace. This is required for fine-grained
power management of devices that are completely controller by userspace
applications, e.g. a GPS transciever connected to a serial port.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The Maxim 1586 regulator is a voltage regulator with 2
voltage outputs, specially suitable for Marvell PXA
chips. One output is in the range of required VCC_CORE by
the PXA27x chips, the other in the VCC_USIM required as well
by PXA27x chips.
The chip is controlled through the I2C bus.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (53 commits)
.gitignore: ignore *.lzma files
kbuild: add generic --set-str option to scripts/config
kbuild: simplify argument loop in scripts/config
kbuild: handle non-existing options in scripts/config
kallsyms: generalize text region handling
kallsyms: support kernel symbols in Blackfin on-chip memory
documentation: make version fix
kbuild: fix a compile warning
gitignore: Add GNU GLOBAL files to top .gitignore
kbuild: fix delay in setlocalversion on readonly source
README: fix misleading pointer to the defconf directory
vmlinux.lds.h update
kernel-doc: cleanup perl script
Improve vmlinux.lds.h support for arch specific linker scripts
kbuild: fix headers_exports with boolean expression
kbuild/headers_check: refine extern check
kbuild: fix "Argument list too long" error for "make headers_check",
ignore *.patch files
Remove bashisms from scripts
menu: fix embedded menu presentation
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
IB/mlx4: Add strong ordering to local inval and fast reg work requests
IB/ehca: Remove superfluous bitmasks from QP control block
RDMA/cxgb3: Limit fast register size based on T3 limitations
RDMA/cxgb3: Report correct port state and MTU
mlx4_core: Add module parameter for number of MTTs per segment
IB/mthca: Add module parameter for number of MTTs per segment
RDMA/nes: Fix off-by-one bugs in reset_adapter_ne020() and init_serdes()
infiniband: Remove void casts
IB/ehca: Increment version number
IB/ehca: Remove unnecessary memory operations for userspace queue pairs
IB/ehca: Fall back to vmalloc() for big allocations
IB/ehca: Replace vmalloc() with kmalloc() for queue allocation
In addition to KT_DEAD which has limited support for diacriticals,
there is KT_DEAD2 that can support 256 criticals, so let's advertise
it in <linux/keyboard.h>.
This lets userland know abut the drivers/char/keyboard.c function
k_dead2, which supports more than the few trivial ones that k_dead
supports.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc: (25 commits)
atmel-mci: add MCI2 register definitions
atmel-mci: Integrate AT91 specific definition in header file
tmio_mmc: allow compilation for ASIC3
mmc_block: do not DMA to stack
sdhci: Print ADMA status and pointer on debug
tmio_mmc: fix clock setup
tmio_mmc: map SD control registers after enabling the MFD cell
tmio_mmc: correct probe return value for num_resources != 3
tmio_mmc: don't use set_irq_type
tmio_mmc: add bus_shift support
MFD,mmc: tmio_mmc: make HCLK configurable
mmc_spi: don't use EINVAL for possible transmission errors
cb710: more cleanup for the DEBUG case.
sdhci: platform driver for SDHCI
mxcmmc: remove frequency workaround
cb710: handle DEBUG define in Makefile
cb710: add missing parenthesis
cb710: fix printk format string
mmc: Driver for CB710/720 memory card reader (MMC part)
pxamci: add regulator support.
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: fix inverted wheel for bluetooth version of apple mighty mouse
HID: no more reinitializtion is needed in post_reset
HID: hidraw -- fix comment about accepted devices
HID: Multitouch support for the N-Trig touchscreen
HID: add new multitouch and digitizer contants
HID: autocentering support for Logitech Force 3D Pro
HID: fix hid-ff drivers so that devices work even without ff support
HID: force feedback support for SmartJoy PLUS PS2/USB adapter
HID: Wacom Graphire Bluetooth driver
HID: autocentering support for Logitech G25 Racing Wheel
