With so many counter addresses recently discovered as being wrong, it is
desirable to at least have a central database of information, rather
than two: one through the SYS_COUNT_* registers (used for
ndo_get_stats64), and the other through the offset field of struct
ocelot_stat_layout elements (used for ethtool -S).
The strategy will be to keep the SYS_COUNT_* definitions as the single
source of truth, but for that we need to expand our current definitions
to cover all registers. Then we need to convert the ocelot region
creation logic, and stats worker, to the read semantics imposed by going
through SYS_COUNT_* absolute register addresses, rather than offsets
of 32-bit words relative to SYS_COUNT_RX_OCTETS (which should have been
SYS_CNT, by the way).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ocelot counters are 32-bit and require periodic reading, every 2
seconds, by ocelot_port_update_stats(), so that wraparounds are
detected.
Currently, the counters reported by ocelot_get_stats64() come from the
32-bit hardware counters directly, rather than from the 64-bit
accumulated ocelot->stats, and this is a problem for their integrity.
The strategy is to make ocelot_get_stats64() able to cherry-pick
individual stats from ocelot->stats the way in which it currently reads
them out from SYS_COUNT_* registers. But currently it can't, because
ocelot->stats is an opaque u64 array that's used only to feed data into
ethtool -S.
To solve that problem, we need to make ocelot->stats indexable, and
associate each element with an element of struct ocelot_stat_layout used
by ethtool -S.
This makes ocelot_stat_layout a fat (and possibly sparse) array, so we
need to change the way in which we access it. We no longer need
OCELOT_STAT_END as a sentinel, because we know the array's size
(OCELOT_NUM_STATS). We just need to skip the array elements that were
left unpopulated for the switch revision (ocelot, felix, seville).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_get_stats64() currently runs unlocked and therefore may collide
with ocelot_port_update_stats() which indirectly accesses the same
counters. However, ocelot_get_stats64() runs in atomic context, and we
cannot simply take the sleepable ocelot->stats_lock mutex. We need to
convert it to an atomic spinlock first. Do that as a preparatory change.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reading stats using the SYS_COUNT_* register definitions is only used by
ocelot_get_stats64() from the ocelot switchdev driver, however,
currently the bucket definitions are incorrect.
Separately, on both RX and TX, we have the following problems:
- a 256-1023 bucket which actually tracks the 256-511 packets
- the 1024-1526 bucket actually tracks the 512-1023 packets
- the 1527-max bucket actually tracks the 1024-1526 packets
=> nobody tracks the packets from the real 1527-max bucket
Additionally, the RX_PAUSE, RX_CONTROL, RX_LONGS and RX_CLASSIFIED_DROPS
all track the wrong thing. However this doesn't seem to have any
consequence, since ocelot_get_stats64() doesn't use these.
Even though this problem only manifests itself for the switchdev driver,
we cannot split the fix for ocelot and for DSA, since it requires fixing
the bucket definitions from enum ocelot_reg, which makes us necessarily
adapt the structures from felix and seville as well.
Fixes: 84705fc165 ("net: dsa: felix: introduce support for Seville VSC9953 switch")
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull char / misc driver updates from Greg KH:
"Here is the large set of char and misc and other driver subsystem
changes for 6.0-rc1.
Highlights include:
- large set of IIO driver updates, additions, and cleanups
- new habanalabs device support added (loads of register maps much
like GPUs have)
- soundwire driver updates
- phy driver updates
- slimbus driver updates
- tiny virt driver fixes and updates
- misc driver fixes and updates
- interconnect driver updates
- hwtracing driver updates
- fpga driver updates
- extcon driver updates
- firmware driver updates
- counter driver update
- mhi driver fixes and updates
- binder driver fixes and updates
- speakup driver fixes
All of these have been in linux-next for a while without any reported
problems"
* tag 'char-misc-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (634 commits)
drivers: lkdtm: fix clang -Wformat warning
char: remove VR41XX related char driver
misc: Mark MICROCODE_MINOR unused
spmi: trace: fix stack-out-of-bound access in SPMI tracing functions
dt-bindings: iio: adc: Add compatible for MT8188
iio: light: isl29028: Fix the warning in isl29028_remove()
iio: accel: sca3300: Extend the trigger buffer from 16 to 32 bytes
iio: fix iio_format_avail_range() printing for none IIO_VAL_INT
iio: adc: max1027: unlock on error path in max1027_read_single_value()
iio: proximity: sx9324: add empty line in front of bullet list
iio: magnetometer: hmc5843: Remove duplicate 'the'
iio: magn: yas530: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: magnetometer: ak8974: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: veml6030: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: vcnl4035: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: vcnl4000: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr() macros
iio: light: tsl2591: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
iio: light: tsl2583: Use DEFINE_RUNTIME_DEV_PM_OPS and pm_ptr()
iio: light: isl29028: Use DEFINE_RUNTIME_DEV_PM_OPS() and pm_ptr()
iio: light: gp2ap002: Switch to DEFINE_RUNTIME_DEV_PM_OPS and pm_ptr()
...
In a future change we will need to remember the entire tc-taprio config
on all ports rather than just the base time, so use the
taprio_offload_get() helper function to replace ocelot_port->base_time
with ocelot_port->taprio.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When adjusting the PTP clock, the base time of the TAS configuration
will become unreliable. We need reset the TAS configuration by using a
new base time.
For example, if the driver gets a base time 0 of Qbv configuration from
user, and current time is 20000. The driver will set the TAS base time
to be 20000. After the PTP clock adjustment, the current time becomes
10000. If the TAS base time is still 20000, it will be a future time,
and TAS entry list will stop running. Another example, if the current
time becomes to be 10000000 after PTP clock adjust, a large time offset
can cause the hardware to hang.
This patch introduces a tas_clock_adjust() function to reset the TAS
module by using a new base time after the PTP clock adjustment. This can
avoid issues above.
Due to PTP clock adjustment can occur at any time, it may conflict with
the TAS configuration. We introduce a new TAS lock to serialize the
access to the TAS registers.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM driver updates from Arnd Bergmann:
"There are minor updates to SoC specific drivers for chips by Rockchip,
Samsung, NVIDIA, TI, NXP, i.MX, Qualcomm, and Broadcom.
Noteworthy driver changes include:
- Several conversions of DT bindings to yaml format.
- Renesas adds driver support for R-Car V4H, RZ/V2M and RZ/G2UL SoCs.
- Qualcomm adds a bus driver for the SSC (Snapdragon Sensor Core),
and support for more chips in the RPMh power domains and the
soc-id.
- NXP has a new driver for the HDMI blk-ctrl on i.MX8MP.
- Apple M1 gains support for the on-chip NVMe controller, making it
possible to finally use the internal disks. This also includes SoC
drivers for their RTKit IPC and for the SART DMA address filter.
For other subsystems that merge their drivers through the SoC tree, we
have
- Firmware drivers for the ARM firmware stack including TEE, OP-TEE,
SCMI and FF-A get a number of smaller updates and cleanups. OP-TEE
now has a cache for firmware argument structures as an
optimization, and SCMI now supports the 3.1 version of the
specification.
- Reset controller updates to Amlogic, ASpeed, Renesas and ACPI
drivers
- Memory controller updates for Tegra, and a few updates for other
platforms"
* tag 'arm-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (159 commits)
memory: tegra: Add MC error logging on Tegra186 onward
memory: tegra: Add memory controller channels support
memory: tegra: Add APE memory clients for Tegra234
memory: tegra: Add Tegra234 support
nvme-apple: fix sparse endianess warnings
soc/tegra: pmc: Document core domain fields
soc: qcom: pdr: use static for servreg_* variables
soc: imx: fix semicolon.cocci warnings
soc: renesas: R-Car V3U is R-Car Gen4
soc: imx: add i.MX8MP HDMI blk-ctrl
soc: imx: imx8m-blk-ctrl: Add i.MX8MP media blk-ctrl
soc: imx: add i.MX8MP HSIO blk-ctrl
soc: imx: imx8m-blk-ctrl: set power device name
soc: qcom: llcc: Add sc8180x and sc8280xp configurations
dt-bindings: arm: msm: Add sc8180x and sc8280xp LLCC compatibles
soc/tegra: pmc: Select REGMAP
dt-bindings: reset: st,sti-powerdown: Convert to yaml
dt-bindings: reset: st,sti-picophyreset: Convert to yaml
dt-bindings: reset: socfpga: Convert to yaml
dt-bindings: reset: snps,axs10x-reset: Convert to yaml
...
Pull networking updates from Jakub Kicinski:
"Core
----
- Support TCPv6 segmentation offload with super-segments larger than
64k bytes using the IPv6 Jumbogram extension header (AKA BIG TCP).
- Generalize skb freeing deferral to per-cpu lists, instead of
per-socket lists.
- Add a netdev statistic for packets dropped due to L2 address
mismatch (rx_otherhost_dropped).
- Continue work annotating skb drop reasons.
- Accept alternative netdev names (ALT_IFNAME) in more netlink
requests.
- Add VLAN support for AF_PACKET SOCK_RAW GSO.
- Allow receiving skb mark from the socket as a cmsg.
- Enable memcg accounting for veth queues, sysctl tables and IPv6.
BPF
---
- Add libbpf support for User Statically-Defined Tracing (USDTs).
- Speed up symbol resolution for kprobes multi-link attachments.
- Support storing typed pointers to referenced and unreferenced
objects in BPF maps.
- Add support for BPF link iterator.
- Introduce access to remote CPU map elements in BPF per-cpu map.
- Allow middle-of-the-road settings for the
kernel.unprivileged_bpf_disabled sysctl.
- Implement basic types of dynamic pointers e.g. to allow for
dynamically sized ringbuf reservations without extra memory copies.
Protocols
---------
- Retire port only listening_hash table, add a second bind table
hashed by port and address. Avoid linear list walk when binding to
very popular ports (e.g. 443).
- Add bridge FDB bulk flush filtering support allowing user space to
remove all FDB entries matching a condition.
- Introduce accept_unsolicited_na sysctl for IPv6 to implement
router-side changes for RFC9131.
- Support for MPTCP path manager in user space.
- Add MPTCP support for fallback to regular TCP for connections that
have never connected additional subflows or transmitted
out-of-sequence data (partial support for RFC8684 fallback).
- Avoid races in MPTCP-level window tracking, stabilize and improve
throughput.
- Support lockless operation of GRE tunnels with seq numbers enabled.
- WiFi support for host based BSS color collision detection.
- Add support for SO_TXTIME/SCM_TXTIME on CAN sockets.
- Support transmission w/o flow control in CAN ISOTP (ISO 15765-2).
- Support zero-copy Tx with TLS 1.2 crypto offload (sendfile).
- Allow matching on the number of VLAN tags via tc-flower.
- Add tracepoint for tcp_set_ca_state().
Driver API
----------
- Improve error reporting from classifier and action offload.
- Add support for listing line cards in switches (devlink).
- Add helpers for reporting page pool statistics with ethtool -S.
- Add support for reading clock cycles when using PTP virtual clocks,
instead of having the driver convert to time before reporting. This
makes it possible to report time from different vclocks.
- Support configuring low-latency Tx descriptor push via ethtool.
- Separate Clause 22 and Clause 45 MDIO accesses more explicitly.
New hardware / drivers
----------------------
- Ethernet:
- Marvell's Octeon NIC PCI Endpoint support (octeon_ep)
- Sunplus SP7021 SoC (sp7021_emac)
- Add support for Renesas RZ/V2M (in ravb)
- Add support for MediaTek mt7986 switches (in mtk_eth_soc)
- Ethernet PHYs:
- ADIN1100 industrial PHYs (w/ 10BASE-T1L and SQI reporting)
- TI DP83TD510 PHY
- Microchip LAN8742/LAN88xx PHYs
- WiFi:
- Driver for pureLiFi X, XL, XC devices (plfxlc)
- Driver for Silicon Labs devices (wfx)
- Support for WCN6750 (in ath11k)
- Support Realtek 8852ce devices (in rtw89)
- Mobile:
- MediaTek T700 modems (Intel 5G 5000 M.2 cards)
- CAN:
- ctucanfd: add support for CTU CAN FD open-source IP core from
Czech Technical University in Prague
Drivers
-------
- Delete a number of old drivers still using virt_to_bus().
- Ethernet NICs:
- intel: support TSO on tunnels MPLS
- broadcom: support multi-buffer XDP
- nfp: support VF rate limiting
- sfc: use hardware tx timestamps for more than PTP
- mlx5: multi-port eswitch support
- hyper-v: add support for XDP_REDIRECT
- atlantic: XDP support (including multi-buffer)
- macb: improve real-time perf by deferring Tx processing to NAPI
- High-speed Ethernet switches:
- mlxsw: implement basic line card information querying
- prestera: add support for traffic policing on ingress and egress
- Embedded Ethernet switches:
- lan966x: add support for packet DMA (FDMA)
- lan966x: add support for PTP programmable pins
- ti: cpsw_new: enable bc/mc storm prevention
- Qualcomm 802.11ax WiFi (ath11k):
- Wake-on-WLAN support for QCA6390 and WCN6855
- device recovery (firmware restart) support
- support setting Specific Absorption Rate (SAR) for WCN6855
- read country code from SMBIOS for WCN6855/QCA6390
- enable keep-alive during WoWLAN suspend
- implement remain-on-channel support
- MediaTek WiFi (mt76):
- support Wireless Ethernet Dispatch offloading packet movement
between the Ethernet switch and WiFi interfaces
- non-standard VHT MCS10-11 support
- mt7921 AP mode support
- mt7921 IPv6 NS offload support
- Ethernet PHYs:
- micrel: ksz9031/ksz9131: cabletest support
- lan87xx: SQI support for T1 PHYs
- lan937x: add interrupt support for link detection"
* tag 'net-next-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1809 commits)
ptp: ocp: Add firmware header checks
ptp: ocp: fix PPS source selector debugfs reporting
ptp: ocp: add .init function for sma_op vector
ptp: ocp: vectorize the sma accessor functions
ptp: ocp: constify selectors
ptp: ocp: parameterize input/output sma selectors
ptp: ocp: revise firmware display
ptp: ocp: add Celestica timecard PCI ids
ptp: ocp: Remove #ifdefs around PCI IDs
ptp: ocp: 32-bit fixups for pci start address
Revert "net/smc: fix listen processing for SMC-Rv2"
ath6kl: Use cc-disable-warning to disable -Wdangling-pointer
selftests/bpf: Dynptr tests
bpf: Add dynptr data slices
bpf: Add bpf_dynptr_read and bpf_dynptr_write
bpf: Dynptr support for ring buffers
bpf: Add bpf_dynptr_from_mem for local dynptrs
bpf: Add verifier support for dynptrs
bpf: Suppress 'passing zero to PTR_ERR' warning
bpf: Introduce bpf_arch_text_invalidate for bpf_prog_pack
...
Pull power management updates from Rafael Wysocki:
"These add support for 'artificial' Energy Models in which power
numbers for different entities may be in different scales, add support
for some new hardware, fix bugs and clean up code in multiple places.
Specifics:
- Update the Energy Model support code to allow the Energy Model to
be artificial, which means that the power values may not be on a
uniform scale with other devices providing power information, and
update the cpufreq_cooling and devfreq_cooling thermal drivers to
support artificial Energy Models (Lukasz Luba).
- Make DTPM check the Energy Model type (Lukasz Luba).
- Fix policy counter decrementation in cpufreq if Energy Model is in
use (Pierre Gondois).
- Add CPU-based scaling support to passive devfreq governor (Saravana
Kannan, Chanwoo Choi).
- Update the rk3399_dmc devfreq driver (Brian Norris).
- Export dev_pm_ops instead of suspend() and resume() in the IIO
chemical scd30 driver (Jonathan Cameron).
- Add namespace variants of EXPORT[_GPL]_SIMPLE_DEV_PM_OPS and
PM-runtime counterparts (Jonathan Cameron).
- Move symbol exports in the IIO chemical scd30 driver into the
IIO_SCD30 namespace (Jonathan Cameron).
- Avoid device PM-runtime usage count underflows (Rafael Wysocki).
- Allow dynamic debug to control printing of PM messages (David
Cohen).
- Fix some kernel-doc comments in hibernation code (Yang Li, Haowen
Bai).
- Preserve ACPI-table override during hibernation (Amadeusz
Sławiński).
- Improve support for suspend-to-RAM for PSCI OSI mode (Ulf Hansson).
- Make Intel RAPL power capping driver support the RaptorLake and
AlderLake N processors (Zhang Rui, Sumeet Pawnikar).
- Remove redundant store to value after multiply in the RAPL power
capping driver (Colin Ian King).
- Add AlderLake processor support to the intel_idle driver (Zhang
Rui).
- Fix regression leading to no genpd governor in the PSCI cpuidle
driver and fix the riscv-sbi cpuidle driver to allow a genpd
governor to be used (Ulf Hansson).
- Fix cpufreq governor clean up code to avoid using kfree() directly
to free kobject-based items (Kevin Hao).
- Prepare cpufreq for powerpc's asm/prom.h cleanup (Christophe
Leroy).
- Make intel_pstate notify frequency invariance code when no_turbo is
turned on and off (Chen Yu).
- Add Sapphire Rapids OOB mode support to intel_pstate (Srinivas
Pandruvada).
- Make cpufreq avoid unnecessary frequency updates due to mismatch
between hardware and the frequency table (Viresh Kumar).
- Make remove_cpu_dev_symlink() clear the real_cpus mask to simplify
code (Viresh Kumar).
- Rearrange cpufreq_offline() and cpufreq_remove_dev() to make the
calling convention for some driver callbacks consistent (Rafael
Wysocki).
- Avoid accessing half-initialized cpufreq policies from the show()
and store() sysfs functions (Schspa Shi).
- Rearrange cpufreq_offline() to make the calling convention for some
driver callbacks consistent (Schspa Shi).
- Update CPPC handling in cpufreq (Pierre Gondois).
- Extend dev_pm_domain_detach() doc (Krzysztof Kozlowski).
- Move genpd's time-accounting to ktime_get_mono_fast_ns() (Ulf
Hansson).
- Improve the way genpd deals with its governors (Ulf Hansson).
- Update the turbostat utility to version 2022.04.16 (Len Brown, Dan
Merillat, Sumeet Pawnikar, Zephaniah E. Loss-Cutler-Hull, Chen Yu)"
* tag 'pm-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (94 commits)
PM: domains: Trust domain-idle-states from DT to be correct by genpd
PM: domains: Measure power-on/off latencies in genpd based on a governor
PM: domains: Allocate governor data dynamically based on a genpd governor
PM: domains: Clean up some code in pm_genpd_init() and genpd_remove()
PM: domains: Fix initialization of genpd's next_wakeup
PM: domains: Fixup QoS latency measurements for IRQ safe devices in genpd
PM: domains: Measure suspend/resume latencies in genpd based on governor
PM: domains: Move the next_wakeup variable into the struct gpd_timing_data
PM: domains: Allocate gpd_timing_data dynamically based on governor
PM: domains: Skip another warning in irq_safe_dev_in_sleep_domain()
PM: domains: Rename irq_safe_dev_in_no_sleep_domain() in genpd
PM: domains: Don't check PM_QOS_FLAG_NO_POWER_OFF in genpd
PM: domains: Drop redundant code for genpd always-on governor
PM: domains: Add GENPD_FLAG_RPM_ALWAYS_ON for the always-on governor
powercap: intel_rapl: remove redundant store to value after multiply
cpufreq: CPPC: Enable dvfs_possible_from_any_cpu
cpufreq: CPPC: Enable fast_switch
ACPI: CPPC: Assume no transition latency if no PCCT
ACPI: bus: Set CPPC _OSC bits for all and when CPPC_LIB is supported
ACPI: CPPC: Check _OSC for flexible address space
...
The NXP Cryptographic Acceleration and Assurance Module (CAAM)
can be used to protect user-defined data across system reboot:
- When the system is fused and boots into secure state, the master
key is a unique never-disclosed device-specific key
- random key is encrypted by key derived from master key
- data is encrypted using the random key
- encrypted data and its encrypted random key are stored alongside
- This blob can now be safely stored in non-volatile memory
On next power-on:
- blob is loaded into CAAM
- CAAM writes decrypted data either into memory or key register
Add functions to realize encrypting and decrypting into memory alongside
the CAAM driver.
They will be used in a later commit as a source for the trusted key
seal/unseal mechanism.
Reviewed-by: David Gstir <david@sigma-star.at>
Reviewed-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Tested-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Tested-by: Pankaj Gupta <pankaj.gupta@nxp.com>
Tested-by: Michael Walle <michael@walle.cc> # on ls1028a (non-E and E)
Tested-by: John Ernberg <john.ernberg@actia.se> # iMX8QXP
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org>
Update the VCAP filters to support multiple tag_8021q CPU ports.
TX works using a filter for VLAN ID on the ingress of the CPU port, with
a redirect and a VLAN pop action. This can be updated trivially by
amending the ingress port mask of this rule to match on all tag_8021q
CPU ports.
RX works using a filter for ingress port on the egress of the CPU port,
with a VLAN push action. Here we need to replicate these filters for
each tag_8021q CPU port, and let them all have the same action.
This means that the OCELOT_VCAP_ES0_TAG_8021Q_RXVLAN() cookie needs to
encode a unique value for every {user port, CPU port} pair it's given.
Do this by encoding the CPU port in the upper 16 bits of the cookie, and
the user port in the lower 16 bits.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a desire for the felix driver to gain support for multiple
tag_8021q CPU ports, but the current model prevents it.
This is because ocelot_apply_bridge_fwd_mask() only takes into
consideration whether a port is a tag_8021q CPU port, but not whose CPU
port it is.
We need a model where we can have a direct affinity between an ocelot
port and a tag_8021q CPU port. This serves as the basis for multiple CPU
ports.
Declare a "dsa_8021q_cpu" backpointer in struct ocelot_port which
encodes that affinity. Repurpose the "ocelot_set_dsa_8021q_cpu" API to
"ocelot_assign_dsa_8021q_cpu" to express the change of paradigm.
Note that this change makes the first practical use of the new
ocelot_port->index field in ocelot_port_unassign_dsa_8021q_cpu(), where
we need to remove the old tag_8021q CPU port from the reserved VLAN range.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more logic to ocelot_port_{,un}set_dsa_8021q_cpu() from the ocelot
switch lib by encapsulating the ocelot_apply_bridge_fwd_mask() call that
felix used to have.
This is necessary because the CPU port change procedure will also need
to do this, and it's good to reduce code duplication by having an entry
point in the ocelot switch lib that does all that is needed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull devfreq changes for 5.19-rc1 from Chanwoo Choi:
"1. Update devfreq core
- Add cpu based scaling support to passive governor. Some device like
cache might require the dynamic frequency scaling. But, it has very
tightly to cpu frequency. So that use passive governor to scale
the frequency according to current cpu frequency.
To decide the frequency of the device, the governor does one of the following:
: Derives the optimal devfreq device opp from required-opps property of
the parent cpu opp_table.
: Scales the device frequency in proportion to the CPU frequency. So, if
the CPUs are running at their max frequency, the device runs at its
max frequency. If the CPUs are running at their min frequency, the
device runs at its min frequency. It is interpolated for frequencies
in between.
2. Update devfreq drivers
- Update rk3399_dmc.c as following:
: Convert dt-binding document to YAML and deprecate unused properties.
: Use Hz units for the device-tree properties of rk3399_dmc.
: rk3399_dmc is able to set the idle time before changing the dmc clock.
Specify idle time parameters by using nano-second unit on dt bidning.
: Add new disable-freq properties to optimize the power-saving feature
of rk3399_dmc.
: Disable devfreq-event device on remove() to fix unbalanced
enable-disable count.
: Use devm_pm_opp_of_add_table()
: Block PMU (Power-Management Unit) transitions when scaling frequency
by ARM Trust Firmware in order to fix the conflict between PMU and DMC
(Dynamic Memory Controller)."
* tag 'devfreq-next-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: passive: Keep cpufreq_policy for possible cpus
PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
PM / devfreq: Add cpu based scaling support to passive governor
PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
PM / devfreq: rk3399_dmc: Block PMU during transitions
soc: rockchip: power-domain: Manage resource conflicts with firmware
PM / devfreq: rk3399_dmc: Avoid static (reused) profile
PM / devfreq: rk3399_dmc: Use devm_pm_opp_of_add_table()
PM / devfreq: rk3399_dmc: Disable edev on remove()
PM / devfreq: rk3399_dmc: Support new *-ns properties
PM / devfreq: rk3399_dmc: Support new disable-freq properties
PM / devfreq: rk3399_dmc: Use bitfield macro definitions for ODT_PD
PM / devfreq: rk3399_dmc: Drop excess timing properties
PM / devfreq: rk3399_dmc: Drop undocumented ondemand DT props
dt-bindings: devfreq: rk3399_dmc: Add more disable-freq properties
dt-bindings: devfreq: rk3399_dmc: Specify idle params in nanoseconds
dt-bindings: devfreq: rk3399_dmc: Fix Hz units
dt-bindings: devfreq: rk3399_dmc: Deprecate unused/redundant properties
dt-bindings: devfreq: rk3399_dmc: Convert to YAML
Currently the ocelot switch lib is unaware of the index of a struct
ocelot_port, since that is kept in the encapsulating structures of outer
drivers (struct dsa_port :: index, struct ocelot_port_private :: chip_port).
With the upcoming increase in complexity associated with assigning DSA
tag_8021q CPU ports to certain user ports, it becomes necessary for the
switch lib to be able to retrieve the index of a certain ocelot_port.
Therefore, introduce a new u8 to ocelot_port (same size as the chip_port
used by the ocelot switchdev driver) and rework the existing code to
populate and use it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is no longer used since commit 7c4bb540e9 ("net: dsa: tag_ocelot:
create separate tagger for Seville").
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
From Tegra186 onwards, the memory controller supports multiple channels.
Add support for mapping the address spaces of these channels and specify
the number of channels supported by Tegra186, Tegra194 and Tegra234.
In case of old bindings, channels won't be present. If channels are not
present then print a warning and continue so that backward compatibility
will be preserved in driver.
During error interrupts from memory controller, appropriate registers
from these channels need to be accessed for logging error info.
Signed-off-by: Ashish Mhetre <amhetre@nvidia.com>
Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20220506132312.3910637-4-thierry.reding@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
On RK3399 platforms, power domains are managed mostly by the kernel
(drivers/soc/rockchip/pm_domains.c), but there are a few exceptions
where ARM Trusted Firmware has to be involved:
(1) system suspend/resume
(2) DRAM DVFS (a.k.a., "ddrfreq")
Exception (1) does not cause much conflict, since the kernel has
quiesced itself by the time we make the relevant PSCI call.
Exception (2) can cause conflict, because of two actions:
(a) ARM Trusted Firmware needs to read/modify/write the PMU_BUS_IDLE_REQ
register to idle the memory controller domain; the kernel driver
also has to touch this register for other domains.
(b) ARM Trusted Firmware needs to manage the clocks associated with
these domains.
To elaborate on (b): idling a power domain has always required ungating
an array of clocks; see this old explanation from Rockchip:
https://lore.kernel.org/linux-arm-kernel/54503C19.9060607@rock-chips.com/
Historically, ARM Trusted Firmware has avoided this issue by using a
special PMU_CRU_GATEDIS_CON0 register -- this register ungates all the
necessary clocks -- when idling the memory controller. Unfortunately,
we've found that this register is not 100% sufficient; it does not turn
the relevant PLLs on [0].
So it's possible to trigger issues with something like the following:
1. enable a power domain (e.g., RK3399_PD_VDU) -- kernel will
temporarily enable relevant clocks/PLLs, then turn them back off
2. a PLL (e.g., PLL_NPLL) is part of the clock tree for
RK3399_PD_VDU's clocks but otherwise unused; NPLL is disabled
3. perform a ddrfreq transition (rk3399_dmcfreq_target() -> ...
drivers/clk/rockchip/clk-ddr.c / ROCKCHIP_SIP_DRAM_FREQ)
4. ARM Trusted Firmware unagates VDU clocks (via PMU_CRU_GATEDIS_CON0)
5. ARM Trusted firmware idles the memory controller domain
6. Step 5 waits on the VDU domain/clocks, but NPLL is still off
i.e., we hang the system.
So for (b), we need to at a minimum manage the relevant PLLs on behalf
of firmware. It's easier to simply manage the whole clock tree, in a
similar way we do in rockchip_pd_power().
For (a), we need to provide mutual exclusion betwen rockchip_pd_power()
and firmware. To resolve that, we simply grab the PMU mutex and release
it when ddrfreq is done.
The Chromium OS kernel has been carrying versions of part of this hack
for a while, based on some new custom notifiers [1]. I've rewritten as a
simple function call between the drivers, which is OK because:
* the PMU driver isn't enabled, and we don't have this problem at all
(the firmware should have left us in an OK state, and there are no
runtime conflicts); or
* the PMU driver is present, and is a single instance.
And the power-domain driver cannot be removed, so there's no lifetime
management to worry about.
For completeness, there's a 'dmc_pmu_mutex' to guard (likely
theoretical?) probe()-time races. It's OK for the memory controller
driver to start running before the PMU, because the PMU will avoid any
critical actions during the block() sequence.
[0] The RK3399 TRM for PMU_CRU_GATEDIS_CON0 only talks about ungating
clocks. Based on experimentation, we've found that it does not power
up the necessary PLLs.
[1] CHROMIUM: soc: rockchip: power-domain: Add notifier to dmc driver
https://chromium-review.googlesource.com/q/I242dbd706d352f74ff706f5cbf42ebb92f9bcc60
Notably, the Chromium solution only handled conflict (a), not (b).
In practice, item (b) wasn't a problem in many cases because we
never managed to fully power off PLLs. Now that the (upstream) video
decoder driver performs runtime clock management, we often power off
NPLL.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The felix driver is the only user of dsa_port_walk_mdbs(), and there
isn't even a good reason for it, considering that the host MDB entries
are already saved by the ocelot switch lib in the ocelot->multicast list.
Rewrite the multicast entry migration procedure around the
ocelot->multicast list so we can delete dsa_port_walk_mdbs().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
