Add a converter to retrieve NAND timings from an ONFI NAND timing mode.
At the moment, only SDR NAND timings are supported.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Some new Micron flash chips require reading the flag status register to
determine when operations have completed.
Furthermore, chips with multi-die stacks of the 65nm 256Mb QSPI also
require reading the status register before reading the flag status
register.
This patch adds support for the flag status register in the n25q512ax3
and n25q00 Micron QSPI flash chips.
Signed-off-by: Graham Moore <grmoore@altera.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In addition to mtd_block_isbad(), which checks if a block is bad or
reserved, it's needed to check if a block is reserved only (but not
bad). This commit adds an MTD interface for it, in a similar fashion to
mtd_block_isbad().
While here, fix mtd_block_isbad() so the out-of-bounds checking is done
before the callback check.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Pull MTD updates from Brian Norris:
- refactor m25p80.c driver for use as a general SPI NOR framework for
other drivers which may speak to SPI NOR flash without providing full
SPI support (i.e., not part of drivers/spi/)
- new Freescale QuadSPI driver (utilizing new SPI NOR framework)
- updates for the STMicro "FSM" SPI NOR driver
- fix sync/flush behavior on mtd_blkdevs
- fixup subpage write support on a few NAND drivers
- correct the MTD OOB test for odd-sized OOB areas
- add BCH-16 support for OMAP NAND
- fix warnings and trivial refactoring
- utilize new ECC DT bindings in pxa3xx NAND driver
- new LPDDR NVM driver
- address a few assorted bugs caught by Coverity
- add new imx6sx support for GPMI NAND
- use a bounce buffer for NAND when non-DMA-able buffers are used
* tag 'for-linus-20140610' of git://git.infradead.org/linux-mtd: (77 commits)
mtd: gpmi: add gpmi support for imx6sx
mtd: maps: remove check for CONFIG_MTD_SUPERH_RESERVE
mtd: bf5xx_nand: use the managed version of kzalloc
mtd: pxa3xx_nand: make the driver work on big-endian systems
mtd: nand: omap: fix omap_calculate_ecc_bch() for-loop error
mtd: nand: r852: correct write_buf loop bounds
mtd: nand_bbt: handle error case for nand_create_badblock_pattern()
mtd: nand_bbt: remove unused variable
mtd: maps: sc520cdp: fix warnings
mtd: slram: fix unused variable warning
mtd: pfow: remove unused variable
mtd: lpddr: fix Kconfig dependency, for I/O accessors
mtd: nand: pxa3xx: Add supported ECC strength and step size to the DT binding
mtd: nand: pxa3xx: Use ECC strength and step size devicetree binding
mtd: nand: pxa3xx: Clean pxa_ecc_init() error handling
mtd: nand: Warn the user if the selected ECC strength is too weak
mtd: nand: omap: Documentation: How to select correct ECC scheme for your device ?
mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
mtd: nand: omap: add support for BCH16_ECC - ELM driver updates
mtd: nand: omap: add support for BCH16_ECC - GPMC driver updates
...
Fixes warning:
In file included from drivers/mtd/lpddr/qinfo_probe.c:31:0:
include/linux/mtd/pfow.h: In function ‘send_pfow_command’:
include/linux/mtd/pfow.h:104:6: warning: variable ‘chipnum’ set but not used [-Wunused-but-set-variable]
int chipnum;
^
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
nand_base can be passed a kmap()'d buffers from highmem by
filesystems like jffs2. This results in failure to map the
physical address of the DMA buffer on various contoller
driver on different platforms. This change adds a chip option
to use preallocated databuf as bounce buffers used in
nand_do_read_ops() and nand_do_write_ops().
This allows for specific nand controller driver to set this
option as needed.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The nand_chip::erase_cmd callback previously served a dual purpose; for
one, it allowed a per-flash-chip override, so that AG-AND devices could
use a different erase command than other NAND. These AND devices were
dropped in commit 14c6578683 (mtd: nand:
remove AG-AND support). On the other hand, some drivers (denali and
doc-g4) need to use this sort of callback to implement
controller-specific erase operations.
To make the latter operation easier for some drivers (e.g., ST's new BCH
NAND driver), it helps if the command dispatch and wait functions can be
lumped together, rather than called separately.
This patch does two things:
1. Pull the call to chip->waitfunc() into chip->erase_cmd(), and return
the status from this callback
2. Rename erase_cmd() to just erase(), since this callback does a
little more than just send a command
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Lee Jones <lee.jones@linaro.org>
serial_flash_cmds.h defines our opcodes a little differently. Let's
borrow its naming, since it's borrowed from the SFDP standard, and it's
more extensible.
This prepares us for merging serial_flash_cmds.h and spi-nor.h opcode
listing.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Huang Shijie <b32955@freescale.com>
Add the spi_nor_match_id() to find the proper spi_device_id with the
NOR flash's name in the spi_nor_ids table.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch cloned most of the m25p80.c. In theory, it adds a new spi-nor layer.
Before this patch, the layer is like:
MTD
------------------------
m25p80
------------------------
spi bus driver
------------------------
SPI NOR chip
After this patch, the layer is like:
MTD
------------------------
spi-nor
------------------------
m25p80
------------------------
spi bus driver
------------------------
SPI NOR chip
With the spi-nor controller driver(Freescale Quadspi), it looks like:
MTD
------------------------
spi-nor
------------------------
fsl-quadspi
------------------------
SPI NOR chip
New APIs:
spi_nor_scan: used to scan a spi-nor flash.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
[Brian: rebased to include additional m25p_ids[] entry]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The spi_nor{} is cloned from the m25p{}.
The spi_nor{} can be used by both the m25p80 and spi-nor controller.
We also add the spi_nor_xfer_cfg{} which can be used by the two
fundamental primitives: read_xfer/write_xfer.
1) the hooks for spi_nor{}:
@prepare/unpreare: used to do some work before or after the
read/write/erase/lock/unlock.
@read_xfer/write_xfer: We can use these two hooks to code all
the following hooks if the driver tries to implement them
by itself.
@read_reg: used to read the registers, such as read status register,
read configure register.
@write_reg: used to write the registers, such as write enable,
erase sector.
@read_id: read out the ID info.
@wait_till_ready: wait till the NOR becomes ready.
@read: read out the data from the NOR.
@write: write data to the NOR.
@erase: erase a sector of the NOR.
2) Add a new field sst_write_second for the SST NOR write.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds a new header :spi-nor.h,
and copies all the SPI NOR commands and relative macros into this new header.
This hearder can be used by the m25p80.c and other spi-nor controller,
such as Freescale's Quadspi.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
GET_FEATURES and SET_FEATURES also need byte-addressing on 16-bit devices.
Signed-off-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the "page" argument for the read_subpage hook. With this argument,
the implementation of this hook could prints out more accurate information
for debugging.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds the parsing code for the JEDEC compliant NAND.
Since we need the 0x40 as the column address, this patch also
makes the NAND_CMD_PARAM to use the 8-bit address only.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add a helper to get the supported features for JEDEC compliant NAND.
Also add a macro JEDEC_FEATURE_16_BIT_BUS.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add the jedec_version field, and add an anonymous union which
contains the nand_onfi_params and nand_jedec_params.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Create the nand_jedec_params{} and jedec_ecc_info{} according to
the JESD230A (Revision of JESD230, October 2012).
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The NAND command helpers tend to automatically shift the column address
for x16 bus devices, since most commands expect a word address, not a
byte address. The Read ID command, however, expects an 8-bit address
(i.e., 0x00, 0x20, or 0x40 should not be translated to 0x00, 0x10, or
0x20).
This fixes the column address for a few drivers which imitate the
nand_base defaults. Note that I don't touch sh_flctl.c, since it already
handles this problem slightly differently (note its comment "READID is
always performed using an 8-bit bus").
I have not tested this patch, as I only have x8 parts up for testing at
this point. Hopefully that can change soon...
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-By: Pekon Gupta <pekon@ti.com>
