The WM8351 is a WM8350 variant. As well as register default changes the
WM8351 has fewer voltage and current regulators than the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Some WM8350 variants have fewer DCDCs and ISINKs. Identify these at
probe and refuse to use the absent DCDCs when running on these chips.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8352 is a variant of the WM8350. Aside from the register defaults
there are no software visible differences to the WM8350.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch amends DA903x MFD driver with definitions and methods
needed for battery charger driver.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Implement support for reporting battery health in the WM8350 battery
interface. Since we are now able to report this via the classs remove
the diagnostics from the interrupt handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Since the WM8350 driver was originally written the semantics for the
identification registers of the chip have been clarified, allowing
us to do an exact match on all the fields. This avoids mistakenly
running on unsupported hardware.
Also change to using the datasheet names more consistently for
legibility and fix a printk() that should be dev_err().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Rather than check for chip revisions in the WM8350 drivers have the core
code set flags for relevant differences.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
This patch adds support for the PMU provided by the WM8350 which
implements battery, line and USB supplies including a battery charger.
The hardware functions largely autonomously, with minimal software
control required to initiate fast charging.
Support for configuration of the USB supply is not yet implemented.
This means that the hardware will remain in the mode configured at
startup, by default limiting the current drawn from USB to 100mA.
This driver was originally written by Liam Girdwood with subsequent
updates for submission by Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The auxiliary ADC in the WM8350 is shared between several subdevices
so access to it needs to be arbitrated by the core driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
The WM8350 is an integrated audio and power management subsystem which
provides a single-chip solution for portable audio and multimedia systems.
The integrated audio CODEC provides all the necessary functions for
high-quality stereo recording and playback. Programmable on-chip
amplifiers allow for the direct connection of headphones and microphones
with a minimum of external components. A programmable low-noise bias
voltage is available to feed one or more electret microphones.
Additional audio features include programmable high-pass filter in the
ADC input path.
This driver was originally written by Liam Girdwood with further updates
from me.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This adds support for the RTC provided by the Wolfson Microelectronics
WM8350.
This driver was originally written by Graeme Gregory and Liam Girdwood,
though it has been modified since then to update it to current mainline
coding standards and for API completeness.
[akpm@linux-foundation.org: s/schedule_timeout_interruptible/schedule_timeout_uninterruptible/ to prevent bogus timeout when signal_pending()]
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Liam Girdwood <linux@wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch updates the remaining two TMIO drivers to use the clock API
rather than callback hooks into platform code.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
DA9030 (a.k.a ARAVA) and DA9034 (a.k.a MICCO) are PMICs designed by
Dialog Semiconductor, usually found on PXA-based platforms. These
PMICs are I2C-based, multi-function devices, usually with LEDs, PWMs
for backlight, BUCKs and LDOs, ADCs and touchscreen controller (on
DA9034).
This is the base support for the I2C operations, event registration
and handling, sub-devices management.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Liam Girdwood <lrg@kernel.org>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
As requested by Ian make state restore only if it's requested
by platform data: some platforms do correctly save the state of
the chip during suspend/resume, but some (like tosa) incorrectly
power off the chip at suspend, so the driver supports restoring
some bits of the tc6393xb state (not full, merely enough to support
resume on tosa). With this patch this code is disabled by default.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
Instead of using bitfields for initial gpio setup,
provide generic setup/teardown hooks that can be used
to set the gpio states, register child devices, etc.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@openedhand.com>
In order to avoid merge problems further down the line add placeholders
for several of the WM8350 client devices and register them, otherwise
the patches adding the client devices will all try to update the same
code.
Also remove redundant checks for null regulator platform devices while
we're at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 features six DCDC convertors (four buck and two boost), four
LDO voltage regulators and two constant current sinks. This driver adds
support for these through the regulator API.
This driver was written by Liam Girdwood with updates for submission
from Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 has an interrupt line to the CPU which is shared by the
devices on the CPU. This patch adds support for the interrupt
controller within the WM8350 which identifies which identifies the
interrupt cause. In common with other similar chips this is done
outside the standard interrupt framework due to the need to access
the interrupt controller over an interrupt-driven bus.
This code was all originally written by Liam Girdwood with updates for
submission by me.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Some functions of the WM8350 require board-specific initialisation on
startup. Provide a callback to the WM8350 driver in platform data
for platforms to use to configure the chip. Use of a callback allows
platforms to control the ordering of initialisation which can be
important.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 provides a number of user-configurable pins providing access
to various signals generated by the functions on the chip. These are
referred to as GPIO pins in the device documentation but in Linux terms
they are more general than that, providing configuration of alternate
functions.
This patch implements support for selecting the alternate functions for
these pins. They can also be used as GPIOs in the normal Linux sense -
a subsequent patch will add support for doing so.
This code was all written by Liam Girdwood and has had minor updates
and rearrangements by Mark Brown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The WM8350 is an integrated audio and power management subsystem
intended for use as the primary PMIC in mobile multimedia applications.
The WM8350 can be controlled via either I2C or SPI - the control
interface is provided by a separate module in order to allow greatest
flexibility in configuring the kernel.
This driver was originally written by Liam Girdwood and has since been
updated to current kernel APIs and split up for submission by me. All
the heavy lifting here was done by Liam.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
