INIT_DEV_PARAMS and SET_MULTI_MODE change the device parameters cached
by libata. Re-read IDENTIFY DEVICE info and update the cached device
paramters when seeing these commands.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ata IRQ ack functions are only used when debugging. Unfortunately
almost every controller that calls them can cause crashes in some
configurations as there are missing checks for bmdma presence.
In addition ata_port_start insists of installing DMA buffers and pad
buffers for controllers regardless. The SFF controllers actually need to
make that decision dynamically at controller setup time and all need the
same helper - so we add ata_sff_port_start. Future patches will switch
the SFF drivers to use this.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent <linux/console_struct.h> from being included more than once,
otherwise you get a redefinition error if you happen to include
<linux/vt_kern.h> first.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a prefix string parameter. Callers are responsible for any string
length/alignment that they want to see in the output. I.e., callers should
pad strings to achieve alignment if they want that.
Add rowsize parameter. This is the number of raw data bytes to be printed
per line. Must be 16 or 32.
Add a groupsize parameter. This allows callers to dump values as 1-byte,
2-byte, 4-byte, or 8-byte numbers. Default is 1-byte numbers. If the
total length is not an even multiple of groupsize, 1-byte numbers are
printed.
Add an "ascii" output parameter. This causes ASCII data output following
the hex data output.
Clean up some doc examples.
Align the ASCII output on all lines that are produced by one call.
Add a new interface, print_hex_dump_bytes(), that is a shortcut to
print_hex_dump(), using default parameter values to print 16 bytes in
byte-size chunks of hex + ASCII output, using printk level KERN_DEBUG.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
1. New entries can be added to tsk->pi_state_list after task completed
exit_pi_state_list(). The result is memory leakage and deadlocks.
2. handle_mm_fault() is called under spinlock. The result is obvious.
3. results in self-inflicted deadlock inside glibc.
Sometimes futex_lock_pi returns -ESRCH, when it is not expected
and glibc enters to for(;;) sleep() to simulate deadlock. This problem
is quite obvious and I think the patch is right. Though it looks like
each "if" in futex_lock_pi() got some stupid special case "else if". :-)
4. sometimes futex_lock_pi() returns -EDEADLK,
when nobody has the lock. The reason is also obvious (see comment
in the patch), but correct fix is far beyond my comprehension.
I guess someone already saw this, the chunk:
if (rt_mutex_trylock(&q.pi_state->pi_mutex))
ret = 0;
is obviously from the same opera. But it does not work, because the
rtmutex is really taken at this point: wake_futex_pi() of previous
owner reassigned it to us. My fix works. But it looks very stupid.
I would think about removal of shift of ownership in wake_futex_pi()
and making all the work in context of process taking lock.
From: Thomas Gleixner <tglx@linutronix.de>
Fix 1) Avoid the tasklist lock variant of the exit race fix by adding
an additional state transition to the exit code.
This fixes also the issue, when a task with recursive segfaults
is not able to release the futexes.
Fix 2) Cleanup the lookup_pi_state() failure path and solve the -ESRCH
problem finally.
Fix 3) Solve the fixup_pi_state_owner() problem which needs to do the fixup
in the lock protected section by using the in_atomic userspace access
functions.
This removes also the ugly lock drop / unqueue inside of fixup_pi_state()
Fix 4) Fix a stale lock in the error path of futex_wake_pi()
Added some error checks for verification.
The -EDEADLK problem is solved by the rtmutex fixups.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ulrich Drepper <drepper@redhat.com>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Instead of returning the smallest available object return ZERO_SIZE_PTR.
A ZERO_SIZE_PTR can be legitimately used as an object pointer as long as it
is not deferenced. The dereference of ZERO_SIZE_PTR causes a distinctive
fault. kfree can handle a ZERO_SIZE_PTR in the same way as NULL.
This enables functions to use zero sized object. e.g. n = number of objects.
objects = kmalloc(n * sizeof(object));
for (i = 0; i < n; i++)
objects[i].x = y;
kfree(objects);
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently when system which have HPA require HPA to be detected and
disabled upon resume from RAM or disk. The current IDE drivers do not do
this nor does libata (obviously it since it doesn't support HPA yet).
I have implemented this into the current IDE drivers and it has been
tested by many others since 7/15/2006 in bug number 6840:
http://bugzilla.kernel.org/show_bug.cgi?id=6840
and it has been confirmed to work fine with no problems.
bart: added drv != NULL check to generic_ide_suspend()
From: Lee Trager <lt73@cs.drexel.edu>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Michael Schimek requested the addition of inverted alpha framebuffer
caps/flags to support such hardware.
'Normal' alpha uses this formula to mix the framebuffer and video:
output = fb pixel * fb alpha + video pixel * (1 - fb alpha)
and the 'inverted' alpha uses this formula:
output = fb pixel * (1 - fb alpha) + video pixel * fb alpha
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L2_CAP_VIDEO_OUTPUT_POS was initially introduced for 2.6.22 but never
actually used: remove it before the final 2.6.22 is made.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There's really no reason it's below the first use of the pointer
type, and it'll fail compilation for the network addition (for good
reason). So move it up a bit.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
check_compat_entry_size_and_hooks iterates over the matches and calls
compat_check_calc_match, which loads the match and calculates the
compat offsets, but unlike the non-compat version, doesn't call
->checkentry yet. On error however it calls cleanup_matches, which in
turn calls ->destroy, which can result in crashes if the destroy
function (validly) expects to only get called after the checkentry
function.
Add a compat_release_match function that only drops the module reference
on error and rename compat_check_calc_match to compat_find_calc_match to
reflect the fact that it doesn't call the checkentry function.
Reported by Jan Engelhardt <jengelh@linux01.gwdg.de>
Signed-off-by: Dmitry Mishin <dim@openvz.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rfkill name can be made const safely,
this makes the compiler happy when drivers make
it point to some const string used elsewhere.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously inet devices were only constructed when addresses are added
(or rarely in ipmr). Therefore the default config values they get are
the ones at the time of these operations.
Now that we're creating inet devices earlier, this changes the
behaviour of default config values in an incompatible way (see bug
#8519).
This patch creates a compromise by setting the default values at the
same point as before but only for those that have not been explicitly
set by the user since the inet device's creation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously once inetdev_init has been called on a device any changes
made to ipv4_devconf_dflt would have no effect on that device's
configuration.
This creates a problem since we have moved the point where
inetdev_init is called from when an address is added to where the
device is registered.
This patch is the first half of a set that tries to mimic the old
behaviour while still calling inetdev_init.
It propagates any changes to ipv4_devconf_dflt to those devices that
have not had the corresponding attribute set.
The next patch will forcibly set all values at the point where
inetdev_init was previously called.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the ipv4_devconf config members (everything except
sysctl) to an array. This allows easier manipulation which will be
needed later on to provide better management of default config values.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.infradead.org/mtd-2.6:
[JFFS2] Fix obsoletion of metadata nodes in jffs2_add_tn_to_tree()
[MTD] Fix error checking after get_mtd_device() in get_sb_mtd functions
[JFFS2] Fix buffer length calculations in jffs2_get_inode_nodes()
[JFFS2] Fix potential memory leak of dead xattrs on unmount.
[JFFS2] Fix BUG() caused by failing to discard xattrs on deleted files.
[MTD] generalise the handling of MTD-specific superblocks
[MTD] [MAPS] don't force uclinux mtd map to be root dev
Several people have reported LITE-ON LTR-48246S detection failed
because SETXFER fails. It seems the device raises IRQ too early after
SETXFER. This is controller independent. The same problem has been
reported for different controllers.
So, now we have pata_via where the controller raises IRQ before it's
ready after SETXFER and a device which does similar thing. This patch
makes libata always execute SETXFER via polling. As this only happens
during EH, performance impact is nil. Setting ATA_TFLAG_POLLING is
also moved from issue hot path to ata_dev_set_xfermode() - the only
place where SETXFER can be issued.
Note that ATA_TFLAG_POLLING applies only to drivers which implement
SFF TF interface and use libata HSM. More advanced controllers ignore
the flag. This doesn't matter for this fix as SFF TF controllers are
the problematic ones.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
firewire: Install firewire-constants.h and firewire-cdev.h for userspace.
firewire: Change struct fw_cdev_iso_packet to not use bitfields.
firewire: Implement suspend/resume PCI driver hooks.
firewire: add to MAINTAINERS
firewire: fw-sbp2: implement sysfs ieee1394_id
ieee1394: sbp2: offer SAM-conforming target port ID in sysfs
ieee1394: fix calculation of sysfs attribute "address"
The <linux/serial_core.h> header refers to handle_sysrq(), but does not
include <linux/sysrq.h> which provides a declaration of the function. This
may result in an implicit declaration and a warning if the actual one is
seen later on.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the forward declaration of fb_class from drivers/video/console/fbcon.h to
<linux/fb.h>, together with the other forward declarations related to
drivers/video/fbmem.c.
This kills the following sparse warning:
| drivers/video/fbmem.c:1363:14: warning: symbol 'fb_class' was not declared. Should it be static?
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On systems with huge amount of physical memory, VFS cache and memory memmap
may eat all available system memory under 4G, then the system may fail to
allocate swiotlb bounce buffer.
There was a fix for this issue in arch/x86_64/mm/numa.c, but that fix dose
not cover sparsemem model.
This patch add fix to sparsemem model by first try to allocate memmap above
4G.
Signed-off-by: Zou Nan hai <nanhai.zou@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
