Add ethernet-related fields to struct mlx4_cqe so that the mlx4_en
ethernet NIC driver can share the same definition.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add fields for VLAN tag and insert VLAN tag flag to the control
section struct. These fields will be used for sending ethernet
packets.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for the following operations to mlx4 when device firmware
supports them:
- Send with invalidate and local invalidate send queue work requests;
- Allocate/free fast register MRs;
- Allocate/free fast register MR page lists;
- Fast register MR send queue work requests;
- Local DMA L_Key.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for handling the IB_QP_CREATE_MULTICAST_BLOCK_LOOPBACK
flag by using the per-multicast group loopback blocking feature of
mlx4 hardware.
Signed-off-by: Ron Livne <ronli@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extend the mlx4_cq_resize() API with a way to set the "collapsed" flag
for the CQ being created.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrap doorbell, buffer and MTT allocation in helper functions for
ethernet and FC modules to use.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In addition to mlx4_ib, there will be ethernet and FC consumers of
mlx4_core, so move the code for managing kernel doorbells into the
core module to avoid having to duplicate this multiple times.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX devices support checksum generation and verification of TCP
and UDP packets for UD IPoIB messages. This patch checks if the HCA
supports this and sets the IB_DEVICE_UD_IP_CSUM capability flag if it
does. It implements support for handling the IB_SEND_IP_CSUM send
flag and setting the csum_ok field in receive work completions.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Ali Ayub <ali@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct mlx4_interface.event() method was supposed to get an enum
mlx4_dev_event, but the driver code was actually passing in the
hardware enum mlx4_event values. Fix up the callers of
mlx4_dispatch_event() so that they pass in the right type of value,
and fix up the event method in mlx4_ib so that it can handle the enum
mlx4_dev_event values.
This eliminates the need for the subtype parameter to the event
method, so remove it.
This also fixes the sparse warning
drivers/net/mlx4/intf.c:127:48: warning: mixing different enum types
drivers/net/mlx4/intf.c:127:48: int enum mlx4_event versus
drivers/net/mlx4/intf.c:127:48: int enum mlx4_dev_event
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that struct mlx4_buf.u is a struct instead of a union because of
the vmap() changes, there's no point in having a struct at all. So
move .direct and .page_list directly into struct mlx4_buf and get rid
of a bunch of unnecessary ".u"s.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since kernel virtual memory is not a problem on 64-bit systems, there
is no reason to use our own 2-layer page mapping scheme for large
kernel queue buffers on such systems. Instead, map the page list to a
single virtually contiguous buffer with vmap(), so that can we access
buffer memory via direct indexing.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We use struct mlx4_buf for kernel QP, CQ and SRQ buffers, and the code
to look up an entry is duplicated in get_cqe_from_buf() and the QP and
SRQ versions of get_wqe(). Factor this out into mlx4_buf_offset().
This will also make it easier to switch over to using vmap() for buffers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
display the following device information under /sys/class/infiniband/mlx4_X:
board_id, fw_ver, hw_rev, hca_type.
This patch makes this information available to userspace utilities
such as ibstat and ibv_devinfo.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Get the maximum message size from the device capabilities returned
from the QUERY_DEV_CAP firmware command, rather than hard-coding 2 GB.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Inline data segments in send WQEs are not allowed to cross a 64 byte
boundary. We use inline data segments to hold the UD headers for MLX
QPs (QP0 and QP1). A send with GRH on QP1 will have a UD header that
is too big to fit in a single inline data segment without crossing a
64 byte boundary, so split the header into two inline data segments.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
